Form No. 3406-140 Rev B Groundsmaster® 4500-D and 4700-D Traction Unit Model No. 30873—Serial No. 316000001 and Up Model No. 30874—Serial No. 316000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. Figure 1 1.
Contents Greasing the Bearings and Bushings ..........................41 Engine Maintenance ..................................................42 Engine Safety.........................................................42 Servicing the Air Cleaner .........................................42 Servicing the Engine Oil..........................................43 Fuel System Maintenance ...........................................45 Servicing the Water Separator...................................
Sound Power Level Safety Model 30873 This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. This unit has a guaranteed sound power level of 104 dBA, which includes an Uncertainty Value (K) of 0.7 dBA. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means Caution, Warning, or Danger—personal safety instruction.
Vibration Level Hand-Arm Model 30873 Measured vibration level for right hand = 0.8 m/s2 Measured vibration level for left hand = 0.8 m/s2 Uncertainty Value (K) = 0.4 m/s2 Measured values were determined according to the procedures outlined in EN ISO 5395:2013. Model 30874 Measured vibration level for right hand = 0.4 m/s2 Measured vibration level for left hand = 0.4 m/s2 Uncertainty Value (K) = 0.2 m/s2 Measured values were determined according to the procedures outlined in EN ISO 5395:2013.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7818 1. Warning—read the Operator's Manual for instructions on torquing the blade bolt/nut to 115 to 149 N∙m (85 to 110 ft-lb). 117-4763 1. To engage the parking 2.
117-4765 1. Read the Operator's Manual. 2. Do not use starting aids. 117-4766 1. Cutting/dismemberment hazard; fan—stay away from moving parts, keep all guards and shields in place. 120-4159 1. Off 2. Lights 3. On 4. Light-switch location 8. High 9. Traction drive 10. Low 11. Power takeoff (PTO) 5. Fast 12. Lower, left deck 6. Variable-speed adjustment 13. Lower, center deck 7. Slow 14. Lower, right deck Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6.
125-4604 For Model 30874 3. Raise the right deck. 1. Raise the left deck. 2. Raise the center deck. 125-4605 1. Power seat—10 A 6. Power supplied—10 A 2. Work light—10 A 7. GM4700 controller—2 A 3. Engine—10 A 8. Power supplied—7.5 A 4. Power port—10 A 5. Infocenter—2 A 121-3887 1. Read the Operator’s Manual. 125-4603 For Model 30873 1. Raise the decks. 8 9. GM4500 controller—2 A 10.
125-4606 1. Read the Operator’s Manual for information on maintenance. 121–3627 1.
127-6447 For Model 30873 1. Warning—read the Operator’s Manual; do not operate the machine unless you have received training. 2. Warning—read the Operator’s Manual for information on towing. 3. Tipping hazard—do not 5. Warning—do not park on drive on slopes greater than slopes; 1) Engage the 16 degrees. parking brake, 2) Lower the decks, 3) Turn off the engine. 4) Remove the key from the ignition, 5) Leave the machine. 4. Keep the decks lowered 6.
127-6448 For Model 30874 1. Warning—read the Operator’s Manual; do not operate the machine unless you have received training. 2. Warning—read the Operator’s Manual for information on towing. 3. Tipping hazard—do not 5. Warning—do not park on drive on slopes greater than slopes; 1) Engage the 21 degrees. parking brake, 2) Lower the decks, 3) Turn off the engine. 4) Remove the key from the ignition, 5) Leave the machine. 4. Keep the decks lowered 6.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Prepare the machine. 2 Lock bracket Rivet Washer Screw (1/4 x 2 inches) Locknut (1/4 inch) 1 2 1 1 1 Install the hood latch (CE). Media and Additional Parts Description Use Qty. Operator's Manual 1 Read this before operating the machine. Engine Operator's Manual 1 Read this before operating the engine.
