Form No. 3395-750 Rev B Rear Quick-Attach System 2013 and After Groundsmaster® 7200 Series Mower Model No. 30810—Serial No. 315000001 and Up Model No. 30812—Serial No. 315000001 and Up Installation Instructions Note: The machine must be equipped with the Auxiliary Power Unit Kit, Toro part no. 30382. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Procedure 4 5 6 7 8 Description Qty. Use Tee fitting (Model 30812 only) Hose clamp (3/8 inch) Cable tie Relay bracket Relay Bolt (1/4 x 1/2 inch) Nut (1/4 inch) Bolt (1/4 x 3/4 inch) Decal (from Auxiliary Power Unit Kit) Switch Relay bracket Relay Bolt (1/4 x 1/2 inch) Nut (1/4 inch) Bolt (3/8 x 2 inches) Washer (0.
2 Installing the Lift-Arm Assembly Model 30810 Parts needed for this procedure: 1 Cylinder-support assembly 2 Bolt (3/8 x 2-3/4 inches) 3 Bolt (3/8 x 1-1/4 inches) 1 Bolt (3/8 x 1 inch) 3 Nut (3/8 inch) 1 Lift-arm assembly 2 Bolt (7/8 x 4-1/2 inches) 2 Jam nut (7/8 inch) 8 Spindle washer 1 Bolt (1/2 x 1-1/2 inches) 1 Locknut (1/2 inch) 1 Cylinder-mount pivot pin 1 Grease fitting Figure 1 1. Bolt 2. Nut 2.
3. Mount the lift-arm assembly to the rear frame members, with 2 bolts (7/8 x 4-1/2 inch), 2 jam nuts (7/8 inch), and as many spindle washers as necessary to evenly shim between the right and left sides of the lift arm and rear frame members. 6. Secure the threaded link rod end to the cylinder-support assembly with a bolt (1/2 x 1-1/2 inch) and locknut (1/2 inch) as shown in Figure 5. Note: Position the components as shown in Figure 3. Figure 5 1. Lift adapter 2. Cylinder-support assembly Figure 3 1.
3 Installing the Lift-Arm Assembly Model 30812 Parts needed for this procedure: 1 Link mount 3 Bolt (3/8 x 1 inch) 3 Nut (3/8 inch) 1 Lift-arm assembly 2 Bolt (7/8 x 4-1/2 inches) 2 Jam nut (7/8 inch) 8 Spindle washer 1 Bolt (1/2 x 1-1/2 inches) 1 Locknut (1/2 inch) 1 Pivot pin 1 Grease fitting Figure 7 1. Link mount 2.
4. Adjust the length of the threaded link to 19 cm (7-1/2 inches) and tighten the jam nuts (Figure 9). 7. Thread a grease fitting into the end of the pivot pin (Figure 11). Note: Position the grease fitting as shown in Figure 12. Figure 9 1. Length of threaded link—19 cm (7-1/2 inch) Figure 12 1. Pivot pin 5. Secure the rod end of the threaded link to the link-support assembly with a bolt (1/2 x 1-1/2 inch) and locknut (1/2 inch) as shown in Figure 10. 2. Grease fitting Figure 10 1. Threaded link 2.
A. Remove the cap from the hardline of the oil-cooler return hose (Figure 15). 4 Installing the Hydraulic Hoses Parts needed for this procedure: 1 Tee fitting (Model 30812 only) 3 Hose clamp (3/8 inch) 4 Cable tie Procedure 1. On the right side of the machine, just ahead of the radiator frame, place a drain pan under the oil-cooler-return hose (Figure 13 or Figure 14). Figure 15 1. Short hose 2. Hardline cap 3. Oil-cooler-return hose B. Thread the short hose to the hardline (Figure 15). C.
5. On the right frame, locate the deck-lift-valve assembly (Figure 18). Figure 18 1. Plug 2. Valve assembly 6. Remove the plug from the left side of the valve assembly (Figure 18). 7. Thread the hydraulic valve fitting into the opening of the valve (Figure 19). Figure 17 1. Cut the hose here. 2. Tee fitting 3. To the deck-lift valve 4. From the oil cooler C. Secure all 3 hoses to the tee fitting with hose clamps (7/8 inch). D. Install the short hose to the port in the oil-cooler-return hose.
