Installation Instructions

ManualsBrandsToro ManualsAttachmentsPre-Filter Screen Kit, 2015 and After Groundsmaster Series Cab

FormNo.3401-429RevA

Pre-FilterScreenKit

2015andAfterGroundsmaster

SeriesCab

ModelNo.30647

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Frontscreenmount1

Carriagebolt(1/4x3/4inch)

Flangenut6

Latch-mountassembly2

Latch-mountbracket2

Assemblethekit.

Prelterscreen

Prelter-backplate

Latch2

Nut(#8)

Plasticbolt(1/4x1-1/8inches)

Bolt(#8x1/2inch)

Handle2

Assembletheltercover.

Frontscreenmount1

Self-tappingscrew(5/16x1/2inch)

Latch-mountassembly2

Latch-mountbracket2

Installthelterkit.

Nopartsrequired

–

Installthelters.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3401-429*A

Summary of content (8 pages)

PAGE 1
Form No. 3401-429 Rev A Pre-Filter Screen Kit 2015 and After Groundsmaster® Series Cab Model No. 30647 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Assembling the Filter Mounts Assembling the Latch Mount Assembling the Front Screen Mount 2015 Model Only 1. Use Figure 2 to orient the latch-mount assembly before it is installed. 2015 Model Only 1. Loosely install the 2 carriage bolts (1/4 x 3/4 inch) and flange nuts to the front-screen mount (Figure 1). Figure 1 1. Front-screen mount 2. Carriage bolts (1/4 x 3/4 inch) 3. Flange nuts (1/4 inch) 2.
PAGE 3
Assembling the Latch Mount Assembling the Filter Cover 2016 Model Only Use this procedure to install both handle assemblies. 1. Align the prefilter-back plate to the prefilter screen (Figure 4). 1. Use Figure 3 to orient the latch-mount assembly before it is installed. Figure 3 1. Latch-mount bracket 3. Latch-mount pin Figure 4 2. Latch-mount assembly 2. Push the latch-mount assembly through the opening in the bracket (Figure 3). 1. Latch 2. Nut (#8) 5. Prefilter screen 6.
PAGE 4
Installing the Filter Mounts Installing the Front Mount Locating the Install Location 2016 Model Only Locate the area on the cab where the filter screen will be installed (Figure 5). Use the 3 self-tapping screw (5/16 x 1/2 inch) to secure the front-screen mount to the plate (Figure 7). 1 Figure 7 1. Front-screen mount 2. Self-tapping screw (5/16 x 1/2 inch) Installing the Latch Mount g027786 2016 Model Only Figure 5 1.
PAGE 5
Installing the Filters 1. Insert the tabs on the filter screen into the tab slots on the front-filter mount (Figure 9). Figure 9 2015 model shown 2. Filter screen 1. Cab-filter mount 2. Install the filters into the filter screen (Figure 10). Figure 10 2015 model shown 1. Upper filter 2. Lower filter 3. Rotate the filter screen around the tabs until the latch locks into the latch-mount assembly (Figure 11). Figure 11 2015 model shown 1. Latch-mount assembly 3. Screen cover 2.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8