Installation Instructions

ManualsBrandsToro ManualsAttachmentsFlow Divider Kit, 2008 and Before Groundsmaster 4500-D/4700-D

 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (EN)

Flow Divider Kit

Groundsmaster 4500-D/4700-D

Model No. 30830

Form No. 3351–849 Rev B

Installation Instructions

Loose Parts

Note: Use the chart below to identify parts used for assembly.

Description Qty. Use

Flow divider manifold

Large 90° fitting

Medium 90° fitting

Small 90° fitting

Large straight fitting

Small straight fitting

Bracket

Bolt (3/8 x 3-3/4 inch)

Flange nut (3/8 inch)

Hydraulic tube A

Hydraulic tube B

Hydraulic tube C

Hollow plug

Hydraulic hose D

Hydraulic tube E

Hydraulic tube F

Hydraulic tube G

Hydraulic tube H

Installing the hydraulic components

Switch

Decal

Wiring harness

T-tap assembly

Installing the wiring harness

Declaration of conformity 1

Installation instructions 1 Read before installing.

Summary of content (8 pages)

PAGE 1
Form No. 3351–849 Rev B Flow Divider Kit Groundsmaster 4500-D/4700-D Model No. 30830 Installation Instructions Loose Parts Note: Use the chart below to identify parts used for assembly. Description Qty.
PAGE 2
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-2042 1. Flow divider 2. Locked 3. Unlocked Installing the Hydraulic Components • Thread the medium 90° fitting into the left side of the flow divider manifold. Position the fitting as shown with the back-up nut fully retracted. Do not tighten at this time. 1.
PAGE 3
1 2 3 12 4 5 6 11 7 10 8 9 7 m–7595 Figure 2 Existing hydraulic configuration 1. Filter manifold assembly 2. Hydraulic tube (filter assembly to 4WD manifold) 3. Filter assembly 4. Hydraulic tube (4 WD manifold to right wheel motor) 5. Hydraulic tube (right wheel motor to filter manifold assembly) 6. Right wheel motor 7. Hydraulic tube (left to right wheel motor) 8. Test port 9. 4WD manifold assembly 4. Disconnect the hydraulic tube connecting the front of the left and right wheel motors (Ref.
PAGE 4
• Install the flow divider assembly and bracket as shown in Figure 6. 7. Replace the existing hydraulic tube running from the top of the front, right wheel motor to the manifold filter assembly with new hydraulic tube B (Fig. 4). 3 3 2 2 1 4 1 m–7597 m–7599 Figure 4 1. Hydraulic tube B 2. Front, right wheel motor Figure 6 3. Filter manifold assembly 1. Flow divider manifold assembly 2. 4WD manifold 8.
PAGE 5
14. Route hydraulic hose D to the flow divider and connect it to the 90° fitting in the bottom of the manifold (Fig. 8). 19. Install new hydraulic tube F to the straight fitting on the right side of the flow divider manifold (Fig. 9). Connect the other end to the fitting in the midsection of hydraulic tube C installed in step 8. 2 20. Install new hydraulic tube G to the 90° fitting on the front side of the flow divider manifold (Fig. 9, 10).
PAGE 6
• On machines with serial numbers prior to 249999999, use the dimensions shown in Figure 11, to locate, mark and cut a hole the size of the switch in the top of the control console. The switch should align with the edge of the deck levers. 9. Plug the female connector on the provided harness to the open power point connector on the machine. 10. Route the remainder of the harness to the flow divider manifold and secure in place with tie straps. 11.
PAGE 7
Electrical Schematic GN 2 W BK 5 2 WD / 4 WD 1 2 PK PTO SWITCH 1 3 3 4 5 OR BU 4 6 6 T 7 PK 5 2 6 4 3 1 FLOW DIVIDER W BK FLOW DIVIDER W BK POWER POINT
PAGE 8
Hydraulic Schematic 8