Installation Instructions

ManualsBrandsToro ManualsAttachmentsEU Light Kit, 2015 Groundsmaster 5910 Series Rotary Mower with Cab

FormNo.3392-727RevA

EULightKit

2015andAfterGroundsmaster

5910SeriesRotaryMowerwith

Cab

ModelNo.30639

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Disconnectthebattery.

Flasherbracket1

Flangeheadscrew,1/4x1/2inch

Flangenut,1/4inch

Flashermodule1

wiringharness1

Installtheashermodule.

Switch,hazard

Cabletie

Installthesignalcontrollerandhazard

switch.

Headlampbracket,lefthand(formodel

withoutcab)

Headlampbracket,righthand(formodel

withoutcab)

Headlampbracket,righthand(formodel

withcab)

Headlampbracket,lefthand(formodel

withcab)

Headlamprighthand1

Headlamplefthand

Flangeheadbolt,1/21–1/4inch

Flangenut,1/2inch

Headlightwiringcover(formodel

withoutcab)

Plasticplug8

Cableties

Installtheheadlights.

Fuse,10amp1

Fuseblock1

Decal,turnsignalfuse

Installthefuseblock.

Rearlampassembly2

Cabletiemount

Cabletie

Installtherearlamps.

MediaandAdditionalParts

Description

Qty.

Use

Partscatalog1

Installationinstructions1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3392-727*A

Summary of content (12 pages)

PAGE 1
Form No. 3392-727 Rev A EU Light Kit 2015 and After Groundsmaster® 5910 Series Rotary Mower with Cab Model No. 30639 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 5 6 Use Qty.
PAGE 2
1 Disconnecting the Battery No Parts Required Procedure 1. Position the machine on a level surface, set the parking brake, lower the cutting units, turn the ignition off, and remove the key. CAUTION Figure 1 If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or bystanders. 1. Steering tower cover 2. Mounting screw 2. Mount the flasher module to the bracket with a #10 x 5/8 inch screw 2 flat washers (0.216 x 0.
PAGE 3
Figure 3 3
PAGE 4
3 4 Installing the Hazard Switch Installing the Headlights Parts needed for this procedure: Parts needed for this procedure: 1 Switch, hazard 1 Headlamp bracket, left hand (for model without cab) 2 Cable tie 1 Headlamp bracket, right hand (for model without cab) 1 Headlamp bracket, right hand (for model with cab) 1 Headlamp bracket, left hand (for model with cab) 1 Headlamp right hand 1 Headlamp left hand 2 Flange head bolt, 1/2 1–1/4 inch 2 Flange nut, 1/2 inch 2 Headlight wiring
PAGE 5
supplied with the lights. Make sure the turn signal lens on the headlight is positioned toward the outside of the machine. 5. Route the headlight wiring harness ends underneath the front edge of the operator's platform, thru the headlight brackets and to the headlights (Figure 3). 6. Plug one of the harness connectors into the previously unplugged harness connector and one into the headlight. The headlight connection should be made inside the headlight bracket. Repeat this procedure on the other headlight.
PAGE 6
7 g028605 Figure 9 g028606 1. Flange head bolt, 1/4 x 3/4 5. Flange nut, 1/4 inch inch 2. Cab bracket 6. Cable ties 3. Flange nut, 1/2 inch 7. Flange head bolt, 1/2 x 1-1/4 inch 4. Headlight assembly, left hand Figure 10 1. Headlight assembly, right hand 2. Headlight bracket, right hand 3. Flange head bolt, 1/4 x 3/4 inch 4. Cab bracket 4. Loosely mount the end of the headlight bracket to the side of the cab bracket with a 1/4 x 3/4 inch flange head bolt and 1/4 inch flange nut (Figure 9). 5.
PAGE 7
5 Installing the Fuse Block Parts needed for this procedure: 1 Fuse, 10 amp 1 Fuse block 1 Decal, turn signal fuse Procedure 1. Affix and connect the new fuse block to the existing fuse blocks (Figure 11). This may not necessary if a new fuse block was previously installed for another attachment. Note: The 2 screws and nuts from the adjoining fuse block may be removed and reused to secure the new fuse block to the machine. 2. Insert the 10 amp fuse into the open slot on the fuse block (Figure 11).
PAGE 8
Figure 13 1. Rear bumper bracket bolts and nuts Figure 15 2. Using the bolts and nuts previously removed, secure a lamp assembly to the bracket and frame (Figure 14). 1 2 1. Hood support bracket 4. Radiator hose 2. Valve 3. Radiator support 5. Frame shroud • Affix a cable tie mounting pad to the under side of the frame, behind the rear axle and approximately 7 inches (17.8 cm) from the right frame rail (Figure 16).
PAGE 9
Figure 17 1. Hood support frame 3. Muffler heat shield 2. Corner shroud 4. Radiator support • Over the hard lines down through the frame (Figure 17). • Affix a cable tie mounting pad to the under side of the frame, behind the rear axle and approximately 7 inches (17.8 cm) from the left frame rail (Figure 16). • Secure the harness to the mounting pad with a cable tie.
PAGE 10
7 Connecting the Battery No Parts Required Procedure 1. Connect the negative battery cable to both batteries. 2. Install the access panel. Operation Using the Light and Hazard Switches • Turn the key switch ON and press the light switch to the ON position to activate the head lamps. • Press the hazard switch to the On position to activate the front and rear flashing hazard lights.
PAGE 11
Schematics Electrical Schematic (Rev.
PAGE 12