Installation Instructions

ManualsBrandsToro ManualsAttachmentsCE Kit, Groundsmaster 360 Multi-Purpose Machine

FormNo.3367-313RevA

CEKit

Groundsmaster360Multi-PurposeMachine

ModelNo.30507

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof

potentialdanger.Replaceanydecalthatisdamagedorlost.

117-3274

1.Tippinghazard—donotmowacrossslopesgreaterthan

16degrees,donotmowupanddownslopesgreaterthan

17degrees.

117-3294

1.Tippinghazard—donotmowacrossslopesgreaterthan

18degrees,donotmowupanddownslopesgreaterthan

19degrees.

117-3293

1.Tippinghazard—donotmowacrossslopesgreaterthan

18degrees,donotmowupanddownslopesgreaterthan

21degrees.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3367-313 Rev A CE Kit Groundsmaster 360 Multi-Purpose Machine Model No. 30507 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117-3274 1.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 3
Figure 1 1. Flange head bolt 2. Storage compartment support bracket 3. Push nut Figure 2 1. Plug 2. Latch 3. Latch key 4. Install the flange head bolts into the storage compartment support bracket using push nuts (3/8 inch). 5. Secure the storage compartment support bracket with the flange head bolts. 4. Install the locking latch through the square hole in the right side of the hood. The catch must be positioned inside the hood and pointing downward. 2 5.
PAGE 4
3 4 Securing the Floor Plate Securing the Seat Plate Parts needed for this procedure: Parts needed for this procedure: 1 Flange head bolt (3/8 x 1 inch) 1 Flange head bolt (3/8 x 1 inch) 1 Push nut (3/8 inch) 1 Push nut (3/8 inch) 1 Retaining nut (3/8 inch) 1 Retaining nut (3/8 inch) Procedure Procedure 1. Raise the floor plate. 1. Raise the seat plate. 2. Install a retaining nut at the frame hole under the right front corner of the floor plate (Figure 3). 2.
PAGE 5
6 Securing the Front Cover Securing the Belt Covers Parts needed for this procedure: Parts needed for this procedure: 2 Push nut Procedure 1. Remove the (2) flange head bolts securing the front cover to the top of the front axle (Figure 5). 2 Flange head bolt (5/16 x 1-1/4 inches) 2 Retaining nut (5/16 inch) 2 Push nut Procedure Perform this procedure for the right and left side belt covers. 1. Remove the hand knobs securing the belt covers to the mower deck (Figure 6).
PAGE 6
7 8 Securing the Floor Plate Securing the Fire Wall Parts needed for this procedure: Parts needed for this procedure: 4 Push nut 4 Push nut Procedure Procedure (Cab models only) (Cab models only) 1. Remove the (4) bolts securing the floor plate to the frame (Figure 7). 1. Remove the (4) bolts securing the fire wall to the frame (Figure 8). Figure 7 1. Floor plate 2. Flange head bolt Figure 8 3. Push nut 1. Fire wall 2. Flange head bolt 3. Push nut 2.
PAGE 7
9 Installing the Decal Parts needed for this procedure: 1 Safety decal, 117–3274 1 Safety decal, 117–3294 1 Safety decal, 117–3293 Procedure 1. Thoroughly clean the area where the decal is to be installed (Figure 9). Figure 9 1. Decal 2. Determine which decal is applicable for the model of the machine, peel the decal from the backing and install it in place. Discard remaining decals.
PAGE 8