Form No. 3401-488 Rev A Groundsmaster® 4000 Rotary Mower Model No. 30605—Serial No. 316000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. 1 WARNING CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. g028455 Figure 1 Genuine Toro spark arresters are approved by the USDA Forestry Service. 1.
Servicing the Battery...............................................44 Locating the Fuses..................................................45 Drive System Maintenance .........................................45 Adjusting the Traction-Pedal Angle...........................45 Checking the Planetary-Gear-Drive Oil .....................45 Changing the Planetary-Gear-Drive Oil .....................46 Checking the Rear-Axle Lubricant.............................46 Checking the Rear-Axle-Gearbox Lubricant ........
Sound Pressure Level Safety This unit has a sound pressure level at the operator’s ear of 91 dBA, which includes an Uncertainty Value (K) of 1 dBA. This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. Sound pressure level was determined according to the procedures outlined in EN ISO 5395:2013. Improper use or maintenance by the operator or owner can result in injury.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7272 1. Cutting/dismemberment hazard; fan—stay away from moving parts. 100-5622 1. Height-of-cut adjustment 93-7275 1. Read the Operator's Manual. 2. Do not use starting aids. 100-5623 1. Low height-of-cut adjustment 2. High height-of-cut adjustment 93-7818 1.
100-5693 104-3579 1. Height-of-cut adjustment 1. Low height-of-cut adjustment 2. High height-of-cut adjustment 106-6754 100-5694 1. Warning—do not touch the hot surface. 1. Height-of-cut adjustment 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 100-6578 1. Entanglement hazard, belt—do not operate the machine with the shields or guards removed; always keep the shields and guards in place; stay away from moving parts. 106-6755 1.
114-0846 4. Pull the knob out to 1. Read the Operator’s engage the PTO. Manual for information on starting the engine—1) Set to neutral; 2) Engage the brake; 3) Set the engine speed to slow; 4) Turn the ignition key to preheat; 5) Turn the ignition key to engine start. 2.
120-4159 1. Off 2. Lights 3. On 4. Light-switch location 120-4130 1. Read the Operator’s Manual. 2. To engage the parking brake—1) Lock the pedals together; 2) Push down on the brake; 3) Pull out the parking brake knob. 3. Parking brake 8. High 9. Traction drive 10. Low 11. Power takeoff (PTO) 5. Fast 12. Lower, left deck 6. Variable-speed adjustment 13. Lower, center deck 4. To disengage the parking brake, push down on the brake pedal. 7. Slow 14. Lower, right deck 120-6604 1.
121-3884 1. Engine—stop 3. Engine—start 2. Engine—preheat 120-8947 1. Warning—read the Operator’s Manual. 4. If the roll bar is raised, wear the seat belt. 2. There is no rollover 5. If the roll bar is lowered, protection when the roll do not wear the seat belt. bar is down. 3. There is rollover protection 6. Drive slowly when turning. when the roll bar is up. 121-3887 1. Read the Operator’s Manual. 121-1599 1. Read the Operator’s Manual for information on fuses. 127-3700 1. Raise the left deck 4.
Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3. Caustic liquid/chemical burn hazard 4. Wear eye protection. 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 5. Read the Operator's Manual. 10. Contains lead; do not discard.
7-2766 (Affix over Part No. 117-2754 for CE*) * This safety decal includes a slope warning required on the machine for compliance to the European Lawn Mower Safety Standard EN836:1997. The conservative maximum slope angles indicated for operation of this machine are prescribed by and required by this standard. 1. Warning—read the Operator's Manual. 2. Warning—do not operate this machine unless you are trained. 3. Warning—wear the seat belt when seated in the operator's position. 4.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 Use Qty. No parts required – Grease the machine. Warning decal 1 Replace the warning decal. No parts required – Check the tire pressure. No parts required – Check the fluid levels. Media and Additional Parts Description Use Qty.
Product Overview 3 Controls Checking the Tire Pressure Note: Determine the left and right sides of the machine from the normal operating position. No Parts Required Procedure Check the tire pressure; refer to Checking the Tire Pressure (page 21). 9 4 Checking the Fluid Levels No Parts Required 10 g020756 Figure 3 Procedure 1. Check the engine-oil level; refer to Checking the Engine-Oil Level (page 41). 2. Check the hydraulic fluid level; refer to Checking the Hydraulic Fluid (page 52). 3.
