Form No. 3389-419 Rev B Groundsmaster® 4300-D Traction Unit Model No. 30864—Serial No. 315000001 and Up Model No. 30864A—Serial No. 315000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. The model and serial numbers are on a plate mounted on the left side of the frame under the foot rest. Write the numbers in the space provided.
Contents Checking the Fuel Lines and Connections.................................................. 47 Servicing the Water Separator ......................... 47 Servicing the Engine Fuel Filter ........................ 47 Using the Fuel Pick-up Tube Screen ................. 48 Electrical System Maintenance ........................... 48 Servicing the Battery......................................... 48 Checking the Fuses .......................................... 49 Drive System Maintenance ................
Preparation Safety • While mowing, always wear substantial, slip-resistant footwear, long trousers, hard hat, safety glasses, and ear protection. Long hair, loose clothing, or jewelry may get tangled in moving parts. Do not operate the equipment when barefoot or wearing open sandals. Improper use or maintenance by the operator or owner can result in injury.
Operation • Do not operate the engine in a confined space • • • • • • • • • • • • where dangerous carbon monoxide and exhaust gases can collect. Mow only in daylight or in good artificial light. Before attempting to start the engine, disengage all blade attachment clutches, shift into neutral, and engage the parking brake. Remember there is no such thing as a safe slope. Travel on grass slopes requires particular care.
• Before starting the engine, sit on the seat. • Using the machine demands attention. To prevent • Carefully release pressure from components with • • • stored energy. Disconnect battery before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last. Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running. Charge batteries in an open well ventilated area, away from spark and flames.
• To ensure safety and accuracy, have an Authorized Toro Distributor check the maximum engine speed with a tachometer. • If major repairs are ever needed or if assistance is desired, contact an Authorized Toro Distributor. • Use only Toro-approved attachments and replacement parts. The warranty may be voided if used with unapproved attachments. Sound Power Level This unit has a guaranteed sound power level of 105 dBA, which includes an Uncertainty Value (K) of 1 dBA.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal93-7272 93-7272 decal117-2718 117–2718 1. Cutting/dismemberment hazard; fan—stay away from moving parts. r:\decal110-8869 110-8869 1. Warning—read the Operator's Manual, do not operate this machine unless you are trained. 2. Thrown object hazard—keep bystanders a safe distance from the machine. 3.
decal93-6681 93-6681 1. Cutting/dismemberment—hazard, fan-stay away from moving parts. decal120-4158 120–4158 1. Read the Operator’s Manual. 2. Engine—start 3. Engine—preheat 4. Engine—stop decal106-6754 106-6754 1. Warning—do not touch the hot surface. decal93-6689 93-6689 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 1. Warning—do not carry passengers. decal110-0986 110-0986 1.
decal125-2927 125–2927 1. Read the Operator’s Manual for maintenance information. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 5. Read the Operator's Manual. decal117-4764 117-4764 1.
decal104-1086 104-1086 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 5 6 7 Use Qty. No parts required – Adjust the tire pressure. No parts required – Adjust the step height. No parts required – Adjust the control arm position. No parts required – Remove shipping blocks and pins No parts required – Adjust the height-of-cut. No parts required – Adjust the roller scraper (optional). No parts required – Install the mulching baffle (optional).
g003959 Figure 2 1. Step g004152 2. Step brackets Figure 3 1. Control arm 2. Raise or lower the step to the desired height and re-secure the brackets to the frame with the 2 bolts and nuts. 3. Repeat the procedure on the other step. 2. Retaining brackets 2. 3 Rotate the control arm to the desired position and tighten the 2 bolts.
5 Adjusting the Height-of-Cut g026184 No Parts Required Figure 5 Procedure 6. 7. 8. 9. Important: This cutting deck often cuts approximately 6 mm (1/4 inch) lower than a reel cutting unit with the same bench setting. It may be necessary to have these rotary cutting deck’s bench set 6 mm (1/4 inch) above that of reels cutting in the same area. Note: Adjustments of more than 3.8 cm (1-1/2 inches) may require temporary assembly to an intermediate height to prevent binding (e.g. changing from 3.
3. Product Overview Secure the grease fitting and screw to 41 N-m (30 ft-lb) in an alternating sequence. Controls 7 Seat Adjusting Knobs Installing the Mulching Baffle (Optional) The seat adjusting lever (Figure 8) allows you to adjust the seat fore and aft. The weight adjusting knob adjusts the seat for the operator's weight. The weight gauge indicates when the seat is adjusted to the weight of the operator. The height adjusting knob adjusts the seat for the operator's height.