2. Remove the 2 rivets securing the hood-latch bracket to the hood (Figure 3). 1 1 2 Preparing the Machine No Parts Required Checking the Fluid Levels 1. Check the rear-axle lubricant level before the engine is first started, refer to Checking the Rear-Axle Lubricant (page 50). 2. Check the engine-oil level before starting the engine; refer to Checking the Engine-Oil Level (page 43). G012628 Figure 3 3.
1. Loosen the grease fitting and the mounting screw (Figure 7). 1 1 2 3 G012630 G011346 Figure 7 Figure 5 1. Roller scraper 1. Hood latch 9. Assemble the bolt through the other arm of CE-lock bracket and secure the bolt with the locknut and washer (Figure 6). 2. Slide the scraper up or down until a gap of 0.5 to 1 mm (0.020 to 0.040 inch) is achieved between the rod and the roller. Note: Tighten the bolt securely but do not tighten the nut.
4 Installing the Mulching Baffle Parts needed for this procedure: 5 or 7 Mulching baffle—optional Toro part Procedure DANGER Using the high-lift blade with the mulching baffle could cause the blade to break, resulting in personal injury or death. Do not use the high-lift blade with the mulching baffle. 1. Thoroughly clean debris from the mounting holes on the rear wall and left side wall of the chamber. 2. Install the mulching baffle in the rear opening and secure it with 5 flange-head bolts (Figure 8).
Product Overview Note: In emergency braking situations, press the service brake pedals in addition to using the reverse pedal as stated above. This is the quickest method to stop the machine. Controls Tilt-Steering Pedal Brake Pedals To adjust the tilt the steering wheel, press down the tilt-steering pedal (Figure 9), and adjust the steering wheel and column to a comfortable operating position, and then release the pedal.
High/Low-Speed Control The switch (Figure 10) allows the speed range to increase for transport of the machine. The mower decks do not operate in the high-speed range. Also, you cannot lower the decks from the transport position when the switch is in the high range. Engine-Speed Switch The engine-speed switch (Figure 10) has 2 modes to change the engine speed. By momentarily tapping the switch, you can increase or decrease the engine speed in 100 rpm increments.
Weight Gauge Indicates when the seat is adjusted to your weight (Figure 13). You can make height adjustments by positioning the suspension within the range of the green region. Weight-Adjusting Lever Adjust for your weight (Figure 13). Pull up the lever to increase the air pressure, and push down the lever to decrease the air pressure. You attain the proper adjustment when the weight gauge is in the green region.
Specifications Figure 14 19
Machine Specifications Description Model 30873 Figure 14 reference Model 30874 Figure 14 reference Width of cut 280 cm (110 inches) D 380 cm (150 inches) F Mower decks down 294 cm (116 inches) E 402 cm (158 inches) G Mower decks up (transport) 213 cm (105 inches) A 213 cm (105 inches) A Front 224 cm (88 inches) B 224 cm (88 inches) B Rear 141 cm (56 inches) M 141 cm (56 inches) M 216 cm (85 inches) C 216 cm (85 inches) C Mower decks down 370 cm (146 inches) H 370 cm (146
Fuel Safety Operation DANGER Note: Determine the left and right sides of the machine from the normal operating position. In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Before Operation • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills. Before Operation Safety • Never fill the fuel tank inside an enclosed trailer.
Checking the Engine-Oil Level Biodiesel Ready Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 43). This machine can also use a biodiesel blended fuel of up to B20 (20% biodiesel, 80% petrodiesel). The petrodiesel portion should be low or ultra-low sulfur.
Checking the Air Pressure in the Tires Service Interval: Before each use or daily DANGER Low tire pressure decreases machine side-hill stability. This could cause a rollover, which may result in personal injury or death. Do not under-inflate the tires. The correct air pressure in the tires is 138 kPa (20 psi). Important: Maintain the recommended pressure in all tires to ensure a good quality of cut and proper machine performance. Do not under-inflate the tires.
