Form No. 3397-633 Rev A Groundsmaster® 4010 Rotary Mower Model No. 30635—Serial No. 316000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. Figure 2 1. Safety-alert symbol Introduction This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
Mower Maintenance ...................................................58 Pivoting (Tilting) the Front Mower Deck to the Upright Position .................................................58 Pivoting the Front Mower Deck Down ......................58 Adjusting the Mower-Deck Pitch ..............................59 Servicing the Caster-Arm Bushings ...........................59 Servicing the Caster Wheels and Bearings...................60 Blade Maintenance .....................................................
Sound Power Level Safety This unit has a guaranteed sound power level of 104 dBA, which includes an Uncertainty Value (K) of 1 dBA. This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. Sound power level was determined according to the procedures outlined in ISO 11094. Improper use or maintenance by the operator or owner can result in injury.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7272 1. Cutting/dismemberment hazard; fan—stay away from moving parts. 100-5623 1. Low height-of-cut adjustment 2. High height-of-cut adjustment 93-7275 1. Read the Operator's Manual. 2. Do not use starting aids. 100-5624 1. Height-of-cut adjustment 93-7818 1.
106-6754 100-5694 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 1. Height-of-cut adjustment 100-6578 1. Entanglement hazard, belt—do not operate the machine with the shields or guards removed; always keep the shields and guards in place; stay away from moving parts. 106-6755 1. Engine coolant under pressure. 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator's Manual. 4.
114-0846 4. Pull the knob out to 1. Read the Operator’s engage the PTO. Manual for information on starting the engine—1) Set to neutral; 2) Engage the brake; 3) Set the engine speed to slow; 4) Turn the ignition key to preheat; 5) Turn the ignition key to engine start. 2.
120-4159 1. Off 2. Lights 3. On 4. Light-switch location 120-4130 1. Read the Operator’s Manual. 2. To engage the parking brake—1) Lock the pedals together; 2) Push down on the brake; 3) Pull out the parking brake knob. 3. Parking brake 8. High 9. Traction drive 10. Low 11. Power takeoff (PTO) 5. Fast 12. Lower, left deck 6. Variable-speed adjustment 13. Lower, center deck 4. To disengage the parking brake, push down on the brake pedal. 7. Slow 14. Lower, right deck 120-6604 1.
125-9688 121-1599 1. Windshield wipers—off 3. Windshield wipers—on 2. Windshield wipers 4. Spray windshield washer fluid 1. Read the Operator’s Manual for information on fuses. 127-3700 121-3884 1. Engine—stop 1. Raise the left deck 4. Lock the engine speed 2. Raise the center deck 5. Unlock the engine speed 3. Raise the right deck 3. Engine—start 2. Engine—preheat 121-3887 1. Read the Operator’s Manual.
130-5356 1. Use the foot pedal to move forward or in reverse. 132-3600 1. Read the Operator's Manual for more information on fuses. 2. Headlight—25 A 3. Condenser fan and A/C clutch—30 A 4. Fan—25 A 130-0594 5. Working light—20 A 6. Auxiliary power—15 A 7. Cab light—15 A 8. Windshield wipers—15 A 1. Warning—read the Operator’s Manual; when sitting in the cab, always wear a seat belt; wear hearing protection. 130-0611 Battery Symbols Some or all of these symbols are on your battery. 1.
7-2754 1. Warning—read the Operator's Manual. 2. Warning—do not operate this machine unless you are trained. 3. Warning—wear the seat belt when seated in the operator's position. 4. Warning—wear hearing protection. 5. Thrown object hazard—keep bystanders a safe distance from the machine. 6. Cutting hazard of hand or foot—stay away from moving parts; keep all guards in place. 7. Tipping hazard—lower the cutting unit when driving down slopes; slow machine before turning, do not turn at high speeds 8.
1-8378 1. Fan—off 3. Cold air 5. External air 7. Air conditioner—off (If equipped) 2. Fan—on full 4. Hot air 6. Internal air 8.