Parking Brake To engage the parking brake, (Figure 9) push down on the brake pedal and press the top forward to latch. To release the parking brake, press the brake pedal until the parking brake latch retracts. g021208 Figure 10 1. Lower mow/raise control lever 2. Key switch 4. Enable/disable switch 3. InfoCenter 6. Headlight switch 5. Engine speed switch Key Switch The key switch (Figure 10) has three positions: Off, On/Preheat, and Start. g003955 Figure 9 1. Traction pedal 4. Brake pedal 2.
Hydraulic Filter Restriction Indicator Using the InfoCenter LCD Display The InfoCenter LCD display shows information about your machine such as the operating status, various diagnostics and other information about the machine (Figure 13) There is a splash screen and main information screen of the InfoCenter. You can switch between the splash screen and main information screen, at any time, by pressing any of the InfoCenter buttons and then selecting the appropriate directional arrow.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.
Using the Menus To access the InfoCenter menu system, press the menu access button while at the main screen. This will bring you to the main menu. Refer to the following tables for a synopsis of the options available from the menus: Indicates the inputs, qualifiers, and outputs for enabling the PTO circuit. Engine Run Indicates the inputs, qualifiers, and outputs for starting the engine. Settings Main Menu Menu Item Description Faults The Faults menu contains a list of the recent machine faults.
Protected Menus There are 2 operating configuration settings that are adjustable within the Settings Menu of the InfoCenter: auto idle time delay and counterbalance. These settings can be locked by using the Protected Menu. Note: At the time of delivery, the initial password code is programmed by your distributor. Accessing Protected Menus Note: The factory default PIN code for you machine is either 0000 or 1234.
Setting the Counterbalance Setting the Auto Idle • In the Settings Menu, scroll down to • In the Settings Menu, scroll down to Auto Idle. Counterbalance. • Press the right button to change the auto idle time • Press the right button to select counterbalance between OFF, 8S, 10S, 15S, 20S, & 30S. and change between the low, medium, and high settings. Specifications Note: Specifications and design are subject to change without notice.
Operation Note: Determine the left and right sides of the machine from the normal operating position. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Lower the cutting decks to the ground, set the parking brake and remove the key from the ignition switch before servicing or making adjustments to the machine. g021866 Figure 16 1.
Fuel Tank Capacity Fuel Table Diesel fuel specification Location Fuel tank capacity: 53 L (14 US gallons) USA Adding Fuel ASTM D975 No. 1-D S15 No. 2-D S15 EN 590 European Union ISO 8217 DMX International JIS K2204 Grade No. 2 Japan KSM-2610 Korea 1. Park the machine on a level surface. 2. Using a clean rag, clean area around fuel tank cap. 3. Remove the cap from the fuel tank (Figure 17). • Use only clean, fresh diesel fuel or biodiesel fuels.
Checking the Hydraulic-Fluid Level Service Interval: Before each use or daily maximum biodegradability and performance the hydraulic system should be thoroughly flushed of conventional fluid. The oil is available in 19 L (5 US gallons) containers or 55 gallon drums from your Mobil Distributor. The hydraulic tank of the machine is filled at the factory with approximately 37.8 L (10 US gallons) of high quality hydraulic fluid.
Stopping the Engine Check the Torque of the Wheel Nuts 1. Torque the wheel nuts to 94 to 122 N-m (70 to 90 ft-lb) after 1-4 hours of operation and again after 10 hours of operation. Torque every 250 hours thereafter. Important: Allow the engine to idle for 5 minutes before shutting it off after a full load operation. Failure to do so may lead to trouble on a turbo-charged engine. WARNING Failure to maintain proper torque of the wheel nuts could result in personal injury. 2.
Diesel Particulate Filter Regeneration Important: Minimize the amount of time that you idle the engine or operate the engine at low-engine speed to help reduce the accumulation of soot in the soot filter. The diesel particulate filter (DPF) is part of the exhaust system. The diesel-oxidation catalyst of the DPF reduces harmful gasses and the soot filter removes soot from the engine exhaust.
DPF Ash Accumulation • When enough ash accumulates, the engine • The lighter ash is discharged through the exhaust system; the heavier ash collects in the soot filter. • Ash is a residue of the regeneration process. Over • time, the diesel particulate filter accumulates ash that does not discharge with the engine exhaust. • • The computer for the engine calculates the amount of ash accumulated in the DPF.
