Form No. 3327–122 Groundsmaster 345 Traction Unit Model No. 30789—Serial No.
FOREWORD The GROUNDSMASTER 345 was developed to satisfy the demand for a maneuverable, intermediate size, turf maintenance rotary mower. The machine has advanced concepts in engineering and design, and if maintained properly, it will give excellent service. Since the GROUNDSMASTER 345 is a high–quality product, Toro is concerned about the future use of the machine and safety of the user. Therefore, read this manual to familiarize yourself with proper set–up operation and maintenance instructions.
TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . 4-6 ENGINE MAINTENANCE . . . . . . . . . . . . . . . . . . 26-29 SAFETY AND INSTRUCTION DECALS . . . . . . . 6-7 Cleaning Radiator and Screen . . . . . . . . . . . . . . . 26 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Changing Crankcase Oil and Filter . . . . . . . . . . . 26 LOOSE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Replacing Fuel Filter . . . . . . . . . . . . .
SAFETY INSTRUCTIONS The GROUNDSMASTER 345 was tested and certified by TORO for compliance with the B71.4—1999 specifications of the American National Standards Institute. Although hazard control and accident prevention partially are dependent upon the design and configuration of the machine, these factors are also dependent upon the awareness, concern, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the machine.
SAFETY INSTRUCTIONS 14. Using the machine demands the operator’s complete attention. To prevent loss of control: A. Operate only in daylight or when there is good artificial light. B. Drive slowly. C. Avoid sudden stops and starts. D. Look behind machine before backing up. E. Watch for holes or other hidden hazards. F. Do not drive close to a sand trap, ditch, creek, or hazard. G. Reduce speed when making sharp turns and when turning on a hillside. H.
SAFETY INSTRUCTIONS 33. Before disconnecting or performing any work on the hydraulic system, all pressure in system must be relieved by stopping engine and lowering implement to the ground. 34. If the engine must be running to perform maintenance or an adjustment, keep clear of PTO shaft, cutting unit blades, and other moving parts. 35. Do not overspeed the engine by changing the governor settings. Maximum engine speed with no load is 3300 rpm.
SAFETY AND INSTRUCTION DECALS UNDER HOOD ABOVE RADIATOR CAP (Part No. 82–8970) ON CONTROL PANEL (Part No. 105–0080) ON FRAME NEAR FRONT WHEELS (Part No. 67–1720) NEAR FUEL TANK CAP (Part No. 27–7310) NEAR TOOL BOX COVER (Part No. 67–1710) GAS UNLEADED FRONT BULKHEAD (Part No. 53–4430) NEAR FUEL TANK (Part No. 53–4420) ON BATTERY COVER (Part No. 92–7802) NEAR LIFT LEVER (Part No.
SPECIFICATIONS Engine: Ford, 4 cycle, 4-cylinder, overhead valve, liquid cooled gas engine with centrifugal water pump. Ford rates engine @ 52 hp (De–rated to 25.5 hp). Mechanically governed to a maximum speed of 3200 ± 100 rpm. 79 cu. in. (1300 cc) displacement. Distributor less electronic ignition. 3.5 quart (3.25 liter) oil capacity; replaceable oil filter. Forged connecting rods, cast iron cylinder head and block. Mechanical fuel pump. Spark arrestor muffler is standard.
SPECIFICATIONS OPTIONAL EQUIPMENT: Tire Chains (Front), Part No. 11-0390 (set of 2) Cutting Unit, Model No. 30722 (L.H. Side Discharge) Wheel Weight Kit, Part No. 11-0440 (set of 2) Cutting Unit, Model No. 30710 (Rear Discharge) Rear Weight Kit, Part No. 24-5780 (set of 2) Cutting Unit, Model No. 30716 (Guardian 72” Recycler) Rear Weight Kit, Part No. 24-5790 (Qty. 1) Cutting Unit, Model No. 30799 (Flex 72” ) Cushion Seat, Model No. 30623 4–Ply Wide Tire w/ Rim, 23 x 10.5 x 12 , Part No.
LOOSE PARTS Note: Use this chart as a checklist to ensure all parts necessary for assembly have been shipped. If any of these parts are missing, total set–up cannot be completed. DESCRIPTION QTY. USE Steering Wheel Foam Seal Nut Screw Cap 1 1 1 1 1 Manual Tube (shipped in tool box) R–Clamp 1 2 Install on right underside of seat Ball Joint R.H. (Shipped in tool box) 1 Install Ball Joint (implement installation) and Connect Lift Cylinder.