Figure 17 Front Wheels Figure 19 1. Height-of-cut bracket 3. Spacer 2. Height-of-cut plate 4. While supporting the chamber, remove the spacer (Figure 19). 5. Move the chamber to the desired height of cut and install a spacer into the designated height-of-cut hole and slot (Figure 20). Figure 18 Rear Wheels Adjusting the Height-of-Cut Important: This cutting deck often cuts approximately 6 mm (1/4 inch) lower than a reel cutting unit with the same bench setting.
Checking the Interlock Switches Using the InfoCenter LCD Display Service Interval: Before each use or daily The InfoCenter LCD display shows information about your machine such as the operating status, various diagnostics and other information about the machine (Figure 21). There is a splash screen and main information screen of the InfoCenter. Press any of the InfoCenter buttons and then select the appropriate directional arrow to switch between the splash screen and the main information screen.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.) Indicates when scheduled service should be performed Engine rpm/status—indicates the engine speed in rpm The engine is shut off. Info icon Engine Sets the maximum traction speed Key switch Fast Mower decks are lowering. Mower decks are raising. Slow PIN passcode The fan is reversed. Hydraulic fluid temperature CAN bus Stationary regeneration is required. InfoCenter The air intake heater is active.
Service InfoCenter Icon Description (cont'd.) Menu Item Description Hours Lists the total number of hours that the machine, engine and fan have been on, as well as the number of hours the machine has been transported and overheated. Counts Lists the number of starts, deck PTO cycles and fan reversals the machine has experienced. Engine start is denied. Engine shutdown Engine coolant is too hot. Hydraulic fluid is too hot. Diagnostics DPF ash accumulation notification.
Setting the Maximum Allowed Mow Speed About Menu Item Description Model Lists the model number of the machine. 1. In the Settings Menu, scroll down to Mow Speed and press the right button. SN Lists the serial number of the machine. 2. Set the maximum allowed mow speed. S/W Rev Lists the software revision of the master controller. Note: Press the right button to increase the max full mow speed (50%, 75%, or 100%). Press the center button to decrease the max full mow speed (50%, 75%, or 100%).
Selecting a Blade Standard Combination Sail This blade was designed to provide excellent lift and dispersion in almost any condition. If more or less lift and discharge velocity is required, consider a different blade. Attributes: Excellent lift and dispersion in most conditions. Angled Sail The blade generally performs best in lower heights of cut– 1.9 to 6.4 cm (3/4 to 2-1/2 inches). Attributes: • Discharge remains more even at lower heights of cut.
Choosing Accessories Optional Equipment Configurations Angle Sail Blade High-Lift, Parallel Sail Blade (Do not use with the mulching baffle) Mulching Baffle Roller Scraper Grass Cutting: 1.9 to 4.4 cm (3/4 to 1-3/4 inches) height-of-cut Recommended in most applications May work well in light or sparse turf Use the scraper any time that rollers buildup with grass or large flat grass clumps of grass are seen. Grass Cutting: 5 to 6.
Slope Safety • Stop the machine and inspect the blades after striking an object or if there is an abnormal vibration in the machine. Make all necessary repairs before resuming operation. • Slow down the machine and use extra care on hillsides. Travel in the recommended direction on hillsides. Turf conditions can affect the stability of the machine. • Stop the blades whenever you are not mowing, especially while crossing loose terrain such as gravel.
is buckled. Drive slowly and avoid sharp turns on slopes to prevent rollovers. For steering control, the mower decks it must be lowered when going downhill. CAUTION Checking the machine for oil leaks, loose parts, and other malfunctions while the engine is running may bring you in close contact with hot or moving parts of the machine, causing injury. Important: Allow engine to idle for 5 minutes before shutting it off after a full load operation.