Types of Diesel Particulate Filter Regeneration Types of diesel particulate filter regeneration that are performed while the machine is operating: Type of Regeneration Conditions for DPF regeneration DPF description of operation Passive Occurs during normal operation of the machine at high-engine speed or high-engine load The InfoCenter does not display an icon indicating passive regeneration.
Types of diesel particulate filter regeneration that require you to park the machine: (cont'd.) Type of Regeneration Conditions for DPF regeneration DPF description of operation Recovery Occurs as a result of ignoring parked regeneration requests and continuing operation, adding more soot when the DPF is already in need of a parked regeneration When the recovery-regeneration icon is displayed in the InfoCenter, a recovery regeneration is requested.
Parked Regeneration Reset Regeneration g214713 g214711 Figure 26 Assist/reset-regeneration icon Figure 27 Parked-regeneration request icon • The assist/reset-regeneration icon displays in the • The parked-regeneration requested icon displays in the InfoCenter (Figure 27). If a parked regeneration is needed, the InfoCenter displays engine warning SPN 3719, FMI 16 (Figure 28) and the engine computer derates engine power to 85%. InfoCenter (Figure 26).
6. Engage the parking brake. 7. Set the throttle to the low IDLE position. Performing a Parked Regeneration Note: For instructions on unlocking protected menus, refer to Accessing Protected Menus (page 20). 1. Access the protected menu and unlock the protected settings submenu (Figure 29); refer to Accessing Protected Menus (page 20). g212138 Figure 31 4. When the “Initiate DPF Regen. Are you sure?” message displays, press the center button (Figure 32). g028523 Figure 29 2.
g211986 g212405 Figure 33 6. Figure 35 Move the throttle control to LOW IDLE and press the center button (Figure 34). B. The “Waiting on (Figure 36). ” message displays g212372 g212406 Figure 34 7. Figure 36 The following messages display as the parked regeneration process begins: A. C. The “Initiating DPF Regen.” message displays (Figure 35). The computer determines whether the regeneration runs.
The engine is cold—wait. The engine is warm—wait. The engine hot—regeneration in progress (percent complete). 9. g213424 The parked regeneration is complete when the “Regen Complete” message displays in the InfoCenter. Press the left button to exit to the home screen (Figure 39). Figure 37 • If the regeneration process is not allowed by the engine computer, the “DPF Regen Not Allowed” message displays in the InfoCenter (Figure 38).
Using the Jacking Points • Perform a recovery-regeneration whenever there is a loss of engine power and a parked regeneration cannot effectively clean the DPF of soot. Note: Use jack stands to support the machine when required. • A recovery regeneration requires up to 4 hours • Front—rectangular pad, under the axle tube, to complete. inside each front tire (Figure 42). • You need a distributor technician to perform the recovery regeneration process; contact your Authorized Toro Distributor.
Using the Tie Downs Understanding the Diagnostic Light • Front—the hole in the rectangular pad, under the axle tube, inside each front tire (Figure 43). The machine is equipped with a diagnostic light which indicates if the machine detects a malfunction. The diagnostic light is located on the InfoCenter, above the display screen (Figure 45).
Checking the Interlock Switches The purpose of the interlock switches is to prevent the engine from cranking or starting unless the traction pedal is in the Neutral position, the Enable/Disable switch is in the Disable position, and the Lower Mow/Raise control is in the Neutral position. In addition, the engine should stop when the traction pedal is pressed with operator off of the seat or if the parking brake is left engaged. Sit on the seat and attempt to operate the desired function of the machine.
High Lift Parallel Sail Blade The blade generally performs better in the higher heights of cut - 7 to 10 cm (2 to 4 inch). Attributes: • More lift and higher discharge velocity. • Sparse or limp turf is picked up significantly at higher heights of cut. • Wet or sticky clippings are discharged more efficiently reducing congestion in the deck. • Requires more horsepower to run. • Tends to discharge further left and can tend to windrow at lower heights of cut.
