Form No. 3400-151 Rev A Groundsmaster® 4110 Rotary Mower Model No. 30643—Serial No. 316000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. 1 WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. g028455 Figure 1 1.
Contents Locating the Tie-Down Points..................................39 Maintenance .................................................................40 Recommended Maintenance Schedule(s) ......................40 Daily Maintenance Checklist ....................................41 Service Interval Chart .............................................42 Premaintenance Procedures ........................................43 Pre-Maintenance Safety...........................................
Safety Replacing the Mower-Deck-Hinge Covers .................64 Blade Maintenance .....................................................65 Blade Safety...........................................................65 Checking for a Bent Blade........................................65 Removing and Installing the Mower Blade(s) ..............65 Inspecting and Sharpening the Mower Blade(s) .............................................................65 Correcting a Mower-Deck Mismatch.........................
Sound Power Level This unit has a guaranteed sound power level of 104 dBA, which includes an Uncertainty Value (K) of 1 dBA. Sound power level was determined according to the procedures outlined in ISO 11094. Sound Pressure Level This unit has a sound pressure level at the operator’s ear of 85 dBA, which includes an Uncertainty Value (K) of 1 dBA. Sound pressure level was determined according to the procedures outlined in EN ISO 5395:2013.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7818 1. Warning—read the Operator's Manual for instructions on torquing the blade bolt/nut to 115-149 N-m (85-110 ft-lb). 106-4250 1. Height-of-cut 100-5622 1. Height-of-cut adjustment 106-4251 1. Height-of-cut 100-5623 1. Low height-of-cut adjustment 2. High height-of-cut adjustment 104-3579 1.
117–2754 1. Warning—read the Operator's Manual. 2. Warning—do not operate this machine unless you are trained. 3. Warning—wear the seat belt when seated in the operator's position. 4. Warning—wear hearing protection. 5. Thrown object hazard—keep bystanders a safe distance from the machine. 6. Cutting hazard of hand or foot—stay away from moving parts; keep all guards in place. 7. Tipping hazard—lower the cutting unit when driving down slopes; slow machine before turning, do not turn at high speeds 8.
93-7275 1. Read the Operator's Manual. 2. Do not use starting aids. 120–4159 106-6754 1. Off 2. Lights 1. Warning—do not touch the hot surface. 3. On 4. Light switch location 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 8. High 9. Traction drive 10. Low 11. Power take-off (PTO) 5. Fast 12. Lower left deck 6. Variable-speed adjustment 13. Lower center deck 7. Slow 14. Lower right deck 100-6578 1.
117–2718 93-7272 1. Cutting/dismemberment hazard; fan—stay away from moving parts. 127–3700 1. Raise left deck 4. Lock engine speed 2. Raise center deck 5. Unlock engine speed 3. Raise right deck 93-6674 1. Crushing hazard, hand—read the instructions before servicing or performing maintenance. 106-6755 1. Engine coolant under pressure. 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator's Manual. 4. Warning—read the Operator's Manual. 120–4129 9 1. Beacon 3.
120–4130 1. Read the Operator’s Manual. 2. To engage the parking brake—1) Lock the pedals together; 2) Push down on the brake; 3) Pull out the parking brake knob. 114–0849 3. Parking brake 4. Forward direction 1. Warning—1) Disengage the PTO; 2) Raise the deck 4. To disengage the parking brake, push down on the brake pedal. 2. Do not place your foot here. 3. Direction pedal 5. Reverse direction 114–0845 1. Steering-wheel-tilt lever 121–1599 1. Read the Operator’s Manual for information on fuses.
4–0846 4. Pull the knob out to 1. Read the Operator’s engage the PTO. Manual for information on starting the engine—1) Set to neutral; 2) Engage the brake; 3) Set the engine speed to slow; 4) Turn the ignition key to preheat; 5) Turn the ignition key to engine start. 2.
1-8378 1. Fan—off 3. Cold air 5. External air 7. Air conditioner—on (If equipped) 2. Fan—on full 4. Hot air 6. Internal air 8. Air conditioner—off (If equipped) 125-9688 1. Windshield wipers—off 3. Windshield wipers—on 2. Windshield wipers 4.