SET–UP INSTRUCTIONS 2. Mount seat pivot bracket to frame with (2) flange screws supplied in kit (Fig. 4). REMOVE BATTERY FROM CHASSIS 1. Release the two latches holding instrument cover in place. Carefully remove instrument cover to expose the battery. 2. Remove two wing nuts and hold down strap that secures battery (Fig. 2). Lift battery out of chassis. Keep wing nuts and hold down strap in safe place for later use. 3. Activate and charge battery, refer to Activate and Charge Battery. 1 Figure 4 1.
SET–UP INSTRUCTIONS 3. Mount seat support over four threaded studs at the bottom of seat suspension assembly and secure in place with lockwashers and nuts (Fig. 7). Note: When mounting seat suspension, use forward set of mounting holes for a shorter operator, as shown in figure 7, or rear set for a taller operator. 4. Mount seat pivot bracket to frame with (2) flange screws supplied in kit (Fig. 4) 5. Mount seat and seat support to seat pivot bracket with pivot shaft and roll pin (Fig. 5).
SET–UP INSTRUCTIONS 1 4. Have a helper push down on the left push arm. Then insert a 2 x 4 in. (51 x 102 mm) block of wood between the frame and top of the push arm (Fig. 10). Screw ball joint into left hand push arm until center of ball joint is 2-3/8 inches (60 mm) away from front of push arm (Fig.11). Do not tighten jam nut. 1 Figure 9 1.
SET–UP INSTRUCTIONS CHECK TORQUE OF FRONT WHEEL NUTS WARNING Tighten front wheel nuts to 45-55 ft–lb (61-75 N m) after 1-4 hours of operation and again after 10 hours of operation and every 250 hours thereafter. Failure to maintain proper torque could result in failure or loss of wheel and may result in personal injury. GREASE TRACTION UNIT Before the machine is operated, it must be greased to assure proper operating characteristics; refer to Lubrication Maintenance.
BEFORE OPERATING 3. Remove dipstick and wipe it with a clean rag (Fig. 13). Push dipstick down into the tube and ensure it is fully seated. Pull dipstick out of the tube and check level of oil. If oil level is low, remove filler cap (Fig. 13) and add enough oil to raise level to top notch on dipstick. DO NOT OVERFILL. 2 1 BUILD–UP OF COMBUSTION CHAMBER DEPOSITS. LEADED GASOLINE CAN BE USED IF UNLEADED IS NOT AVAILABLE.
BEFORE OPERATING CHECK COOLING SYSTEM Clean debris off screen and front of radiator daily, hourly if conditions are extremely dusty and dirty; refer to Cleaning Radiator and Screen. The cooling system is filled with a 50/50 solution of water and permanent ethylene glycol anti–freeze. Check level of coolant at beginning of each day before starting the engine. Capacity of cooling system is approximately 6 quarts (5.7 L). 1. Carefully remove radiator cap.
CONTROLS Traction Pedal (Fig.16)—Traction pedal has two functions; one is to make the machine move forward, the other is to make it move backward. Using the heel and toe of the right foot, depress top of pedal to move forward and bottom of pedal to move backward. Ground speed is proportionate to how far pedal is depressed. For maximum ground speed with no load, traction pedal must be fully depressed while throttle is in FAST position. Maximum speed forward is approximately 9.5 mph (15 km/hr).
CONTROLS 5 3 2 4 IMPORTANT: If the switch must be overridden because of an emergency, the engine can be started and will continue to run while reset switch is held in. 7 6 8 1 11 Ignition Switch (Fig. 18) – The key switch, which is used to start and stop the engine, has three position: OFF, RUN, and START. Rotate key clockwise to the START position to engage starter motor. When engine starts, release key and it will move automatically to the ON position.
OPERATING INSTRUCTIONS STARTING/STOPPING ENGINE 1. Ensure parking brake is set, PTO lever is in OFF position (Fig. 18), and lift lever is in TRANSPORT or FLOAT position (Fig. 17). Remove foot from traction pedal and insure it is in neutral. 2. Move throttle control (Fig. 18) to1/4–1/3 open position. 3. To start engine, move choke lever (Fig. 18) fully forward. 4. Insert key into ignition switch (Fig. 18) and rotate it clockwise to START position.