Choosing Accessories Optional Equipment Configurations Angle Sail Blade High Lift Parallel Sail Blade (Do not use with the mulching baffle) Mulching Baffle Roller Scraper Grass Cutting: 1.9 to 4.4 cm (0.75 to 1.75 inch) Height-of-Cut Recommended in most applications May work well in light or sparse turf Grass Cutting: 5 to 6.4 cm (2.00 to 2.50 inch) Height-of-Cut Recommended for thick or lush turf Recommended for light or sparse turf Grass Cutting: 7 to 10 cm (2.75 to 4.
lush and dense grass you may have to raise the height–of–cut setting. Mowing with Sharp Blades A sharp blade cuts cleanly and without tearing or shredding the grass blades like a dull blade. Tearing and shredding causes the grass to turn brown at the edges which impairs growth and increases susceptibility to diseases. Always make sure blade is in good condition and a full sail is present. Checking the Condition of the Decks Make sure that the cutting chambers are in good condition.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first hour • Torque the wheel lug nuts to 94 to 122 N-m (70 to 90 ft-lb). After the first 10 hours • Torque the wheel lug nuts to 94 to 122 N-m (70 to 90 ft-lb). • Check the alternator belt tension. After the first 50 hours • Change the engine oil and filter.
Daily Maintenance Checklist Duplicate this page for routine use. For the week of: Mon. Maintenance Check Item Tues. Wed. Thurs. Fri. Sat. Sun. Check the safety interlock operation. Check the brake operation. Check the engine oil and fuel level. Drain the water/fuel separator. Check the air filter restriction indicator. Check the radiator and screen for debris. Check unusual engine noises.1 Check unusual operating noises. Check the hydraulic system oil level. Check the hydraulic filter indicator.
Service Interval Chart decal125-2927 Figure 46 CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance. Lubrication Greasing the Bearings and Bushings If you operate the machine under normal conditions, lubricate all grease fittings for the bearings and bushings after every 50 hours of operation with No. 2 General Purpose Lithium Base Grease.
• Cutting unit lift arm cylinders (2 each) (Figure 48) g011612 Figure 48 • Lift arm pivots (1 each) (Figure 48) • Cutting unit carrier frame pivot (1 each) (Figure 49) g003987 Figure 51 • Axle steering pivot (1) (Figure 52) g011613 Figure 49 g004169 Figure 52 • Lift arm pivot shaft (1 each) (Figure 50) • Steering cylinder ball joints (2) and rear axle (1) (Figure 53) g004157 Figure 50 • Rear axle tie rod (2) (Figure 51) g011614 Figure 53 43
Engine Maintenance • Brake pedal (1) (Figure 54) Servicing the Air Cleaner Check the air cleaner body for damage which could cause an air leak. Replace if damaged. Check the whole intake system for leaks, damage or loose hose clamps. g011615 Figure 54 Service the air cleaner filter only when the service indicator (Figure 57) requires it. Changing the air filter before it is necessary only increases the chance of dirt entering the engine when the filter is removed.
Checking the Engine-Oil Level Service Interval: Before each use or daily The engine is shipped with oil in the crankcase; however, the oil level must be checked before and after the engine is first started. Important: Check the engine oil daily. If the engine-oil level is above the Full mark on the dipstick, the engine oil may be diluted with fuel; If the engine oil level is above the Full mark, change the engine oil. g021218 Figure 58 1. Air cleaner cover 2. Air cleaner filter 3.
Crankcase Oil Capacity Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter Approximately 5.2 L (5.5 US qt) with the filter. Changing the Engine Oil and Filter Service Interval: Every 6,000 hours or clean the soot filter if engine faults SPN 3720 FMI 16, SPN 3720 FMI 0, or SPN 3720 FMI 16 display in the InfoCenter. • If advisory message ADVISORY 179 displays in the InfoCenter, the DPF is nearing the recommended point for servicing the diesel-oxidation catalyst and the soot filter.
Fuel System Maintenance DANGER Under certain conditions, diesel fuel and fuel vapors are highly flammable and explosive. A fire or explosion from fuel can burn you and others and can cause property damage. • Use a funnel and fill the fuel tank outdoors, in an open area, when the engine is off and is cold. Wipe up any fuel that spills. • Do not fill the fuel tank completely full. Add fuel to the fuel tank until the level is 6 to 13 mm (1/4 to 1/2 inch) below the bottom of the filler neck.
2. Remove the filter and clean the filter head mounting surface (Figure 64). 3. Lubricate the filter gasket with clean lubricating engine oil. Refer to the Engine Operator's Manual, included with the machine, for additional information. 4. Install the dry filter canister, by hand, until the gasket contacts the filter head, then rotate it an additional 1/2 turn. 5. Start the engine and check for fuel leaks around the filter head.
