Installation Instructions

ManualsBrandsToro ManualsAttachmentsJack-Stand Kit, Groundsmaster 360 Series Multi-Purpose Machine

FormNo.3370-429RevB

JackStandKit

Groundsmaster360SeriesMulti-PurposeMachine

ModelNo.30579

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof

potentialdanger.Replaceanydecalthatisdamagedorlost.

Yourkitwillincludeoneofthefollowingdecals:

107-3969

1.Warning—readtheOperator'sManual.

2.Crushinghazard,mower—engagetheparkingbrake,stop

theengine,andremovetheignitionkeybeforeworking

underthemower.

120-6776

1.Warning—readtheOperator'sManual.

2.Crushinghazard,mower;engagetheparkingbrake,stop

theengine,andremovetheignitionkeybeforeworking

underthemower.Alwaysusejackstands.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Jackbracket1

Jackstoragebracket1

Jacksupportbracket1

Swiveljack

Carriagebolt(1/4x1-1/2inches)

Bungee(8inch)

Flatwasher1

Hexangenut

Hex-headangebolt

Hex-headbolt1

Locknut6

Installthekit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3370-429 Rev B Jack Stand Kit Groundsmaster 360 Series Multi-Purpose Machine Model No. 30579 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Your kit will include one of the following decals: 107-3969 120-6776 1. Warning—read the Operator's Manual. 2.
PAGE 2
Installing the Kit Preparing the Machine 1. Park the machine on a level surface, and lower the mower deck and any attachments to the ground. 1 2. Stop the engine, wait for all moving parts to stop, engage the parking brake, and remove the key from the ignition switch. G019065 3 Installing the Kit to a Machine with a Quick-Attach System 2 Figure 2 1. Secure the bungee to the jack storage bracket with a carriage bolt, a flat washer, and a hex-flange nut (Figure 1). 1. Pin 2. Jack storage bracket 3.
PAGE 3
Installing the Kit to a Machine without a Quick-Attach System 1. Secure the bungee to the jack support bracket with a carriage bolt, a flat washer, and a hex-flange nut (Figure 4). Figure 5 Figure 4 1. Jack support bracket 4. Carriage bolt 2. Hex-flange nut 5. Bungee 3. Flat washer 1. Jack support bracket 4. Hex-head bolt (1/2 x 4-1/2 inches) 2. Hex-head flange bolt (1/2 x 1-1/2 inches) (4) 5. Locknut (5) 3. Jack bracket 2.
PAGE 4
Operation Storage 1. Remove the jack from the jack storage bracket (on a machine with a Quick-Attach System) or the jack support bracket (on a machine without a Quick-Attach System). 1. Hook the hub of the jack onto the tab of the jack storage bracket (Figure 7) or onto the tab of the jack bracket (Figure 8). 2. Install the hub of the jack over the hub of the jack bracket (Figure 6). G019067 Figure 7 With Quick-Attach System G019074 Figure 6 3.
PAGE 5
1 G019068 Figure 9 With Quick-Attach System 1. Hook the bungee end here. Figure 10 Without Quick-Attach System 1. Hook the bungee end here.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8