OPERATING INSTRUCTIONS 1. Reach under traction unit and rotate by–pass valve (Fig. 20) 1/2 to 1 turn counterclockwise. Opening the valve opens an internal passage in the transmission, thereby by–passing transmission oil. Because fluid is by–passed, traction unit can be moved without damaging the transmission. 1 Figure 20 1. By–pass valve 2. Before starting engine, close by–pass valve by rotating it clockwise until it is securely seated. Do not exceed 5 to 8 ft–lb (7-11 N m).
DAILY MAINTENANCE CHECKLIST Daily Maintenance: (duplicate this page for routine use) Daily Maintenance Check For Week Of ___________ Maintenance Check Item MON Safety Interlock Operation Grass Deflector in Down Position Brake Operation Fuel Level Engine Oil Level Cooling System Fluid Level Dust Cup and Baffle (Air Filter) Radiator & Screen for Debris Unusual Engine Noises Unusual Operating Noises Transmission Oil Level Hydraulic Hoses for Damage Fluid
LUBRICATION MAINTENANCE GREASING BEARINGS, BUSHINGS AND BRAKE CABLES The traction unit must be lubricated regularly. If machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation. 1. The traction unit bearings and bushings that must be lubricated are: PTO shaft and yokes (Fig. 21); lift arm pivots (Fig. 22); right and left push arm ball joints (Fig. 21); push arm pivot bushings (Fig. 23); PTO pivot housing blocks (Fig. 24); brake pivot bushings (Fig.
ELECTRICAL MAINTENANCE REPLACING PTO SWITCH 1. Remove instrument cover and disconnect negative battery cable from battery. 1 2. Move PTO lever forward to ON position. 2 3. Remove boot from button end of PTO switch (Fig. 28). Retain boot for reinstallation. Separate switch wire connectors. 3 Figure 29 1. Parking brake interlock switch 2. Parking brake shaft pivot paddle 3. Wire harness connector 1 3. To adjust gap, loosen switch mounting screws, adjust gap and tighten screws. Figure 28 1.
24 GY R (–) FL3 FL2 FL1 R PK W R L GN = GREEN GY = GRAY T = TAN KEY TO WIRE COLORS BK = BLACK BR = BROWN BU = BLUE B ENGINE GROUND B 7.
AIR CLEANER MAINTENANCE GENERAL MAINTENANCE PRACTICES 2. Dump dust out of the dust cup. After cleaning cup and baffle, assemble and reinstall both parts. Inspect air cleaner and hose periodically to maintain maximum engine protection and to ensure maximum service life. SERVICING AIR CLEANER FILTER 1. Assure hose between air cleaner and carburetor is clamped securely in place. Replace the hose if it is cracked or punctured.
AIR CLEANER MAINTENANCE C. Dry filter element using warm, flowing air (160 F (71 C) max), or allow element to air–dry. Do not use compressed air or a light bulb to dry the filter element because damage could result. 4. Wipe inside of air cleaner body with a damp cloth to remove excess dust. Slide filter into air cleaner body and secure it in place with wing nut and gasket. 5. Reinstall dust cup and baffle. Move thumb screw behind air cleaner body and tighten it securely.
ENGINE MAINTENANCE 1. To adjust belt tension, loosen upper and lower nuts securing idler arm to front engine mount (Fig. 35). SERVICING ENGINE BELTS Check tension of all belts initially after the first day of operation and every 100 hours thereafter. Alternator Belt 2. Pull out on idler arm until desired belt tension is achieved. 3. Tighten mounting nuts to secure adjustment. A new alternator belt (Fig. 34) is to be tensioned to 65 lbs. A used belt is to be tensioned to 40 lbs.
ENGINE MAINTENANCE IMPORTANT: Do not over speed the engine because the transmission could be damaged. ADJUSTING GOVERNOR 1. With engine shut off, move throttle control to FAST position and open hood. Check between the throttle arm and the stop on the carburetor base to make sure there is 1/32” (0.8 mm) gap (Fig. 36). If gap is not correct, adjust throttle rod (Fig. 36) by turning ball joint ends until gap is 1/32” (0.8 mm). If gap is correct, proceed to step 2.
ENGINE MAINTENANCE Note: If the throttle control on the instrument panel will not stay in the FAST position during operation, remove the panel cover and tighten the nut and capscrew at base of throttle lever assembly. 1 2 CHECKING OIL LEVEL IN GOVERNOR 3 The governor is shipped with oil in it, but the level of oil must be checked after every 250 hours of operation. 1. Position machine on level surface and shut engine off. 2. Disengage hood latch and open the hood. Figure 38 3.