Checking the Fuses Drive System Maintenance There are 8 fuses in the electrical system. The fuse block (Figure 65) is located behind the control arm access panel. Adjusting the Traction Drive for Neutral The machine must not creep when the traction pedal is released. If it does creep, adjust as follows: 1. Park the machine on a level surface, stop the engine, and lower the cutting decks to the floor. 2. Jack up the machine until all the tires are off the shop floor.
6. Stop the engine. Remove the jack stands and lower the machine to the shop floor. 7. Test drive the machine to make sure it does not creep. Cooling System Maintenance Removing Debris from the Cooling System Adjusting the Rear Wheel Toe-in 1. Rotate the steering wheel so that the rear wheels are straight ahead. 2. Loosen the jam nut on each end of the tie rod (Figure 68). Remove debris from the screen and radiator/oil cooler daily (clean more frequently in dirty conditions). 1.
Brake Maintenance Adjusting the Parking Brakes Adjust the brakes when there is more than 2.5 cm (1 inch) of free travel (Figure 71) of the brake pedal, or when more holding force is required. Free travel is the distance the brake pedal moves before you feel braking resistance. g022306 Figure 70 1. Radiator/oil cooler g026816 5. Close the screen and secure the latch. Figure 71 1.
Belt Maintenance that the cable conduit does not rotate during tightening procedure. Servicing the Alternator Belt Adjusting the Parking Brake Latch Service Interval: After the first 10 hours If the parking brake fails to engage and latch, an adjustment to the brake pawl is required. 1. Every 100 hours Loosen the 2 screws securing the parking brake pawl to the frame (Figure 73). Check the condition and tension of the belt (Figure 74) after every 100 operating hours. 1.
Hydraulic System Maintenance 9. Check the level of the hydraulic fluid and add enough to raise level to the Full mark on the dipstick. Important: Do not over-fill. Changing the Hydraulic Fluid Replacing the Hydraulic Filters Change hydraulic fluid after every 800 operating hours, in normal conditions. If fluid becomes contaminated, contact your local Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. 1.
Checking the Hydraulic Lines and Hoses Daily, check hydraulic lines and hoses for leaks, kinked lines, loose mounting supports, wear, loose fittings, weather deterioration, and chemical deterioration. Make all necessary repairs before operating. WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
Mounting the Cutting Decks to the Traction Unit Cutting Deck Maintenance 1. Separating the Cutting Decks from the Traction Unit 2. 3. 1. Position the machine on a level surface, lower the cutting decks to the floor, shut the engine off, and engage the parking brake. 4. 2. Disconnect and remove the hydraulic motor from the deck (Figure 79). Cover the top of the spindle to prevent contamination. 5. Position machine on a level surface and shut engine off.
5. Rotate the marked end of the blade to the 3 and 9 o’clock positions (Figure 81) and measure the heights. 6. Compare the 12 o’clock measured height to the height-of-cut setting. It should be within 0.7 mm (0.030 inch). The 3 and 9 o’clock heights should be 3.8±2.2 mm (0.150±.090 inch) higher than the 12 o’clock setting and within 2.2 mm (0.090 inch) of each other. height then no adjustment is needed for that side. Adjust the other side to within ±2.2 mm (0.090 inch) of the correct side. 7.
DANGER A worn or damaged blade can break, and a piece of the blade could be thrown into the operator’s or bystander’s area, resulting in serious personal injury or death • Inspect the blade periodically for wear or damage. • Never weld a broken or cracked blade. g006924 Figure 84 • Always replace a worn or damaged blade. 1. Cutting edge 3. Wear/slot/crack 2. Sail Inspecting and Sharpening the Blade 1. Raise the cutting deck to the highest position, shut the engine off, and engage the parking brake.
4. To verify this stopping time, have a second person stand back from the deck at least 6 m (20 feet) and watch the blades on one of the cutting decks. Have the operator shut the cutting decks down and record the time it takes for the blades to come to a complete stop. If this time is greater than 7 seconds, the braking valve needs adjustment. Call your Toro Distributor for assistance in making this adjustment. Important: Securing the roller assembly with a gap larger than 1.5 mm (0.
Storage Storing the Cutting Deck Preparing the Traction Unit If the cutting deck is separated from the traction unit for any length of time, install a spindle plug in the top of the spindle to protect the spindle from dust and water. 1. Thoroughly clean the traction unit, cutting decks, and engine. 2. Check the tire pressure. Inflate all traction unit tires to 83 to 103 kPa (12 to 15 psi). 3. Check all fasteners for looseness and tighten them as necessary. 4.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).