0-6046 1. Read the Operator’s Manual.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 Use Qty. No parts required – Grease the machine. Warning decal 1 Replace the warning decal. No parts required – Check the tire pressure. No parts required – Check the fluid levels. Media and Additional Parts Description Use Qty.
Product Overview 3 Controls Checking the Tire Pressure Note: Determine the left and right sides of the machine from the normal operating position. No Parts Required Procedure Check the tire pressure; refer to Checking the Tire Pressure (page 24). 9 4 Checking the Fluid Levels No Parts Required 10 g020756 Figure 3 Procedure 1. Check the engine-oil level; refer to Checking the Engine-Oil Level (page 44). 2. Check the hydraulic fluid level; refer to Checking the Hydraulic Fluid (page 55). 3.
Parking-Brake Latch PTO Switch A knob on the left side of the console actuates the parking-brake lock (Figure 3). The PTO switch has 2 positions: OUT (START) and IN (STOP). Pull the PTO button out to engage the mower-deck blades. Push the button in to disengage the mower-deck blades (Figure 4). To engage the parking brake, connect the pedals with the locking latch, push down on both pedals, and pull the parking-brake latch out.
Power-Point Port Weight-Adjustment Lever The power-point port is used to power optional electrical accessories (Figure 5). Use this lever to adjust to the proper weight of the operator (Figure 6). Pull up the lever to increase the air pressure and push down to decrease the air pressure. The proper adjustment is correct when the weight gauge is in the green region.
Air Conditioning Switch 1 Use this switch to turn the air conditioning on or off (Figure 7). TORO Windshield Latch Lift up the latches to open the windshield (Figure 8). Press in the latch to lock the windshield open. Pull out and down on the latch to close and secure windshield. 4 2 3 g020650 Figure 9 1. Indicator light 3. Middle button 2. Right button 4. Left button • Left Button, Menu Access/Back Button—press this button to access the InfoCenter menus.
InfoCenter Icon Description (cont'd.) InfoCenter Icon Description (cont'd.
Using the Menus Glowplugs To access the InfoCenter menu system, press the menu access button while at the main screen. This will bring you to the main menu.
Protected Menus Setting the Maximum Allowed Transport Speed There are 4 operating configuration settings that are adjustable within the Settings Menu of the InfoCenter: auto idle time delay, maximum mowing ground speed, maximum transport ground speed, and Smart Power. These settings are in the Protected Menu. 1. In the Settings Menu, scroll down to Transport Speed and press the right button. 2. Use the right button to increase the max transport speed (50%, 75%, or 100%). 3.
Fuel Safety Operation DANGER Before Operation In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Before Operation Safety General Safety • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills. • Never allow children or untrained people to operate or • Never fill the fuel tank inside an enclosed trailer. service the machine.
Checking the Engine-Oil Level Biodiesel Ready Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 44). This machine can also use a biodiesel blended fuel of up to B20 (20% biodiesel, 80% petrodiesel). The petrodiesel portion should be low or ultra-low sulfur.
Checking the Tire Pressure Checking the Torque of the Wheel-Lug Nuts Service Interval: Before each use or daily Service Interval: After the first hour DANGER After the first 10 hours Low tire pressure decreases machine side-hill stability. This could cause a rollover, which may result in personal injury or death. Every 200 hours Torque the wheel-lug nuts to 115 to 136 N∙m (85 to 100 ft-lb) in the order shown in Figure 12 and Figure 13. Do not underinflate the tires.
Adjusting the Height of Cut Front Mower Deck The height of cut is adjustable from 25 to 127 mm (1 to 5 inches) in 13 mm (1/2 inch) increments. To adjust the height of cut on the front mower deck, position the caster-wheel axles in the upper or lower holes of the caster forks, add or remove an equal number of spacers from the caster forks, and secure the rear chain to the desired hole. Figure 15 1. Start the engine and raise the mower decks to change height of cut. 6.