Operating Tips Resolving Aftercut Appearance Mowing When Grass Is Dry Reference the Aftercut Appearance Troubleshooting Guide available at www.Toro.com. Mow either in the late morning to avoid the dew, which causes grass clumping, or in late afternoon to avoid the damage caused by direct sunlight on the sensitive, freshly mowed grass. Transporting the Machine Lock the brake pedals together with the pedal-locking latch while transporting the machine. Using the Transport Latches Model No.
system, prevents wear on system parts, and also prevents accidental lowering of the mower decks. After Operation After Operation Safety General Safety • Clean grass and debris from the mower decks, drives, muffler, and engine to help prevent fires. Clean up oil or fuel spills. • Ensure that the PTO is shut off before you are transporting or not using the machine. • Allow the engine to cool before storing the machine in any enclosure.
Figure 26 1. Bypass valve (2) 3. Close the bypass valves before starting the engine. Torque to 70 N∙m (52 ft-lb) to close the valve. Hauling the Machine • Use care when loading or unloading the machine into a trailer or a truck. • Use full-width ramps for loading the machine into a trailer or a truck. • Tie the machine down securely using straps, chains, cable, or ropes. Both front and rear straps should be directed down and outward from the machine.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Torque the wheel-lug nuts. After the first 200 hours Before each use or daily • Change the gear lubricant of the planetary-gear-drives. • Change the rear-axle lubricant. • Change the hydraulic filters. • • • • • • • • • • Check the tire pressure. Check the interlock switches.
Duplicate this page for routine use. Daily Maintenance Checklist For the week of: Maintenance Check Item Monday Tuesday Wednesday Thursday Friday Saturday Sunday Check the safety-interlock operation. Check the brake operation. Check the engine-oil level. Check the cooling-system-fluid level. Drain the water/fuel separator. Check the air filter, dust cup, and burp valve. Check for unusual engine noises.2 Check the radiator and screen for debris Check for unusual operating noises.
Service Interval Chart Figure 27 CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition switch before you perform any maintenance.
Premaintenance Procedures Preparing the Machine for Maintenance 1. Ensure that the PTO is disengaged. 2. Park the machine on a level surface. Pre-Maintenance Safety 3. Set the parking brake. • Keep all parts of the machine in good working condition 4. Lower the mower deck(s) if necessary. and all hardware tightened, especially blade-attachment hardware. Replace all worn or damaged decals. 5. Shut off the engine and wait for all moving parts to stop.
Accessing the Hydraulic Lift Compartment Tilt the seat to access the hydraulic lift compartment as shown in Figure 31. Figure 29 Opening the Hood Tilt the hood to access the chassis as shown in Figure 30.
Lubrication • Steering-cylinder ball joints (2) as shown in Figure 34 Greasing the Bearings and Bushings Service Interval: Every 50 hours (And after every washing). Grease specification: No. 2 lithium grease The grease fitting locations and quantities are as follows: • Brake-shaft pivot bearings (5) as shown in Figure 32 Figure 32 Figure 34 1.
Engine Maintenance • Cutting-unit spindle-shaft bearings (2 per mower deck) as shown in Figure 36 Note: You can use either fitting, whichever is more accessible. Pump grease into the fitting until a small amount appears at bottom of the spindle housing (under the deck). Engine Safety Shut off the engine before checking the oil or adding oil to the crankcase. Servicing the Air Cleaner Service Interval: Every 400 hours Check the air-cleaner body for damage that could cause an air leak.
Figure 40 1. Air-cleaner safety filter 2. Reset the indicator (Figure 38) if it shows red. Servicing the Engine Oil Checking the Engine-Oil Level Service Interval: Before each use or daily Crankcase oil capacity: approximately 9.5 L (10 US qt) with the filter. Oil specification: API classificationCH-4, CI-4, or higher.
Changing the Engine Oil and Filter Service Interval: Every 250 hours 1. Start the engine and let it run 5 minutes to allow the oil to warm up. 2. With the machine parked on a level surface, shut off the engine, remove the key from the key switch, and wait for all moving parts to stop before leaving the operating position. 3. Replace the engine oil and filter (Figure 42). Figure 41 Note: When using different oil, drain all old oil from the crankcase before adding new oil. Figure 42 4.