8. Route the long hose under the radiator frame, over the frame cross member, and along the frame rail to the valve (Figure 20). 5 Note: The long hose will follow another hose from the transmission bay to the valve assembly. Installing the Relays and Switches Model 30810 Parts needed for this procedure: Figure 20 1. Cable tie 2. Long hose 3. Valve 9. Secure the long hose with 4 cable ties (Figure 20).
4. Unlatch the control-panel cover and move it aside (Figure 22). Figure 24 1. Decal 3. Lift/lower switch (3-position switch) 2. Float/power-down switch (2-position switch) Figure 22 1. Control panel 9. Insert the switches into the appropriate mounting holes (Figure 24). 2. Latch Note: Position the flat portion of the switch toward the operator. 5. Locate and remove the 2 knockout plugs from the top of the control panel (Figure 23). Figure 23 1. Knockout plugs 2. Knockout plug locations 6.
3. Remove the bracket, and drill a hole (0.281 inch) through both walls of the frame in the location that you marked. 6 Installing the Relays and Switches 4. Install the bracket with the hardware you used to loosely install the bracket and secure the bracket to the new hole with a bolt (1/4 x 2-1/2 inches) and nut (1/4 inch). Model 30812 5. Install the 6 relays to the bracket using 6 bolts (1/4 x 1/2 inch) and 6 locknuts (1/4 inch).
7. Locate and remove the 2 knockout plugs from the top of the control panel (Figure 28). 7 Installing the Wiring Harness Parts needed for this procedure: 1 Wiring harness Procedure Note: The machine must be equipped with the Auxiliary Power Unit Kit, Toro part no. 30382. 1. Cover exposed connectors on the wiring harness with masking tape or electrical tape to keep debris out of the connectors while routing the harness. Figure 28 1. Knockout plugs 2.
Figure 30 Figure 31 1. Blower PTO switch (used with blower) 6. Deck lift out (A and B) 2. Lift/lower switch 7. Main wiring harness 3. Ground 8. Relays (6) 4. Power 9. Hydraulic manifold 5. Deck lift in (A and B) 10.
8 Completing Installation No Parts Required Procedure Figure 33 Model 30812 1. Grease all the new grease fittings with Number 2 lithium-based grease. 1. FLOAT /POWER-DOWN switch 2. Check the hydraulic fluid level and replenish as required. 3. Connect the negative (–) battery cable. 2. LIFT/LOWER switch Adjusting the Attachment Angle 4. Start the machine and operate the rear lift. Check for leaks and replenish hydraulic fluid as necessary.
Weight Charts for Model 30810 Use the following weight charts to determine the correct amount of front weight required for your machine. 72 inch width of cut Models 30695 with 30354, 30481, or 30353 and Additional Front Weight Required Weight Part Number Weight Description Qty.
Debris Blower (Model 30393) 253 lb 125-2655-03, 125-2670, and 114-4096 Front frame weights, Weight bracket, and Suitcase weights 4 1 3 Not Approved Rahn Groomer (Allied Product) 60 or 62 inch width of cut Models 30695 with 30456 or 30457 and Additional Front Weight Required Weight Part Number Weight Description Qty.
Debris Blower (Model 30393) 318 lb 125-2655-03, 125-2670, and 114-4096 Front frame weights, Weight bracket, and Suitcase weights 4 1 5 Not Approved Rahn Groomer (Allied Product) Weight Charts for Model 30812 Use the following weight charts to determine the correct amount of front weight required for your machine. 72 inch width of cut Models 30495, or 30487 with 30354, 30481, or 30353 With no hard canopy, model 30349 and Additional Front Weight Required Weight Part Number Weight Description Qty.
62 inch width of cut Models 30495, or 30487 with 30456 or 30457 With no hard canopy, model 30349 and Additional Front Weight Required Weight Part Number Weight Description Qty.
Operating Tips • Read and understand the attachment Operator's Manual before using the machine. • Make sure that the appropriate weight mount bracket and front weight(s) are installed for the rear attachment. • Remove rear attachment and any loose front-end weights prior to mowing. • Use care when operating the machine when a rear attachment is installed, because it is wider than the machine and may contact poles, fences, or trees. • Never operate the machine near bystanders.
Notes: 20
Notes: 21
Notes: 22
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