Wing Mower Decks 5. Remove the hairpin cotter and clevis pins from the caster-pivot arms (Figure 20). To adjust the height of cut on the wing mower decks, add or remove an equal number of spacers from the caster forks, position the caster-wheel axles in the high or low height-of-cut holes in the caster forks, and secure the pivot arms to the selected height-of-cut bracket holes. 1. Position the caster-wheel axles in the same holes in all of the caster forks (Figure 18 and Figure 20). 2.
Adjusting the Skids Mount the skids in the lower position when operating at heights of cut greater than 64 mm (2-1/2 inches) and in the higher position when operating at heights of cut lower than 64 mm (2-1/2 inches). Note: When the skids become worn, you can switch them to the opposite sides of the mower by flipping them over. This allows you to use the skids longer before replacing them. Adjust the skids (Figure 24). Important: Torque the screw at the front of each skid to 9 to 11 N∙m (80 to 100 in-lb).
Adjusting the Mower-Deck Rollers 9. Lower the mower decks onto a flat surface and remove the covers from the top of the mower decks. 10. Loosen the flange nut, securing the idler pulley, to release the belt tension on each mower deck. The mower-deck rollers should be mounted in the lower position when operating at height of cuts greater than 64 mm (2-1/2 inches) and in the higher position when operating in height of cuts lower than 64 mm (2-1/2 inches). 1.
Setting up the Wing Mower Decks remove a 3 mm (1/8 inch) shim from the bottom of the front, inside caster arm on the wing mower deck (Figure 27). 1. Rotate the blade of each spindle until the ends face forward and backward. Note: Check the measurements between the outside edges of both wing mower decks and the inside edge of the wing mower deck to the outside edge of the front mower deck again. 2. Measure from the floor to the front tip of the cutting edge. 3.
During Operation not engage. If the PTO engages, there is a malfunction in the interlock system that should be corrected before beginning operation. During Operation Safety 4. Sit on the seat, engage the parking brake and start the engine. Move the traction pedal out of the NEUTRAL position. The InfoCenter will display “traction not allowed” and the machine should not move. If the engine does move, there is a malfunction in the interlock system that should be corrected before beginning operation.
• Avoid turning the machine on slopes. If you must turn, • Reduce the throttle setting before stopping the engine turn slowly and gradually downhill, if possible. and, if the engine has a fuel-shutoff valve, shut off the fuel when you have finished operating the machine. • Use extra care while operating the machine with • Never run an engine in an area where exhaust gases are attachments; they can affect the stability of the machine.
Stopping the Engine Using Cruise Control Important: Allow the engine to idle for 5 minutes before shutting it off after a full-load operation. This allows the turbocharger to cool down before shutting the engine off. Failure to do so may damage the turbocharger. The cruise-control switch locks in the pedal position to maintain the desired ground speed.
When in the InfoCenter splash or main screen, press the middle button ( icon) to adjust the speed. Note: When switching between low and high ranges, the settings will transfer based on the previous setting. The settings are reset when the machine is turned off. Note: This feature may also be used in conjunction with cruise control.
Pushing or Towing the Machine In an emergency, you can move the machine by actuating the bypass valve in the variable-displacement hydraulic pump and pushing or towing the machine. Important: Do not push or tow the machine faster than 3 to 4.8 km/h (2 to 3 mph), because internal-transmission damage may occur. The bypass valves must be open whenever you push or tow the machine. 1. Raise the seat and locate the bypass valves, which are located below the front of the fuel tank (Figure 31). Figure 30 1.
Locating the Jacking Points Locating the Tie-Down Points There are tie downs located at the front and rear sides of the machine (Figure 32). WARNING Always use jack stands. Do not rely on a jack or hoist to hold the machine. Note: Use properly-rated DOT-approved straps in 4 corners to tie down the machine. Mechanical or hydraulic jacks may fail to support the machine and cause a serious injury.