TRACTION DRIVE MAINTENANCE ADJUSTING TRACTION CONTROL ROD 1. Check traction drive neutral position to assure front wheels do not creep; refer to Adjusting Traction Drive for Neutral. 2. Press down on front of traction pedal and check travel. There should be approximately 3.50” clearance between end of pedal and floor plate when pedal in fully depressed (Fig. 39). Adjust pump control rod (Fig. 40) to attain dimension. ADJUSTING TRACTION PEDAL FRICTION WHEEL 1.
TRACTION DRIVE MAINTENANCE 7. Should front wheel continue to rotate, check for the following: A. Ball bearing is loose or worn out (Fig. 41). B. Plunger on interlock switch is sticking. 9. Adjust traction control rod; refer to Adjusting Traction Control Rod. ADJUSTING TRACTION INTERLOCK SWITCH C. Loose or missing fasteners. 1. Adjust transmission for neutral; refer to Adjusting Traction Drive for Neutral. D. Worn roll pin securing pump lever to transmission. 2. Actuate the pump lever (Fig.
STEERING MAINTENANCE ADJUSTING TILT STEERING CONTROL If steering wheel tilt control lever must be adjusted, proceed as follows: 1. Remove knob from parking brake and self tapping screws from steering column cover. Slide cover up steering shaft to expose pivot bracket (Fig. 43). 2. Loosen small nut, rotate pivot bracket until it tightens large nut below (Fig. 43). Retighten small nut. 3. Reinstall steering column cover and parking brake knob. 1 Figure 44 1. Steering plate ADJUSTING REAR WHEEL BEARINGS 1.
BRAKE MAINTENANCE ADJUSTING BRAKES Adjust the service brakes when there is more than one inch (25 mm) of “free travel” of the turn pedals, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before braking resistance is felt. The brakes should only need adjusting after considerable use. These periodic adjustments can be performed where the brake cables connect to the brake pedal mount.
HYDRAULIC SYSTEM MAINTENANCE REPLACING HYDRAULIC OIL FILTER The hydraulic oil filter keeps the hydraulic system relatively free of contaminants and must be serviced at regular intervals. Initially, change filter after first ten hours of engine operation, and thereafter, after every 200 hours of operation or yearly, whichever comes first. Use TORO oil filter, Part No. 23–9740, as a replacement. 1. Clean area where hydraulic oil filter mounts. Remove filter from base (Fig.
HYDRAULIC SYSTEM MAINTENANCE 8. Start and run the engine at idle speed for about two minutes and turn the steering wheel lock to lock to purge air trapped in the system. Shut the engine off. 9. Leave machine set for two additional minutes, then remove dipstick and check oil level in axle (Fig. 51). If level is low, add oil until level matches groove in dipstick (Fig. 51). If level is too high, remove drain plug (Fig. 50) and drain oil until oil level matches groove in dipstick. 1 2 1 Figure 50 1.
HYDRAULIC SCHEMATIC 36
PREPARATION FOR SEASONAL STORAGE Traction Unit 1. Thoroughly clean the traction unit, cutting unit and the engine, paying special attention to these areas: — radiator screen — underneath the cutting unit — under the cutting unit belt covers — counterbalance springs — P.T.O Shaft Assembly — all grease fittings and pivot points 2. Check the tire pressure. Inflate all traction unit tires to 21 psi (145 kPa). 3. Remove, sharpen, and balance the cutting unit’s blades.
MAINTENANCE SCHEDULE Minimum Recommended Maintenance Intervals Maintenance Procedure Check Battery Fluid Level Check Battery Cable Connections Lubricate All Grease Fittings Lubricate Brake Cables Maintenance Interval & Service Every 50hrs Every 100hrs Every 200hrs Every 400hrs Check Cutting Unit Gear Box Oil Level Clean Under Cutting Unit Belt Covers Check Cutting Unit Drive Belt Adjustment Check PTO Belt Tension Inspect Air Filter, Dust Cup, and Baffle Change Engine Oil and Filter Check Fan and A
IDENTIFICATION AND ORDERING MODEL AND SERIAL NUMBERS The Groundsmaster 345 has two identification numbers: a model number and a serial number. These numbers are stamped into a plate located on front bulkhead left of seat. In any correspondence concerning the unit, supply the model and serial numbers to ensure correct information and replacement parts are obtained. To order replacement parts from an authorized TORO Distributor, supply the following information: 1. Model and serial numbers. 2.
The Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your 1996 or newer Toro Commercial Product (“Product”) purchased after January 1, 1997, to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first.