0-5357 1. Push forward to move forward. 2. Push back to reverse. 130-5733 1. Attention; read the Operator's Manual—1) Remove the optional trash bag; 2) Tilt the seat forward. 130-0594 130-5980 1. Warning—read the Operator’s Manual; when sitting in the cab, always wear a seat belt; wear hearing protection. 1. Attention; read the Operator's Manual—To leave the machine: 1) Lower the cutting deck; 2) Leave the machine. 130-0611 1. Warning—1) Remove the pin; 2) Raise the doors; 3) Exit the cab.
GROUNDSMASTER 4110, MODEL 30643 & 30644 QUICK REFERENCE AID 7 3 11 I 11 6 A 1 E F 8 B H G 5 4 C 2 11 D 11 9 CHECK/S ERVICE (DAILY) 1. ENGINE OIL LEVEL 2. HYDRAULIC FLUID LEVEL 3. ENGINE COOLANT LEVEL 4. FUEL - DIESEL ONLY 5. FUEL/WATER SEP ARATOR 6. FAN BELT TENSION 7. RADIATOR SCREEN 8. AIR CLEANER 9. BRAKE FUNCTION 10. INTERLOCK SYSTEM 11. TIRE PRESSURE - 25 PSI/1.70 BAR 12. GREASE POINTS (4) SEE OPERATOR'S MANUAL FOR 50 HR INTERVAL GREASE POINTS.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 Use Qty. No parts required – Grease the machine. Warning decal 1 Replace the warning decal. No parts required – Check the tire pressure. No parts required – Check the fluid levels. Media and Additional Parts Description Use Qty.
Product Overview 3 Controls Checking the Tire Pressure Note: Determine the left and right sides of the machine from the normal operating position. No Parts Required Machine Controls Procedure Check the tire pressure; refer to Checking the Tire Pressure (page 24). 9 Important: Maintain pressure in all tires to ensure a good quality-of-cut and proper machine performance. Do not underinflate the tires. 4 Checking the Fluid Levels 10 g020756 Figure 3 No Parts Required Procedure 1.
Parking-Brake Latch PTO Switch A knob on the left side of the console actuates the parking-brake lock (Figure 3). The PTO switch has 2 positions: OUT (START) and IN (STOP). Pull the PTO button out to engage the mower-deck blades. Push the button in to disengage the mower-deck blades (Figure 4). To engage the parking brake, connect the pedals with the locking latch, push down on both pedals, and pull the parking-brake latch out.
Cab Controls Seat Controls 4 Seat-Adjustment Lever 5 Move the seat-adjustment lever on the side of the seat outward, slide the seat to the desired position, and release the lever to lock the seat into position (Figure 6). 3 6 2 1 8 9 g028431 7 Figure 7 1. Air-recirculation control 2. Fan control 2. Weight-adjustment lever 3. Temperature control 7. Flashers switch 4. Windshield-wiper switch 8. Air-conditioning switch Air Recirculation Control Figure 6 1. Weight gauge 5. Power outlet 6.
Air-Conditioning Switch Use this switch to turn the air conditioning on or off (Figure 7). Wind Shield Latch Lift up the latches to open the windshield (Figure 8). Press in the latch to lock windshield to the OPEN position. Pull out and down on the latch to close and secure the windshield. Figure 8 1. Windshield latch Rear Window Latch Lift up the latches to open the rear window. Press in the latch to lock the window in the OPEN position.
Specifications Figure 9 20
Description Height with cab Figure 9 reference Dimension or Weight A 237 cm (93.
Fuel Safety Operation DANGER Note: Determine the left and right sides of the machine from the normal operating position. In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Before Operation • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills. Before Operation Safety • Never fill the fuel tank inside an enclosed trailer.
Checking the Engine-Oil Level • The biodiesel portion of the fuel must meet specification Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 47). • The blended fuel composition should meet ASTM D975 ASTM D6751 or EN14214. or EN590. • Painted surfaces may be damaged by biodiesel blends.
Checking the Tire Pressure Checking the Torque of the Wheel-Lug Nuts Service Interval: Before each use or daily Service Interval: After the first hour DANGER After the first 10 hours Low tire pressure decreases machine side-hill stability. This could cause a rollover, which may result in personal injury or death. Every 200 hours WARNING Do not underinflate the tires. Failing to maintain proper torque of the wheel-lug nuts could result in personal injury.