Maintenance Note: Download a free copy of the schematic by visiting www.Toro.com and searching for your machine from the Manuals link on the home page. Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour Maintenance Procedure • Torque the wheel-lug nuts. After the first 10 hours • • • • Torque the wheel-lug nuts. Check the alternator-belt tension.
Maintenance Service Interval Every 800 hours Maintenance Procedure • • • • • • • • • Drain and clean the fuel tank (also if the fuel system is contaminated). Change the front planetary-gear oil. Change the rear-axle lubricant. Check the rear wheel toe-in. Inspect the blade-drive belt. Change the hydraulic fluid. Change the hydraulic filters. Inspect the wing mower-deck damper. Inspect the mower deck caster-wheel assemblies. Every 1,000 hours • Check and adjust the engine-valve clearance.
For the week of: Maintenance Check Item Monday Tuesday Wednesday Thursday Friday Saturday Check the height-of-cut adjustment. Lubricate all the grease fittings.2 Touch up any damaged paint. 1Check the glow plug and injector nozzles if starting is hard, there is excess smoke, or rough running is noted. 2Immediately after every washing, regardless of the interval listed. Important: Refer to your engine operator’s manual for additional maintenance procedures.
Service Interval Chart Figure 33 Premaintenance Procedures 5. Engage the parking brake. 6. Move the throttle switch to the LOW -IDLE position. 7. Shut off the engine and remove the key. 8. Wait for all moving parts to stop. Pre-Maintenance Safety • Whenever you park or store the machine, or leave it • Keep all parts of the machine in good working condition • • and all hardware tightened, especially blade-attachment hardware. Replace all worn or damaged decals.
Lubrication • Use jack stands to support the machine and/or its components when required. • Carefully release pressure from components with stored Greasing the Bearings and Bushings energy. • If your machine requires major repairs or if you desire assistance, contact an Authorized Toro Distributor. Service Interval: Every 50 hours (lubricate after every washing). • Use only genuine Toro replacement parts and accessories.
g017810 Figure 39 Front Lift Assemblies • 2 (each side) lift-arm-cylinder bushings (Figure 40) • 2 lift-arm-ball joints (Figure 41) Figure 37 Front Mower Deck Figure 40 • 2 caster-fork-shaft bushings (Figure 38) • 3 spindle-shaft bearings—located under the pulley (Figure 39) • 2 idler-arm-pivot bushings (Figure 39) Figure 41 Figure 38 41
Wing Mower Decks • 1 caster-fork-shaft bushing (Figure 42) • 2 (each side) spindle-shaft bearings—located under the pulley • 1 idler-arm-pivot bushings—located on the idler arm Figure 44 Figure 42 Figure 45 Side Lift Assemblies • 6 main lift-arm bushings (Figure 43 and Figure 44) • 2 bell-crank-pivot bushings (Figure 45) • 4 rear arm bushings (Figure 45) • 4 lift-cylinder bushings (Figure 46) Figure 46 Figure 43 42
Engine Maintenance Engine Safety Shut off the engine before checking the oil or adding oil to the crankcase. Servicing the Air Cleaner Service Interval: Before each use or daily—Check the air-cleaner indicator Every 50 hours—Inspect the air cleaner. Every 400 hours—Service the air cleaner (earlier if the air cleaner indicator shows red, and more frequently in extremely dirty or dusty conditions). Check the air-cleaner body for damage, which could cause an air leak. Replace it if it is damaged.
Figure 49 1. Air-cleaner safety filter 2. Reset the indicator (Figure 47) if it shows red. Checking the Engine-Oil Level Service Interval: Before each use or daily The engine is shipped with oil in the crankcase; however, the oil level must be checked before and after the engine is first started. Figure 50 The crankcase capacity is approximately 5.7 L (6 US qt) with the filter. Note: When using different oil, drain all old oil from the crankcase before adding new oil.