Inspecting the Fuel Lines and Connections Fuel System Maintenance Service Interval: Every 400 hours—Inspect the fuel lines and connections. Servicing the Water Separator Yearly—Inspect the fuel lines and connections. Service Interval: Before each use or daily—Drain water or other contaminants from the fuel filter/water separator. Inspect the fuel lines and connections for deterioration, damage, or loose connections. Every 400 hours—Replace the fuel-filter canister.
Electrical System Maintenance 5. Insert the fuel-pickup tube through the rubber bushing and into the tank (Figure 44). Note: Ensure that the fuel-pickup tube is fully seated into the rubber bushing. 6. Install the supply hose onto the fitting of the fuel-pickup tube, and secure the hose with the hose clamp that you removed in step 1. Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last.
Locating the Fuses The fuse block for the machine is located in the right storage box Figure 48 1. Fuses 3. Close the cover of the right storage box and secure the cover with the latch (Figure 47). Figure 46 Checking the Battery Condition 1. Loosen the latch for the cover of the right storage box and raise the cover (Figure 47) to expose the fuse block (Figure 48).
WARNING Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Always connect the positive (red) battery cable before connecting the negative (black) cable. 3. Connect a 3 to 4 A battery charger to the battery posts. 4. Charge the battery at a rate of 3 to 4 A for 4 to 8 hours. 5.
Drive System Maintenance Checking the Planetary-Gear-Drive Lubricant Checking for End-Play in the Planetary Drives Service Interval: Every 400 hours—Check the lubricant level of the planetary-gear-drives (also check if you observe external leakage). Service Interval: Every 400 hours Lubricant specification: high-quality SAE 85W-140 gear lubricant There should be no end-play in the planetary drives/drive wheels (i.e.
Changing the Planetary-Gear-Drive Lubricant. 6. Through the open hole, slowly fill the planetary with 0.65 L (22 oz) of high-quality SAE 85W-140 gear lube. Important: If the planetary fills before the 0.65 L (22 oz) of oil is added, wait 1 hour or install the plug and move the machine approximately 3 m (10 ft) to distribute the gear lubricant through the brake system. Then, remove the plug and add the remaining gear lubricant.
Checking the Rear Axle-Gearbox Lubricant Service Interval: Every 400 hours Check the lubricant level before the engine is first started and every 400 hours thereafter. Lubricant specification: high-quality SAE 85W-140 gear lubricant Axle capacity: 0.5 L (16 oz) 1. Position the machine on a level surface. Figure 56 2. Remove the check/fill plug from the left side of the gearbox (Figure 52) and make sure that lubricant is up to the bottom of the hole.
Cooling System Maintenance Cooling System Safety CAUTION Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. Figure 59 1. Front of machine 2. 3 mm (1/8 inch) less than rear of tire 3. Center-to-center distance • Do not remove the radiator cap when the engine is hot. Always allow the engine to cool at least 15 minutes or until the radiator cap is cool enough to touch without burning your hand before removing the radiator cap. 2.
Cleaning the Cooling System Service Interval: Before each use or daily—Remove debris from the engine area, oil cooler, and radiator. Clean them more frequently in dirty conditions. This machine is equipped with a hydraulically driven fan drive system that automatically (or manually) reverses to reduce oil cooler/radiator and screen debris build-up. While this feature can help reduce the time required to clean oil cooler/radiator, it does not eliminate the need for routine cleaning.
Brake Maintenance Adjusting the Service Brakes Adjust the service brakes when there is more than 25 mm (1 inch) of free travel of the brake pedal, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before braking resistance is felt. 1. Release the locking latch from the brake pedals so that both pedals work independently of each other. 2. To reduce free travel of the brake pedals, tighten the brakes: A.
