Installation Instructions

ManualsBrandsToro ManualsAttachmentsRear Discharge Completion Kit, Base 62in Mower for Groundsmaster 3400 Traction Unit

FormNo.3372-820RevB

RearDischargeCompletionKit

Base62inand72inMowersforGroundsmaster

3400TractionUnit

ModelNo.30648

ModelNo.30649

InstallationInstructions

Installation

The62inchRearDischargeCompletionKit,Model

30648canbeinstalledonthebasemower,Model30645

The72inchRearDischargeCompletionKit,Model

30649canbeinstalledonthebasemower,Model30646

62InchRearDischarge

CompletionKitInstallation

1.Blockupthedecksoitdoesnotaccidentallyfall.

2.Removethecoversfromthetopofthedeck.

3.Looselymountthedeckchamberstotheunder

sideofthemowerdeckwith(12)5/16x3/4inch

carriageboltsandangenuts.Theboltheadsareto

bepositionedinsidethemowerdeck.Positionthe

chambersasshownin

Figure1.

Note:Use3boltsandnutsfortheleftchamber,4

forthecenterchamberand5fortherightchamber.

Figure1

1.L.H.chamber3.R.H.chamber

2.Centerchamber

4.Looselymounttheouterchamberstothecenter

chamberwith(2)5/16x3/4inchcarriageboltsand

angenuts(Figure1).

5.MounttheL.H.footshieldtothelefthandcorner

ofthecuttingunitwith(4)5/16x3/4inchcarriage

boltsandangenutsasshownin

Figure2.

g0181 12

Figure2

1.L.H.footshield

6.MounttheR.H.footshieldtotherightrearcorner

ofthecuttingunitwith(2)5/16x3/4inchcarriage

boltsandangenuts.Inserttheboltsfromthe

inside.PositiontheshieldasshowninFigure3.

g0181 13

Figure3

1.R.H.footshield

7.The16.75inch(426mm)long,outsideap,the

outsidestrapandtheoutsideanglearepre-assembled

atthefactory(Figure4).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3372-820 Rev B Rear Discharge Completion Kit Base 62in and 72in Mowers for Groundsmaster® 3400 Traction Unit Model No. 30648 Model No. 30649 Installation Instructions Installation The 62 inch Rear Discharge Completion Kit, Model 30648 can be installed on the base mower, Model 30645 The 72 inch Rear Discharge Completion Kit, Model 30649 can be installed on the base mower, Model 30646 4.
PAGE 2
1 g0181 14 3 Figure 4 1. Outside flap 3. Outside angle 2. Outside strap 8. Mount the assembly to the left rear corner of the cutting unit with (2) 5/16 x 1–1/4 inch carriage bolts and flange nuts (Figure 4). Figure 6 9. The 12 inch (305 mm) long, outside flap, the outside strap and the outside angle are pre-assembled at the factory (Figure 5). 1. Center flap 3. Center angle 2. Center strap 12.
PAGE 3
17. Remove the blocks and lower the deck. 18. Affix an identification decal to the top of the mower deck near the serial plate (Figure 8 and Figure 9). Make sure the mounting surface is clean. COMPLETION KIT, MODEL 30648, INST ALLED 111-5615 Affix this identification decal, part no. 111–5615 onto 62 inch mower decks. GO T O WWW.TORO.COM FOR SER VICE PART INFORMATION g018043 Figure 8 1 Figure 10 1. Outside flap 4. Center chamber 2. Outside strap 5. L.H. chamber 3. RH chamber g0181 16 4.
PAGE 4
1 2 g0181 19 1 3 Figure 13 1. Outside flap 3. Outside angle 2. Outside strap g0181 17 Figure 11 11. Mount the assembly to the rear of the cutting unit with (3) 5/16 x 3/4 inch carriage bolts and flange nuts (Figure 13). 1. Support bracket 7. Tighten the fasteners. 12. The center flap, the center strap and the center angle are pre-assembled at the factory (Figure 14). 8. Loosely mount the side of the R.H.
PAGE 5
1 g018120 Figure 15 1. Blade bolt 2. Anti-scalp cup Figure 17 3. Blade 1. Identification decal Important: The curved part of the blade must be pointing toward the inside of the cutting unit to ensure proper cutting. 15. Rotate the blades to make sure there is no interference. 16. Tighten all the mounting nuts. 17. Install the covers to the top of the deck. 18. Remove the blocks and lower the deck. COMPLETION KIT, MODEL 30649, INST ALLED 111-5616 19.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8