Adjusting the Mirrors 1. Start the engine and raise the mower decks to change height-of-cut. Cab model only 2. Shut off the engine and remove the key after the mower deck is raised. Rear View Mirror 3. Position the caster-wheel axles in the same holes in all caster forks. While sitting in the seat, adjust the rear view mirror (Figure 14) to attain the best view out the rear window. Pull the lever rearward to tilt the mirror to reduce the brightness and glare of light.
Note: When using 25 mm (1 inch), 38 mm (1-1/2 inch), or occasionally 51 mm (2 inch) height-of-cut, move the skids and gage wheels to the highest position. Wing Mower Decks To adjust the height-of-cut on the wing mower decks, add or remove an equal number of spacers from the caster forks, position the caster-wheel axles in the high or low height-of-cut holes in the caster forks, and secure the pivot arms to the selected height-of-cut bracket holes. Figure 16 6.
Adjusting the Skids Mount the skids in the lower position when operating at heights of cut greater than 64 mm (2-1/2 inches) and in the higher position when operating at heights of cut lower than 64 mm (2-1/2 inches). Figure 20 4. Push the caster spindle through the front caster arm. 5. Install the shims (as they were originally installed) and the remaining spacers onto the spindle shaft. 6. Remove the hairpin cotter and clevis pins from the caster-pivot arms (Figure 21). 7.
Adjusting the Blade Correcting a Mismatch Between Mower Decks To ensure proper operation of the mower deck, there must be a 10 to 16 mm (0.38 to 0.62 inch) clearance between the tips of the side and center mower-deck blades (Figure 25). 1. Raise mower deck so the blades are visible and block the center deck section so it cannot fall accidentally.
Setting up the Center Mower Deck Setting up the Wing Mower Decks 1. Rotate the blade on each spindle until the ends face forward and backward. 1. Rotate the blade of each spindle until the ends face forward and backward. 2. Measure from the floor to the front tip of the cutting edge. 2. Measure from the floor to the front tip of the cutting edge. 3.
Using the InfoCenter Control Checking the Safety-Interlock Switches The InfoCenter LCD display shows information about your machine such as the operating status, various diagnostics and other information about the machine (Figure 29). There is a splash screen and main information screen of the InfoCenter. You can switch between the splash screen and main information screen at any time by pressing any of the InfoCenter buttons and then selecting the appropriate directional arrow.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.
InfoCenter Icon Description (cont'd.) Main Menu Settings The Settings menu allows you to customize and modify configuration variables on the InfoCenter display. About The About menu lists the model number, serial number, and software version of your machine. Operator should change to the indicated state Symbols are often combined to form sentences.
Protected Menus Settings Menu Item Description Units Controls the units used on the InfoCenter; the menu choices are English or Metric Language Controls the language used on the InfoCenter* LCD Backlight Controls the brightness of the LCD display LCD Contrast Controls the contrast of the LCD display Protected Menus Allows the distributor/engineer to access protected menus by inputting a passcode Auto Idle Controls the amount of time allowed before idling the engine when the machine is not in u
Setting the Maximum Allowed Transport Speed During Operation 1. In the Settings Menu, scroll down to Transport Speed and press the right button. During Operation Safety 2. Use the right button to increase the max transport speed (50%, 75%, or 100%). General Safety • The owner/user can prevent and is responsible for 3. Use the center button to decrease the max transport speed (50%, 75%, or 100%). • 4. Press the left button to exit.
Starting and Shutting Off the Engine • Reduce the throttle setting before shutting off the engine and, if the engine has a fuel-shutoff valve, shut off the fuel when you have finished operating the machine. • Never run an engine in an area where exhaust gases are Starting the Engine enclosed. • Never leave a running engine unattended.
Understanding Smart Power™ Traction Using the Engine-Speed Switch With Toro Smart Power™ traction, the operator does not have to listen to the engine speed in heavy conditions. Smart Power prevents bogging down in heavy turf by automatically controlling the machine speed and optimizing cutting performance. The operator can simply set a maximum ground speed, that is comfortable, and mow without having to manually reduce the traction speed when mowing in heavy conditions.
