Form No. 3444-746 Rev A CE Guard Kit Groundsmaster® 360 Multi-Purpose Machine Model No. 30689 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal144-7254b 144-7254 1. Read the Operator’s Manual.
decal144-7261 144-7261 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 Description Use Qty. Push nut (3/8 inch) 2 Right shield Rear shield U-bolt Flange nut Locking latch Latch plate Bolt (3/8 x 1 inch) Flange locknut (3/8 inch) Latch key Flange head bolt (3/8 x 1 inch) Push nut (3/8 inch) Retaining nut (3/8 inch) Flange head bolt (3/8 x 1 inch) Push nut (3/8 inch) Retaining nut (3/8 inch) 1 2 2 2 1 1 1 1 1 1 1 1 1 1 1 6 Push nut 2 Secure the front cover.
1 2 Securing the Storage Compartment Installing the Shield(s) Parts needed for this procedure: Parts needed for this procedure: 2 Push nut (3/8 inch) Procedure 1. Park the machine on a level surface, lower the cutting unit or attachment, engage the parking brake, and shut off the engine, and remove the key. 2. Unlatch and raise the hood. Use the prop rod to hold it in place. 3. Remove the 2 flange head bolts securing the storage compartment support bracket to the frame (Figure 1).
For Models Equipped With a Yanmar Engine (Without a Cab) 1. Loosely install a rear shield to the right rear frame tube with a U-bolt and 2 flange nuts (Figure 3). 2. Position the shield near the tube radius and contacting the frame plate. g026721 Figure 4 1. Flange nuts 3. U-bolt 2. Rear shield 3. 3 g026720 Figure 3 1. Flange nuts Tighten the flange nuts. 3. U-bolt 3. Tighten the flange nuts. Installing the Hood Locking Latch 4. Repeat steps 1 through 3 at the left side of the machine.
4 Securing the Floor Plate Parts needed for this procedure: 1 Flange head bolt (3/8 x 1 inch) 1 Push nut (3/8 inch) 1 Retaining nut (3/8 inch) Procedure 1. Raise the floor plate. 2. Install a retaining nut at the frame hole under the right front corner of the floor plate (Figure 6). g014581 Figure 5 1. Plug 4. Flange nut 2. Latch 5. Latch plate 3. Latch key 6. Carriage screw 4. Install the locking latch through the square hole in the right side of the hood.
5 6 Securing the Seat Plate Securing the Front Cover Parts needed for this procedure: Parts needed for this procedure: 1 Flange head bolt (3/8 x 1 inch) 1 Push nut (3/8 inch) 1 Retaining nut (3/8 inch) 2 Push nut Procedure 1. Procedure 1. Raise the seat plate. 2. Install a retaining nut at the frame hole under the left rear corner of the seat plate (Figure 7). Remove the 2 flange head bolts securing the front cover to the top of the front axle (Figure 8). g014584 Figure 8 1.
7 8 Securing the Belt Covers Securing the Floor Plate Parts needed for this procedure: Cab Models Only 2 Flange head bolt (5/16 x 1-1/4 inches) 2 Retaining nut (5/16 inch) 2 Push nut Parts needed for this procedure: 4 Push nut Procedure Procedure 1. Perform this procedure for the right and left side belt covers. 1. Remove the hand knobs securing the belt covers to the mower deck (Figure 9). Remove the belt covers. 2. Install a retaining nut at the forward hole in the deck bracket.
Securing the Firewall Cab Models Only Parts needed for this procedure: 4 Push nut Procedure 1. Remove the 4 bolts securing the firewall to the frame (Figure 11). g014587 Figure 11 1. Firewall 2. Flange head bolt 3. Push nut 2. Install the flange head bolts into the firewall using push nuts (3/8 inch). 3. Secure the firewall to the frame with the flange head bolts.
Installing the Decal Parts needed for this procedure: 1 Stability decal (Part No. 144-7261) 1 Sound decal (Part No.
g351697 Figure 12 1. Tipping hazard portion—stability decal (Part No. 138-8203) 3. Dampen the area with water or mildly soapy water. 4. Peel off the backing of the decal portion, apply it over the existing tipping-hazard warning as shown in Figure 12, and squeegee across the decal using overlapping strokes from the center toward the edges.
Pre-2015 Model-Number Configuration Table (cont'd.) 31223 4WD Kubota 1505 A B C D* Highlighted values (*) that show the standard configuration of the model. These numbers include an uncertainty value (k) of 1 dBA. Sound power level was determined according to procedures outlined in ISO 11094. 1. Use the Sound-Power Decal Portion Table and the 2 model-number configuration tables to select the portion of the sound decal (144-7253) for your machine. 2.