Parking-Brake Latch PTO Switch A knob on the left side of the console actuates the parking-brake lock (Figure 3). The PTO switch has 2 positions: OUT (START) and IN (STOP). Pull the PTO button out to engage the mower-deck blades. Push the button in to disengage the mower-deck blades (Figure 4). To engage the parking brake, connect the pedals with the locking latch, push down on both pedals, and pull the parking-brake latch out.
Power-Point Port Using the InfoCenter Control The power-point port is used to power optional electrical accessories (Figure 5). The InfoCenter LCD display shows information about your machine such as the operating status, various diagnostics and other information about the machine (Figure 7). There is a splash screen and main information screen of the InfoCenter.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.
InfoCenter Icon Description (cont'd.) Operator should change to the indicated state Symbols are often combined to form sentences. Some examples are shown below Settings The Settings menu allows you to customize and modify configuration variables on the InfoCenter display. About The About menu lists the model number, serial number, and software version of your machine.
Trans Speed Controls the maximum speed while in transport (high range) Smart Power Smart Power prevents bogging down in heavy turf by automatically controlling the machine speed and optimizing cutting performance. the passcode. Changing Protect Settings to the ON position hides the protected options and requires entering a passcode to change the setting in the Protected Menu. After you have set the passcode, you must turn the key switch off and then on to enable and save this feature.
Specifications Operation Note: Specifications and design are subject to change without notice. Before Operation Width of cut: Overall 335 cm (132 inches) Before Operation Safety Front mower deck 157 cm (62 inches) Wing mower deck 107 cm (42 inches) General Safety Front and 1 wing mower deck 246 cm (97 inches) • Never allow children or untrained people to operate or service the machine. Local regulations may restrict the age of the operator.
Fuel Safety Checking the Engine-Oil Level Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 41). DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Checking the Cooling System • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills.
Biodiesel Ready Checking the Tire Pressure This machine can also use a biodiesel blended fuel of up to B20 (20% biodiesel, 80% petrodiesel). The petrodiesel portion should be low or ultra-low sulfur. Observe the following precautions: Service Interval: Before each use or daily • The biodiesel portion of the fuel must meet specification Low tire pressure decreases machine side-hill stability. This could cause a rollover, which may result in personal injury or death. DANGER ASTM D6751 or EN14214.
Adjusting the Rollover Protection System (ROPS) Checking the Torque of the Wheel-Lug Nuts Service Interval: After the first hour WARNING After the first 10 hours To avoid injury or death from rollover: keep the roll bar in the raised locked position and use the seat belt. Every 200 hours Torque the wheel-lug nuts to 115 to 136 N∙m (85 to 100 ft-lb) in the order shown in Figure 10 and Figure 11. Ensure that the seat is secured with the seat latch.
Lowering the ROPS Adjusting the Height of Cut Important: Lower the roll bar only when absolutely necessary. Front Mower Deck The height of cut is adjustable from 25 to 127 mm (1 to 5 inches) in 13 mm (1/2 inch) increments. To adjust the height of cut on the front mower deck, position the caster-wheel axles in the upper or lower holes of the caster forks, add or remove an equal number of spacers from the caster forks, and secure the rear chain to the desired hole.
Wing Mower Decks To adjust the height of cut on the wing mower decks, add or remove an equal number of spacers from the caster forks, position the caster-wheel axles in the high or low height-of-cut holes in the caster forks, and secure the pivot arms to the selected height-of-cut bracket holes. 1. Position the caster-wheel axles in the same holes in all of the caster forks (Figure 18 and Figure 20). 2. Remove the tensioning cap from the spindle shaft and slide the spindle out of the caster arm (Figure 18).
5. Remove the hairpin cotter and clevis pins from the caster-pivot arms (Figure 20). 6. Rotate the tension rod to raise or lower the pivot arm until the holes are aligned with the selected height-of-cut bracket holes in the mower-deck frame (Figure 20 and Figure 21). Figure 22 1. Damper link 10. Align the damper-link holes with the selected height-of-cut bracket holes in the mower-deck frame, insert the clevis pins, and install the hairpin cotters (Figure 23). Figure 20 1. Caster-pivot arm 2.
Adjusting the Mower-Deck Rollers Adjusting the Skids Mount the skids in the lower position when operating at heights of cut greater than 64 mm (2-1/2 inches) and in the higher position when operating at heights of cut lower than 64 mm (2-1/2 inches). The mower-deck rollers should be mounted in the lower position when operating at height of cuts greater than 64 mm (2-1/2 inches) and in the higher position when operating in height of cuts lower than 64 mm (2-1/2 inches).