Understanding the Operating Characteristics of the Machine Practice driving the machine because it has a hydrostatic transmission and its characteristics are different than many turf-maintenance machines. Some points to consider when operating the traction unit, mower deck, or other implements, are the transmission, engine speed, load on the mower blades or other implement components, and the importance of the brakes.
After Operating After Operation To ensure optimum performance, clean the underside of the mower housing after each use. If residue builds up in the mower housing, cutting performance decreases. After Operation Safety Also, remove any debris which may have collected between the deck-lift cylinders and the foam-deck pads (Figure 31). General Safety • Clean grass and debris from the cutting units, drives, mufflers, and engine to help prevent fires. Clean up oil or fuel spills.
Locating the Tie-Down Points Note: Do not open more than 3 turns. Because fluid is bypassed, the machine can be slowly moved without damaging the transmission. There are tie downs located at the front and rear sides of the machine (Figure 33). 3. Close the bypass valves before starting the engine. Note: Use properly-rated DOT-approved straps in 4 corners to tie down the machine. 4. Torque to 70 N∙m (52 ft-lb) to close the valve.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour Maintenance Procedure • Torque the wheel-lug nuts. After the first 10 hours • • • • Torque the wheel-lug nuts. Check the alternator-belt tension. Check the compressor belt tension. Check the blade-drive-belt tension. After the first 200 hours • Change the front planetary-gear oil. • Change the rear-axle lubricant.
Maintenance Service Interval Every 800 hours Maintenance Procedure • • • • • • Drain and clean the fuel tank (also if the fuel system is contaminated). Change the front planetary-gear oil. Change the rear-axle lubricant. Check the rear wheel toe-in. Inspect the blade-drive belt. Change the hydraulic fluid. Change the hydraulic fluid after every 800 operating hours, in normal conditions. If the fluid becomes contaminated, contact your local Toro distributor because the system must be flushed.
For the week of: Maintenance Check Item Monday Tuesday Wednesday Thursday Friday Saturday Check the instrument operation. Check the height-of-cut adjustment. Lubricate all the grease fittings.2 Touch up any damaged paint. 1Check the glow plug and injector nozzles if starting is hard, there is excess smoke, or rough running is noted. 2Immediately after every washing, regardless of the interval listed. Important: Refer to your engine operator’s manual for additional maintenance procedures.
Premaintenance Procedures Preparing the Machine for Maintenance 1. Ensure that the PTO is disengaged. 2. Park the machine on a level surface. Pre-Maintenance Safety 3. Set the parking brake. • Keep all parts of the machine in good working condition 4. Lower the mower deck(s) if necessary. and all hardware tightened, especially blade-attachment hardware. Replace all worn or damaged decals. 5. Shut off the engine and wait for all moving parts to stop.
Lubrication Greasing the Bearings and Bushings Service Interval: Every 50 hours The machine has grease fittings that you must lubricate regularly with No. 2 lithium grease. Also, lubricate the machine immediately after every washing.
Figure 40 Figure 41 Figure 42 Center-Deck-Lift Assemblies • 2 (each side) lift-arm-cylinder bushings (Figure 43) • 2 lift-arm ball joints (Figure 44) Figure 44 Figure 43 45
Engine Maintenance Wing-Deck-Lift Assemblies The 4 wing deck-lift cylinder (Figure 45) Engine Safety Shut off the engine before checking the oil or adding oil to the crankcase. Servicing the Air Cleaner Service Interval: Before each use or daily—Check the air-cleaner indicator Every 50 hours—Inspect the air cleaner. Every 400 hours—Service the air cleaner (earlier if the air cleaner indicator shows red, and more frequently in extremely dirty or dusty conditions).
Figure 49 1. Air-cleaner safety filter 2. Reset the indicator (Figure 47) if it shows red. Checking the Engine-Oil Level Service Interval: Before each use or daily The engine is shipped with oil in the crankcase; however, the oil level must be checked before and after the engine is first started. The crankcase capacity is approximately 5.7 L (6 US qt) with the filter. Use high-quality engine oil that meets the following specifications: • API Classification Level Required: CH-4, CI-4, or higher.
Changing the Engine Oil and Filter Service Interval: Every 250 hours 1. Start the engine and let it run 5 minutes to allow the oil to warm up. 2. Park the machine on a level surface, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Replace the engine oil and filter (Figure 51). Figure 50 Note: When using different oil, drain all old oil from the crankcase before adding new oil. Figure 51 4.
