Installation Instructions

ManualsBrandsToro ManualsRiding Products62in CE Mower Cover Kit, Groundsmaster 7200 or 7210 Traction Unit

FormNo.3391-128RevA

CEKitfor62inand72inBaseMowerDecks

Groundsmaster

7200,7210,or360TractionUnit

ModelNo.30683

ModelNo.30685

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Pulleyshield1

Pushnut1

Mountthepulleyshield.

Driveshaftcover

Lockwasher,3/8inch

Hexheadscrew,3/8x3/4inch

Mountthedriveshaftcover.

Pivotbracket1

Lockwasher,3/8inch

Hexheadscrew,3/8x3/4inch

Mountthepivotbracket.

Shieldsupport(Groundsmaster7210)

Shieldsupport(Groundsmaster360)

Hexheadscrew,5/16x4inch

Washer,.391I.D.1

Flangenut,5/16inch

Mounttheshieldsupport.

Driveshaftshield

Shoulderscrew

Flatwasher,.469I.D.1

Pushnut1

Retainernut1

Mountthedriveshaftshield.

Innerdeckcover1

Grommet

Hexangescrew,5/16x3/4inch

Pushnut1

Mounttheinnerdeckcover.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3391-128*A

Summary of content (8 pages)

PAGE 1
Form No. 3391-128 Rev A CE Kit for 62in and 72in Base Mower Decks Groundsmaster® 7200, 7210, or 360 Traction Unit Model No. 30683 Model No. 30685 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Procedure Description 1 3 1 1 1 1 2 3 2 1 Left deck cover Grommet Hex flange screw, 5/16 x 3/4 inch Push nut Right deck cover Cover support Grommet Hex flange screw, 5/16 x 3/4 inch Flange nut, 5/16 inch Push nut 8 9 Use Qty. Mount the left deck cover. Mount the right deck cover. Media and Additional Parts Description Use Qty. Installation instructions 1 Reference for installation of kit Parts catalog 1 Use to reference part numbers 1 2 1 Preparing the Mower No Parts Required Procedure 1.
PAGE 3
1 2 3 1 4 2 2 3 3 g026679 Figure 3 5 g026678 1. Drive shaft cover Figure 2 1. Nut (2) 4. Retainer nut 2. Washer (2) 5. Carriage bolt 2. Lockwasher (2) 3. Pulley shield 4 3. Install the retainer nut over the empty hole in the pivot pulley shield (Figure 2). Mounting the Pivot Bracket Note: The retainer nut will be used later in the installation of the center cover.
PAGE 4
5 Mounting the Shield Support Parts needed for this procedure: 1 Shield support (Groundsmaster 7210) 1 Shield support (Groundsmaster 360) 1 Hex head screw, 5/16 x 4 inch 1 Washer, .391 I.D. 1 Flange nut, 5/16 inch For the Groundsmaster 7210 Install the shield support to the right side of the frame with a hex head screw, washer and flange nut. Use the large hole in the front of the frame for the installation. The tab on the shield goes into the small hole in the frame (Figure 5).
PAGE 5
1 2 g026736 Figure 6 1. Bolt 2. Nut 2. Install the shield support to the right side of the frame with the nut and bolt, removed in the previous step (Figure 7). 1 2 3 g026686 Figure 7 1. Bolt 2. Shield support 5 3.
PAGE 6
7 Mounting the Drive Shaft Shield Mounting the Inner Deck Cover Parts needed for this procedure: Parts needed for this procedure: 1 Inner deck cover 1 Drive shaft shield 2 Grommet 1 Shoulder screw 1 Hex flange screw, 5/16 x 3/4 inch 1 Flat washer, .469 I.D. 1 Push nut 1 Push nut 1 Retainer nut Procedure 1. Insert a grommet into each hole in the side of the inner cover (Figure 9). Procedure 1 1. Install the retainer nut over the empty hole in the pivot bracket (Figure 8). 2 3 2.
PAGE 7
8 9 Mounting the Left Deck Cover Mounting the Right Deck Cover Parts needed for this procedure: Parts needed for this procedure: 1 Left deck cover 3 Grommet 1 Right deck cover 1 Hex flange screw, 5/16 x 3/4 inch 1 Cover support 1 Push nut 2 Grommet 3 Hex flange screw, 5/16 x 3/4 inch 2 Flange nut, 5/16 inch 1 Push nut Procedure 1. Insert a grommet into each of the 3 holes in the left deck cover (Figure 10). 1 2 Procedure 3 1 1.
PAGE 8
Declaration of Incorporation Model No. Serial No. 30683 None and Up 30685 None and Up Product Description Invoice Description CE kit for 62” base mower deck CE kit for 72” base mower deck CE KIT 62IN DECK WITH FRENCH GUARDS CE KIT 72IN DECK WITH FRENCH GUARDS General Description Directive Traction Unit 2006/42/EC Multi-Purpose Machine 2006/42/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.