Changing the Engine Oil and Filter Fuel System Maintenance Service Interval: Every 250 hours 1. Start the engine and let it run 5 minutes to allow the oil to warm up. Servicing the Fuel System 2. Park the machine on a level surface, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Draining the Fuel Tank Service Interval: Every 800 hours (also if the fuel system is contaminated). 3. Replace the engine oil and filter (Figure 51).
Servicing the Water Separator Electrical System Maintenance Service Interval: Before each use or daily—Drain water or other contaminants from the water separator. Electrical System Safety Every 400 hours • Disconnect the battery before repairing the machine. Service the water separator as shown in Figure 52. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Battery acid is poisonous and can cause burns.
Servicing the Battery WARNING Battery terminals or metal tools could short against metal components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Service Interval: Every 25 hours—Check the electrolyte level (or every 30 days if the machine is in storage). Every 50 hours—Check the condition of the battery. Important: Before welding on the machine, disconnect the negative cable from the battery to prevent damage to the electrical system.
Locating the Fuses The traction-unit fuses are located under the power-center cover (Figure 55, Figure 56, and Figure 57). Remove the 2 screws securing the power-center cover to the frame and remove the cover (Figure 55). Figure 58 1. Cab fuse box 2. Fuses Figure 55 1. Power-center cover 2. Screws Figure 59 Figure 56 1. Fuses Figure 57 The cab fuses are located in the fuse box in the cab headliner (Figure 58 and Figure 59).
Drive System Maintenance Note: The oil level should be at the bottom of the check-plug hole. 3. If the oil level is low, remove the plug at the 12 o’clock position and add oil until it begins to flow out of the hole at the 3 o’clock position. Adjusting the Traction-Pedal Angle 4. Install both plugs. 1. Loosen the 2 nuts and bolts securing the left side of the traction pedal to the bracket (Figure 60).
Checking the Rear-Axle-Gearbox Lubricant 6. Through the open hole, slowly fill the planetary with 0.65 L (22 oz) of high quality SAE 85W-140 wt gear lube. Service Interval: Every 400 hours Important: If the planetary fills before the 0.65 L (22 oz) of oil is added, wait 1 hour or install the plug and move the machine approximately 10 feet to distribute the oil through the brake system. Then, remove the plug and add the remaining oil. The gearbox is filled with SAE 85W-140 gear lube. The capacity is 0.
Checking the Rear Wheel Toe-In Service Interval: Every 800 hours 1. Measure the center-to-center distance (at axle height) at the front and rear of the steering tires. Note: The front measurement must be 6 mm (1/4 inch) less than the rear measurement. 2. To adjust, loosen the clamps at both ends of the tie rods. 3. Rotate the tie-rod end to move the front of the tire inward or outward. Figure 66 1. Drain-plug location 4. Tighten the tie-rod clamps when the adjustment is correct. 5.
Cooling System Maintenance Important: Do not use water only or alcohol/methanol base coolants, as this may cause damage. 4. Install the radiator cap and expansion-tank cap. Cooling System Safety Servicing the Engine-Cooling System CAUTION Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. • Do not remove the radiator cap when the engine is hot.
Brake Maintenance Adjusting the Service Brakes Adjust the service brakes when there is more than 25 mm (1 inch) of “free travel” of the brake pedal, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before you feel braking resistance. 1. Disengage the locking latch from the brake pedals so that both pedals work independently of each other. 2. To reduce free travel of the brake pedals, tighten the brakes as follows: A.
Belt Maintenance Tensioning the Blade-Drive Belts Servicing the Alternator Belt Service Interval: After the first 10 hours Every 50 hours Service Interval: After the first 10 hours When properly tensioned, the inside measurement of the extension spring (hook to hook) should be approximately 8.3 to 9.5 cm (3-1/4 to 3-3/4 inches). Once the correct spring tension is attained, adjust the stop bolt (carriage bolt) until there is approximately 2 to 5 mm (0.065 to 0.