Fuel System Maintenance Servicing the Fuel System Draining the Fuel Tank Service Interval: Every 800 hours (also if the fuel system is contaminated). Use clean fuel to flush out the tank. Inspecting the Fuel Lines and Connections Service Interval: Every 400 hours Inspect the fuel lines and connections for deterioration, damage, or loose connections. Servicing the Water Separator Service Interval: Before each use or daily—Drain water or other contaminants from the water separator.
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. Figure 53 • Battery acid is poisonous and can cause burns. Avoid contact with your skin, eyes, and clothing. Protect your face, eyes, and clothing when working with a battery. • Battery gases can explode. Keep cigarettes, sparks, and flames away from the battery.
3. Coat both battery connections with Grafo 112X (skin-over) grease (Toro Part No. 505-47), petroleum jelly, or light grease to prevent corrosion. The cab fuses (Figure 58 and Figure 59) are located in the fuse box in the cab headliner (Cab model only). 4. Slide the rubber boot over the positive terminal. 5. Close the battery cover. Fuses The traction unit fuses (Figure 55 thru Figure 57) are located under the power-center cover.
Drive System Maintenance Note: The oil level should be at the bottom of the check-plug hole. 3. If the oil level is low, remove the plug at the 12 o’clock position and add oil until it begins to flow out of the hole at the 3 o’clock position. Adjusting the Traction-Pedal Angle 4. Install both plugs. 1. Loosen the 2 nuts and bolts securing the left side of the traction pedal to the bracket (Figure 60).
Checking the Rear-Axle-Gearbox Lubricant 6. Through the open hole, slowly fill the planetary with 0.65 L (22 oz) of high quality SAE 85W-140 wt gear lube. Service Interval: Every 400 hours Important: If the planetary fills before the 0.65 L (22 oz) of oil is added, wait 1 hour or install the plug and move the machine approximately 10 feet to distribute the oil through the brake system. Then, remove the plug and add the remaining oil. The gearbox is filled with SAE 85W-140 gear lube. The capacity is 0.
Checking the Rear Wheel Toe-In Service Interval: Every 800 hours 1. Measure the center-to-center distance (at axle height) at the front and rear of the steering tires. Note: The front measurement must be 6 mm (1/4 inch) less than the rear measurement. 2. To adjust, loosen the clamps at both ends of the tie rods. 3. Rotate the tie-rod end to move the front of the tire inward or outward. Figure 66 1. Drain-plug location 4. Tighten the tie-rod clamps when the adjustment is correct. 5.
Cooling System Maintenance Important: Do not use water only or alcohol/methanol base coolants, as this may cause damage. 4. Install the radiator cap and expansion-tank cap. Cooling System Safety Servicing the Engine-Cooling System CAUTION Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. • Do not remove the radiator cap when the engine is hot.
Brake Maintenance Adjusting the Service Brakes Adjust the service brakes when there is more than 25 mm (1 inch) of “free travel” of the brake pedal, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before you feel braking resistance. 1. Disengage the locking latch from the brake pedals so that both pedals work independently of each other. 2. To reduce free travel of the brake pedals, tighten the brakes as follows: A.
Belt Maintenance Tensioning the Blade-Drive Belts Servicing the Alternator Belt Service Interval: After the first 10 hours Every 50 hours Service Interval: After the first 10 hours When properly tensioned, the inside measurement of the extension spring (hook to hook) should be approximately 8.3 to 9.5 cm (3-1/4 to 3-3/4 inches). Once the correct spring tension is attained, adjust the stop bolt (carriage bolt) until there is approximately 2 to 5 mm (0.065 to 0.
Hydraulic System Maintenance Note: If the stop bolt is ever removed from the mounting tab, make sure that it is installed again in the hole that aligns the stop-bolt head with the idler arm. 4. Remove the bolts securing the hydraulic motor to the mower deck (Figure 74). Hydraulic System Safety WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 Material Properties: Viscosity, ASTM D445 St @ 40° C 44 to 48 St @ 100° C 7.9 to 8.
Replacing the Hydraulic Filters Important: Use only the hydraulic fluids specified. Other fluids could cause system damage. Service Interval: After the first 200 hours Every 800 hours Use Toro replacement filters Part No. 94-2621 for the rear (mower deck) of the machine and Part No. 75-1310 for the front (charge) of the machine. Important: Use of any other filter may void the warranty on some components. 1.