Setting up the Front Mower Deck 1. Rotate the blade on each spindle until the ends face forward and backward. 2. Measure from the floor to the front tip of the cutting edge. 3. Adjust the shims (3 mm or 1/8 inch) on the front caster fork(s) to match the height-of-cut decal (Figure 26); refer to Adjusting the Mower-Deck Pitch (page 55). Figure 27 1. Front caster arm 2. Shims 3. Front caster fork Matching the Height of Cut Between Mower Decks 1.
engine does move, there is a malfunction in the interlock system that should be corrected before beginning operation. (3 mm or 1/8 inch) from the front, outside caster arm of the wing mower deck. 7. If the inside edge of the wing mower deck is too low relative to the outside edge of the front mower deck, add a shim (3 mm or 1/8 inch) to the bottom of the front, inside caster arm on the wing mower deck.
Slope Safety • Slow down and use caution when making turns and crossing roads and sidewalks with the machine. Always yield the right-of-way. • Slow down the machine and use extra care on hillsides. Travel in the recommended direction on hillsides. Turf conditions can affect the stability of the machine. • Turn on the flashing warning lights on the machine whenever you travel on a public road, except where such use is prohibited by law. • Avoid starting, stopping, or turning the machine on a slope.
Stopping the Engine Using Cruise Control Important: Allow the engine to idle for 5 minutes before shutting it off after a full-load operation. This allows the turbocharger to cool down before shutting the engine off. Failure to do so may lead to turbocharger trouble. The cruise-control switch locks in the pedal position to maintain the desired ground speed.
Adjusting the Transport Speed Before stopping the engine, disengage all controls and change the throttle to SLOW . Changing the throttle to SLOW reduces high engine speed, noise, and vibration. Turn the key to the OFF position to shut off the engine. Supervisor (Protected Menu) Allows the supervisor to set the maximum transport speed, in increments of 50%, 75% or 100%, at which the operator can transport (high range).
After Operating After Operation To ensure optimum performance, clean the underside of the mower housing after each use. If residue builds up in the mower housing, cutting performance decreases. After Operation Safety Also, remove any debris which may have collected between the deck-lift cylinders and the foam deck pads (Figure 29). General Safety • Clean grass and debris from the cutting units, drives, mufflers, and engine to help prevent fires. Clean up oil or fuel spills.
Pushing or Towing the Machine Locating the Jacking Points There are jacking points located at the front and rear of the machine. In an emergency, the machine can be moved forward by actuating the bypass valve in the variable-displacement hydraulic pump and pushing or towing the machine. WARNING Always use jack stands. Do not rely on a jack or hoist to hold the machine. Important: Do not push or tow the machine faster than 3 to 4.8 km/h (2 to 3 mph), because internal-transmission damage may occur.
Maintenance Note: Download a free copy of the schematic by visiting www.Toro.com and searching for your machine from the Manuals link on the home page. Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour Maintenance Procedure • Torque the wheel-lug nuts. After the first 10 hours • Torque the wheel-lug nuts. • Check the alternator-belt tension.
Maintenance Service Interval Maintenance Procedure Every 1,000 hours • Check and adjust the engine-valve clearance. Every 2 years • Flush the cooling system and replace the fluid. • Replace moving hoses. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance. Daily Maintenance Checklist Duplicate this page for routine use.
Important: Refer to your engine operator’s manual for additional maintenance procedures. Notation for Areas of Concern Inspection performed by: Item Date Information Service Interval Chart Figure 32 Premaintenance Procedures 4. Move the traction pedal to the NEUTRAL position. 5. Engage the parking brake. 6. Move the throttle switch to the LOW -IDLE position. Pre-Maintenance Safety 7. Shut off the engine and remove the key. • Keep all parts of the machine in good working condition 8.
Lubrication • Do not touch parts of the machine or an attachment that may be hot from operation. Allow the parts to cool before attempting to maintain, adjust, or service them. Greasing the Bearings and Bushings • Use jack stands to support the machine and/or its components when required. • Carefully release pressure from components with stored Service Interval: Every 50 hours (lubricate after every washing). energy.