Hydraulic System Maintenance Note: If the stop bolt is ever removed from the mounting tab, make sure that it is installed again in the hole that aligns the stop-bolt head with the idler arm. 4. Remove the bolts securing the hydraulic motor to the mower deck (Figure 74). Hydraulic System Safety WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 Material Properties: Viscosity, ASTM D445 St @ 40° C 44 to 48 St @ 100° C 7.9 to 8.
Changing the Hydraulic Fluid Replacing the Hydraulic Filters Service Interval: Every 800 hours Service Interval: After the first 200 hours Every 800 hours Change the hydraulic fluid after every 800 operating hours, in normal conditions. If the fluid becomes contaminated, contact your local Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. Use Toro replacement filters Part No.
Mower Maintenance Adjusting the Counterbalance Pressure Pivoting (Tilting) the Front Mower Deck to the Upright Position The counterbalance test port is used to test the pressure in the counterbalance circuit (Figure 78). The recommended counterbalance pressure is 2,241 kPa (325 psi). To adjust the counterbalance pressure, loosen the locknut, rotate the adjusting screw (Figure 78) clockwise to increase the pressure, or counterclockwise to decrease the pressure and tighten the locknut.
Adjusting the Wing Mower-Deck Pitch 4. Sit on the seat, start the engine, and lower the mower deck until it is slightly off the floor. Service Interval: Every 800 hours 5. Secure the height-of-cut chains to the rear of the mower deck. 1. Remove the tensioning cap from the spindle shaft and slide the spindle out of the caster arm (Figure 81). 6. Pivot the transport latch upward into position and secure it with the clevis pin and cotter pin.
Figure 82 1. Caster-arm tube 2. Bushings Figure 84 5. Apply grease to the inside and outside of the new bushings. 6. Using a hammer and flat plate, drive the bushings into the mounting tube. 5. To assemble the caster wheel, push the bearing into the wheel hub. Servicing the Caster Wheels and Bearings Note: When installing the bearings, press on the outer face of the bearing. 6.
Blade Maintenance Removing and Installing the Mower Blade(s) Blade Safety The blade must be replaced if a solid object is hit, the blade is out of balance, or if the blade is bent. Always use genuine Toro replacement blades to ensure safety and optimum performance. DANGER A worn or damaged blade can break, and a piece of the blade could be thrown at you or bystanders, resulting in serious personal injury or death.
1. Position the machine on a level surface, raise the mower deck, engage the parking brake, put the traction pedal in NEUTRAL, put the PTO lever in the OFF position, shut off the engine, and remove the ignition key. 2. Examine the cutting ends of the blade carefully, especially where the flat and curved parts of the blade meet (Figure 87). Figure 88 Note: Because sand and abrasive material can wear away the metal that connects the flat and curved parts of the blade, check the blade before using the mower.
Cab Maintenance of the mower deck. Continue to check the alignment of the blades and add shims until the tips of the blades are within the required dimension. Cleaning the Cab Air Filters Important: Do not use more than 3 shims at any 1 hole location. Use decreasing numbers of shims in adjacent holes if more than 1 shim is added to any 1 hole location. Service Interval: Every 250 hours 1. Remove the screws and grates from both the in-cab and rear cab air filters (Figure 89 and Figure 90). 8.
Storage Important: If either filter has a hole, tear, or other damage, replace the filter. 3. Install the filters and the grate with the thumb screws. Preparing for Seasonal Storage Cleaning the Air-Conditioning Assembly Traction Unit Service Interval: Every 250 hours (more frequently in extremely dusty or dirty conditions). 1. Thoroughly clean the traction unit, mower decks, and the engine. 1. Perform the pre-maintenance procedure; refer to Preparing the Machine for Maintenance (page 40). 2.
Notes: 65
Notes: 66
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