Belt Maintenance Hydraulic System Maintenance Servicing the Alternator Belt Hydraulic System Safety Service Interval: Every 100 hours 1. Check the tension of the alternator belt by depressing it midway between the alternator and the crankshaft pulleys with 4.5 kg (10 lb) of force. WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Note: The belt should deflect 10mm (3/8 inch). If the deflection is incorrect, proceed to step 2. If correct, continue operation.
High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 Material Properties: Viscosity, ASTM D445 Viscosity Index ASTM D2270 Pour Point, ASTM D97 Industry Specifications: cSt @ 40°C (104°F) 44 to 48 cSt @ 100°C (212°F) 7.9 to 9.1 140 to 160 -37°C to -45°C (-34°F to -49°F) Vickers I-286-S (Quality Level), Vickers M-2950-S (Quality Level), Denison HF-0 Important: The ISO VG 46 Multigrade fluid has been found to offer optimal performance in a wide range of temperature conditions.
Changing the Hydraulic Fluid Replacing the Hydraulic Filters Service Interval: Every 800 hours Service Interval: After the first 200 hours Every 800 hours If the fluid becomes contaminated, contact your Toro Distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean hydraulic fluid. Use Toro replacement filters Part No. 94-2621 for the rear (mower decks) of the machine and Part No. 75-1310 for the front (charge) of the machine. 1.
Checking the Hydraulic Lines and Hoses Service Interval: Before each use or daily Inspect the hydraulic lines and hoses daily for leaks, kinked lines, loose mounting supports, wear, loose fittings, weather deterioration, and chemical deterioration. Make all necessary repairs before operating the machine. Figure 68 3. Lower and secure the operator’s seat. 4. Replace the return filter at the right side of the machine (Figure 68). 5.
Mower Deck Maintenance Assembling the Mower Decks to the Machine 1. Move the mower deck into position in front of the machine. Separating the Mower Decks from the Machine 2. Slide the deck carrier frame onto the lift-arm-pivot pin (Figure 70). Secure the deck to the pin with the lynch pin (or retaining nut—model 30874). 1. Disconnect and remove the hydraulic motor from the deck (Figure 69). Cover the top of the spindle to prevent contamination. 3. Install the hydraulic motor to the deck (Figure 69).
Blade Maintenance Assembling the Front Roller 1. Press the first bearing into the roller housing (Figure 71). Press on the outer race only or equally on the inner and outer race. Blade Safety 2. Insert the spacer (Figure 71). DANGER 3. Press the second bearing into the roller housing (Figure 71).Pressing equally on the inner and outer race until the inner race comes in contact with the spacer.
12:00 Note: Socket-head bolt/spacer are held together with thread-locking adhesive to prevent the spacer from falling inside the deck frame. 5. Verify the 12 o’clock height and adjust if needed. 6. Determine if only 1 or both (right and left) height-of-cut brackets need to be adjusted. 3:00 9:00 6:00 Figure 72 Note: If the 3 or 9 o’clock side is 3.8 ± 2.2 mm (0.150 ± 0.090 inch) higher than the new front height then no adjustment is needed for that side. Adjust the other side to within ± 2.2 mm (0.
DANGER A worn or damaged blade can break, and a piece of the blade could be thrown into the operator’s or bystander’s area, resulting in serious personal injury or death Figure 76 • Inspect the blade periodically for wear or damage. 1. Sharpen at this angle only • Never weld a broken or cracked blade. 5. To check the blade for being straight and parallel, lay the blade on a level surface and check its ends.
Storage Preparing the Mower Deck Preparing the Machine If the mower deck is removed from the machine for any length of time, install a spindle plug into the top of the spindle housing to protect the spindle socket from dust and water. 1. Thoroughly clean the chassis of the machine, mower decks, and the engine. 2. Check the tire pressure; refer to Checking the Air Pressure in the Tires (page 23). 3. Check all fasteners for looseness; tighten as necessary. 4.
Notes:
Notes:
Notes:
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