g017810 Figure 38 Front Lift Assemblies • 2 (each side) lift-arm-cylinder bushings (Figure 39) • 2 lift-arm-ball joints (Figure 40) Figure 36 Front Mower Deck Figure 39 • 2 caster-fork-shaft bushings (Figure 37) • 3 spindle-shaft bearings—located under the pulley (Figure 38) • 2 idler-arm-pivot bushings (Figure 38) Figure 40 Figure 37 38
Wing Mower Decks • 1 caster-fork-shaft bushing (Figure 41) • 2 (each side) spindle-shaft bearings—located under the pulley • 1 idler-arm-pivot bushings—located on the idler arm Figure 43 Figure 41 Figure 44 Side Lift Assemblies • 6 main lift-arm bushings (Figure 42 and Figure 43) • 2 bell-crank-pivot bushings (Figure 44) • 4 rear arm bushings (Figure 44) • 4 lift-cylinder bushings (Figure 45) Figure 45 Figure 42 39
Engine Maintenance Engine Safety Shut off the engine before checking the oil or adding oil to the crankcase. Servicing the Air Cleaner Service Interval: Before each use or daily—Check the air-cleaner indicator Every 50 hours—Inspect the air cleaner. Every 400 hours—Service the air cleaner (earlier if the air cleaner indicator shows red, and more frequently in extremely dirty or dusty conditions). Check the air-cleaner body for damage, which could cause an air leak. Replace it if it is damaged.
Figure 48 1. Air-cleaner safety filter 2. Reset the indicator (Figure 46) if it shows red. Checking the Engine-Oil Level Service Interval: Before each use or daily The engine is shipped with oil in the crankcase; however, the oil level must be checked before and after the engine is first started. Figure 49 The crankcase capacity is approximately 5.7 L (6 US qt) with the filter. Note: When using different oil, drain all old oil from the crankcase before adding new oil.
Changing the Engine Oil and Filter Fuel System Maintenance Service Interval: Every 250 hours 1. Start the engine and let it run 5 minutes to allow the oil to warm up. Servicing the Fuel System 2. Park the machine on a level surface, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Draining the Fuel Tank Service Interval: Every 800 hours (also if the fuel system is contaminated). 3. Replace the engine oil and filter (Figure 50).
Servicing the Water Separator Electrical System Maintenance Service Interval: Before each use or daily—Drain water or other contaminants from the water separator. Electrical System Safety Every 400 hours • Disconnect the battery before repairing the machine. Service the water separator as shown in Figure 51. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Battery acid is poisonous and can cause burns.
Servicing the Battery WARNING Battery terminals or metal tools could short against metal components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Service Interval: Every 25 hours—Check the electrolyte level (or every 30 days if the machine is in storage). Every 50 hours—Check the condition of the battery. Important: Before welding on the machine, disconnect the negative cable from the battery to prevent damage to the electrical system.
Locating the Fuses Drive System Maintenance The traction-unit fuses are located under the power-center cover (Figure 54, Figure 55, and Figure 56). Remove the 2 screws securing the power-center cover to the frame and remove the cover (Figure 54). Adjusting the Traction-Pedal Angle 1. Loosen the 2 nuts and bolts securing the left side of the traction pedal to the bracket (Figure 57). Figure 54 1. Power-center cover 2. Screws Figure 57 1. Traction pedal 2. Mounting nuts and bolts 2.
Note: The oil level should be at the bottom of the check-plug hole. 6. Through the open hole, slowly fill the planetary with 0.65 L (22 oz) of high quality SAE 85W-140 wt gear lube. 3. If the oil level is low, remove the plug at the 12 o’clock position and add oil until it begins to flow out of the hole at the 3 o’clock position. Important: If the planetary fills before the 0.
Checking the Rear-Axle-Gearbox Lubricant Service Interval: Every 400 hours The gearbox is filled with SAE 85W-140 gear lube. The capacity is 0.5 L (16 oz). Visually inspect for leaks daily. 1. Position the machine on a level surface. 2. Remove the check/fill plug from the left side of the gearbox and ensure that lubricant is up to the bottom of the hole (Figure 62). Figure 63 Note: If the level is low, add enough lubricant to bring the level up to the bottom of the hole. 1. Drain-plug location 5.
Checking the Rear Wheel Toe-In Cooling System Maintenance Service Interval: Every 800 hours Cooling System Safety 1. Measure the center-to-center distance (at axle height) at the front and rear of the steering tires. CAUTION Note: The front measurement must be 6 mm (1/4 inch) less than the rear measurement. Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. • Do not remove the radiator cap when the engine is hot.
Brake Maintenance Important: Do not use water only or alcohol/methanol base coolants, as this may cause damage. Adjusting the Service Brakes 4. Install the radiator cap and expansion-tank cap. Adjust the service brakes when there is more than 25 mm (1 inch) of “free travel” of the brake pedal, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before you feel braking resistance. Servicing the Engine-Cooling System 1.
