Installation Instructions

ManualsBrandsToro ManualsAttachmentsCrosscut Position Kit, Groundsmaster 4500-D

FormNo.3329-829RevB

CrosscutPositionKit

ForGroundsmaster4500-D

ModelNo.30832

InstallationInstructions

Installation

1.Positionthemachineonalevelsurface,lowerthe

cuttingdeckstotheoor,shuttheengineoffand

engagetheparkingbrake.

2.Removethe(4)5/16inchx5/8inchangebolts

securingtheoorplatetotheframe(Figure1).

Removetheoorplate.

Figure1

1.Floorplate

3.UsingthedimensionsshowninFigure2,locate,

markanddrilla13/16inchdiameterholethrough

theoorplateandfoottread.

Figure2

1.4–1/2inches3.13/16inchdiameterhole

2.15–7/8inches

4.Removethefrontcenterdeckfromthetractionunit

asfollows:

A.Disconnectandremovethehydraulicmotor

fromthedeck.Coverthetopofthedeckspindle

toprotectitfromcontamination.

B.Removethelynchpinsecuringthedeckcarrier

frametotheliftarmpivotpin.

C.Rollthecuttingdeckawayfromthetractionunit.

5.UsingthedimensionsshowninFigure3,locate,

markanddrill(2)7/32inchdiameterholesinthe

topofthefrontframetube.

Figure3

1.4–53/64inches3.1–3/8inches

2.7/16inch4.7/32inchdiameter

6.Mountthespringbrackettothetopoftheframe

tubewith(2)¼inchselftappingangebolts

(Figure4).

Figure4

1.Springbracket2.Selftappingbolt

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3329-829 Rev B Crosscut Position Kit For Groundsmaster 4500-D Model No. 30832 Installation Instructions Installation 1. Position the machine on a level surface, lower the cutting decks to the floor, shut the engine off and engage the parking brake. 2. Remove the (4) 5/16 inch x 5/8 inch flange bolts securing the floor plate to the frame (Figure 1). Remove the floor plate. 4. Remove the front center deck from the traction unit as follows: A.
PAGE 2
7. Reposition the fittings on the #4 and #5 cutting deck lift cylinders so the hoses are routed toward the middle of the machine (Figure 5). Cable tie the hoses together to prevent any interference (2 ties each). Figure 5 1. Cutting deck lift cylinder fittings and hoses (#5 cylinder shown) 8. Remove the flange head screws and nuts securing the #4 and #5 lift cylinder pins to the frame (Figure 6). Figure 7 1. Cylinder stop bracket 2. New cylinder pin 3. Flange nut 11.
PAGE 3
14. Position the longer end of the turnaround shaft between the cylinder stop brackets until the shaft bracket holes align with the cylinder stop bracket hole (Figure 8). Make sure the spring rests on the spring bracket. 17. Place the floor plate w/bushing over the turnaround shaft and into mounting position (Figure 10). Secure the floor plate to the frame with the (4) flange bolts previously removed. 18. Insert the pedal mounting pin into the end of turnaround shaft (Figure 10).
PAGE 4
22. While compressing the spring, insert the hair pin cotter into the second hole from the bottom of the shaft (Figure 12). To change the spring tension, move the hair pin cotter to another position on the shaft. Figure 12 1. Hair pin cotter Operation Transport Position To lift the front 2 front outboard cutting units (#4 & #5) to the fully raised position (transport), you must step on the pedal every time you pull back on the center lift lever (Figure 13 A).