Installation Instructions

ManualsBrandsToro ManualsAttachmentsGrammer Seat with Air Ride Suspension Kit, Groundsmaster 360 Multi-Purpose Machine or 7200 Traction Unit

FormNo.3370-734RevA

GrammerSeatwithAirRideSuspensionKit

Groundsmaster

360Multi-PurposeMachineor7200TractionUnit

ModelNo.30511

InstallationInstructions

Installation

RemovingtheExistingSeat

1.Parkthemachineonalevelsurface,lowerthedeck,

engagetheparkingbrake,andturntheengineoff.

Removethekeyfromtheignitionswitch.

2.Disconnectthenegativebatterycablefromthe

battery.

3.Releaseandraisetheseat.Makesuretheseatlatch

isengaged.

4.Disconnecttheseatswitchwirefromthetraction

unitharness(

Figure1).

g017171

Figure1

1.Seatswitchwireconnector

2.Wireharnessclips

5.Removeanyharnessclipsorcabletiessecuringthe

seatwireharnesstotheseatplate(Figure1).

6.Removethefastenerssecuringtheseatbasetothe

seatmountsandseatplate.Lifttheseatandseatbase

offthemachine(Figure2).

g017172

Figure2

1.Seatbasefasteners3.Seatplate

2.Seatbase

7.Removethefastenerssecuringtheseattotheseat

base(Figure3).Removetheseat.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3370-734 Rev A Grammer Seat with Air Ride Suspension Kit Groundsmaster® 360 Multi-Purpose Machine or 7200 Traction Unit Model No. 30511 Installation Instructions 1 Installation Removing the Existing Seat 2 1. Park the machine on a level surface, lower the deck, engage the parking brake, and turn the engine off. Remove the key from the ignition switch. 3 2. Disconnect the negative battery cable from the battery. 3. Release and raise the seat. Make sure the seat latch is engaged. 4.
PAGE 2
1 2 1 g017174 2 Figure 4 1. Rear of seat slide 2. Seat base 2. Mount the front of each seat slide to the seat base with a bolt and flange nut (Figure 5). g017173 Figure 3 1. Seat 2. Seat base Installing the Seat on a Groundsmaster 360 Note: Move the seat slides fore and aft to access the mounting holes for the fasteners. 1. Mount the rear of each seat slide to the seat base with a bolt and flange nut (Figure 4). 2 1 g017175 Figure 5 1. Front of seat slide 2. Seat base 3.
PAGE 3
8. Disengage the seat latch and lower the seat. 5. Route the harness up through the hole in the seat base and insert the remaining harness clip into the hole in the seat base (Figure 6). 4 9. Connect the negative battery cable to the battery. Installing the Seat on a Groundsmaster 7200 3 Important: The Groundsmaster 7200 must be equipped with the Auxiliary Power Unit, Model 30382 to operate the seat kit. Note: Move the seat slides fore and aft to access the mounting holes for the fasteners. 1.
PAGE 4
Operation Positioning the Seat 2 1 Figure 11 g017175 Figure 9 1. Front of seat slide 1. Fore/Aft adjustment lever 4. Armrest adjustment knob 2. Weight adjustment lever 5. Lumbar support adjusting knob 2. Seat plate 3. Backrest locking lever 3. Connect the new wire harness as follows: • Plug the harness connector labeled Seat into the harness connector from the seat (Figure 10). • Plug the harness connector labeled Seat Switch into the traction unit harness (Figure 10).
PAGE 5
Changing the Seat Position When turning the knob to the outside (+) the front part of the armrest will be lifted, when turning the knob to inside (-) it will be lowered. The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. Changing the Backrest Position 1. To adjust, lift the lever to unlock the seat (Figure 11). The back of the seat can be adjusted to provide a more comfortable ride.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8