Belt Maintenance Servicing the Alternator Belt Service Interval: After the first 10 hours Every 100 hours Proper tension allows 10 mm (3/8 inch) of deflection when a force of 44 N∙m (10 ft-lb) is applied on the belt midway between the pulleys. If the deflection is not 10 mm (3/8 inch), loosen the alternator-mounting bolts (Figure 69). Note: Increase or decrease the alternator-belt tension and tighten the bolts. Check the deflection of the belt again to ensure that the tension is correct. Figure 68 1.
Figure 71 1. Hydraulic motor 2. Mounting bolts Figure 70 1. Belt 4. Belt guide 2. Eye bolt 5. Flange nut 3. Extension spring 6. Stop bolt 5. Lift the motor off the mower deck and lay it on top of the mower deck. 6. Remove the old belt from around the spindle pulleys and idler pulley. 7. Route the new belt around the spindle pulleys and idler-pulley assembly. Replacing the Blade-Drive Belt 8. Position the hydraulic motor on the mower deck after routing the belt around the pulleys.
Hydraulic System Maintenance High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 Material Properties: Viscosity, ASTM D445 Hydraulic System Safety St @ 40° C 44 to 48 St @ 100° C 7.9 to 8.5 140 to 160 Viscosity Index ASTM D2270 WARNING Pour Point, ASTM D97 Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
Changing the Hydraulic Fluid Service Interval: Every 800 hours Change the hydraulic fluid after every 800 operating hours, in normal conditions. If the fluid becomes contaminated, contact your local Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. 1. Position the machine on a level surface, lower the mower decks, shut off the engine, and remove the key. 2.
Replacing the Hydraulic Filters Adjusting the Counterbalance Pressure Service Interval: After the first 200 hours Every 800 hours The counterbalance test port is used to test the pressure in the counterbalance circuit (Figure 75). The recommended counterbalance pressure is 2,241 kPa (325 psi). To adjust the counterbalance pressure, loosen the locknut, rotate the adjusting screw (Figure 75) clockwise to increase the pressure, or counterclockwise to decrease the pressure and tighten the locknut.
Mower Maintenance 4. Sit on the seat, start the engine, and lower the mower deck until it is slightly off the floor. Pivoting (Tilting) the Front Mower Deck to the Upright Position 5. Secure the height-of-cut chains to the rear of the mower deck. 6. Pivot the transport latch upward into position and secure it with the clevis pin and cotter pin. Note: Although not needed for normal maintenance procedures, the front mower deck can be pivoted (tilted) to an upright position.
Adjusting the Wing Mower-Deck Pitch Service Interval: Every 800 hours 1. Remove the tensioning cap from the spindle shaft and slide the spindle out of the caster arm (Figure 78). Note: Position the shims, as required, to raise or lower the caster wheel until the mower deck has the correct pitch. Figure 79 1. Caster-arm tube 2. Bushings 5. Apply grease to the inside and outside of the new bushings. 6. Using a hammer and flat plate, drive the bushings into the mounting tube. 7.
Blade Maintenance Blade Safety DANGER A worn or damaged blade can break, and a piece of the blade could be thrown at you or bystanders, resulting in serious personal injury or death. Trying to repair a damaged blade may result in discontinued safety certification of the product. • Inspect the blade periodically for wear or damage. • Never try to straighten a blade that is bent or weld a broken or cracked blade. • Replace a worn or damaged blade. Figure 81 1. Caster wheel 3. Bearing 2.
Removing and Installing the Mower Blade(s) Inspecting and Sharpening the Mower Blade(s) The blade must be replaced if a solid object is hit, the blade is out of balance, or if the blade is bent. Always use genuine Toro replacement blades to ensure safety and optimum performance. Consider 2 areas when checking and servicing the mower blade—the sail and the cutting edge. Both cutting edges and the sail, which is the turned-up portion opposite of the cutting edge, contribute to a good quality of cut.
Correcting a Mower-Deck Mismatch If there is mismatch between the blades, on a single mower deck, the grass will appear streaked when it is cut. This problem can be corrected by ensuring that the blades are straight and all of the blades are cutting on the same plane. 1. Park the machine on a level surface of the shop floor. 2. Raise the height of cut to the highest position; refer to Adjusting the Height of Cut (page 23). 3.
Storage Preparing for Seasonal Storage Traction Unit 1. Thoroughly clean the traction unit, mower decks, and the engine. 2. Check the tire pressure; refer to Checking the Tire Pressure (page 21). 3. Check all fasteners for looseness; tighten as necessary. 4. Grease or oil all grease fittings and pivot points. Wipe up any excess lubricant. 5. Lightly sand and use touch-up paint on painted areas that are scratched, chipped, or rusted. Repair any dents in the metal body. 6.
Notes: 61
Notes: 62
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