Mower Maintenance Adjusting the Counterbalance Pressure Pivoting (Tilting) the Center Mower Deck to the Upright Position The counterbalance test port is used to test the pressure in the counterbalance circuit (Figure 78). The recommended counterbalance pressure is 2,241 kPa (325 psi). To adjust the counterbalance pressure, loosen the locknut, rotate the adjusting screw (Figure 78) clockwise to increase the pressure, or counterclockwise to decrease the pressure and tighten the locknut.
3. Rotate a blade to point straight forward. 4. Using a short ruler, measure from the floor to the front tip of the blade. 5. Rotate the blade tip to the rear and measure from the floor to the tip of the blade. 1 6. Subtract the front dimension from the rear dimension to calculate the blade pitch. 2 Adjusting the Center Mower-Deck Pitch 1. Loosen the jam nuts on the top or bottom of the height-of-cut-chain U-bolt (Figure 81). 2.
Adjusting the Wing Mower Decks 1. Remove the cap screws and nuts securing the castor arm to the castor fork (Figure 82). 2. Position the shims, as required, to raise or lower the castor wheel until the mower deck has the correct pitch. 3. Install the capscrews and nuts. Figure 83 1. Caster-arm tube 2. Bushings 5. Apply grease to the inside and outside of the new bushings. 6. Using a hammer and flat plate, drive the bushings into the mounting tube. 7.
Figure 85 1. Caster wheel 3. Bearing 2. Caster-pivot arm 4. Bearing spacer Figure 86 2. Remove the bearing from the wheel hub and allow the bearing spacer to fall out (Figure 84 and Figure 85). 3. Remove the bearing from the opposite side of the wheel hub. 4. Check the bearings, spacer, and inside of the wheel hub for wear and replace any damaged parts. 5. To assemble the caster wheel, push the bearing into the wheel hub. Note: When installing the bearings, press on the outer face of the bearing. 6.
Blade Maintenance Removing and Installing the Mower Blade(s) Blade Safety The blade must be replaced if a solid object is hit, the blade is out of balance, or if the blade is bent. Always use genuine Toro replacement blades to ensure safety and optimum performance. DANGER A worn or damaged blade can break, and a piece of the blade could be thrown at you or bystanders, resulting in serious personal injury or death.
1. Position the machine on a level surface, raise the mower deck, engage the parking brake, put the traction pedal in NEUTRAL, put the PTO lever in the OFF position, shut off the engine, and remove the ignition key. 2. Examine the cutting ends of the blade carefully, especially where the flat and curved parts of the blade meet (Figure 89). Figure 90 Note: Because sand and abrasive material can wear away the metal that connects the flat and curved parts of the blade, check the blade before using the mower.
Cab Maintenance Important: Do not use more than 3 shims at any 1 hole location. Use decreasing numbers of shims in adjacent holes if more than 1 shim is added to any 1 hole location. Pressure Washing the Cab 8. Adjust the idler pulley and install the belt covers. Important: Use care around cab seals and lights (Figure 91). If you are using a pressure washer, keep the washer wand at least 0.6 m (2 ft) away from the machine.
Cleaning the Air-Conditioning Coil Cleaning the Cab-Air Filters Service Interval: Every 250 hours (Replace them if they are torn or excessively dirty.) Service Interval: Every 250 hours (Clean more frequently in extremely dusty or dirty conditions) 1. Remove the screws and grates from over both the in-cab and rear cab-air filters (Figure 92). 1. Shut off the engine and remove the key. 1 2 2. Remove the 6 nuts and washers from the bottom of the rear of the cab (Figure 94).
Storage 6. Replace the air-conditioning coils, air filters and cabin roof. Preparing for Seasonal Storage Traction Unit 1. Thoroughly clean the traction unit, mower decks, and the engine. 2. Check the tire pressure; refer to Checking the Tire Pressure (page 24). 3. Check all fasteners for looseness; tighten as necessary. 4. Grease or oil all grease fittings and pivot points. Wipe up any excess lubricant. 5. Lightly sand and use touch-up paint on painted areas that are scratched, chipped, or rusted.
Notes: 70
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
