Form No. 3401-829 Rev C Groundsmaster® 4500-D and 4700-D Traction Unit Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 30881—Serial No. 315000001 and Up 30881A—Serial No. 315000001 and Up 30882—Serial No. 315000001 and Up 30882A—Serial No.
This product complies with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
Contents Engine Safety ................................................... 46 Servicing the Air Cleaner .................................. 46 Servicing the Engine Oil.................................... 47 Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter .............................. 48 Fuel System Maintenance ................................... 49 Draining the Fuel Tank ...................................... 49 Inspecting the Fuel Lines and Connections....................................
Safety Sound Power Level This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. This unit has a guaranteed sound power level of 105 dBA, which includes an Uncertainty Value (K) of 0.7 dBA. General Safety Sound power level was determined according to the procedures outlined in ISO 11094. This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal93-6681 93-6681 1. Cutting/dismemberment—hazard, fan-stay away from moving parts. decal106-6754 106-6754 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. decal93-7272 93-7272 1.
decal117-2718 117-2718 decal112-5297 112-5297 1. Warning—read the Operator's Manual, do not operate this machine unless you are trained. 2. Warning—read the Operator's Manual before towing the machine. 3. Tipping hazard—slow machine before turning, do not turn at high speeds; lower the cutting unit when driving down slopes; use a rollover protection system and wear the seat belt 4.
decal117-4765 117-4765 1. Read the Operator's Manual. 2. Do not use starting aids. decal121-3884 121-3884 decal117-4766 117-4766 1. Engine—stop 1. Cutting/dismemberment hazard; fan—stay away from moving parts, keep all guards and shields in place. 3. Engine—start 2. Engine—preheat decal121-3887 121-3887 1. Read the Operator’s Manual. decal120-4159 120-4159 Groundsmaster 4700 Shown 1. Off 2. Lights 3. On 4. Light switch location 8. High 9. Traction drive 10. Low 11. Power takeoff (PTO) 5.
decal125-4605 125-4605 1. Power seat—10 A 6. Power supplied—10 A 2. Work light—10 A 7. TEC-5001—2 A 3. Engine—10 A 8. Power supplied—7.5 A 4. Cigarette lighter—10 A 9. TEC-5002—2 A 5. Infocenter—2 A decal125-4606 125-4606 1. Read the Operator’s Manual for information on maintenance. 10. Cab—60 A decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking 7.
decal104-1086 104-1086 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 Use Qty. Lock bracket Rivet Washer Screw (1/4 x 2 inches) Locknut (1/4 inch) 1 2 1 1 1 Install the hood latch (CE). No parts required – Adjust the roller scraper (optional). No parts required – Install the mulching baffle (optional). No parts required – Prepare the machine. Media and Additional Parts Description Use Qty.
1 1 2 Installing the Hood Latch (CE Only) Parts needed for this procedure: G012629 1 Lock bracket 2 Rivet 1 Washer 1 Screw (1/4 x 2 inches) 1 Locknut (1/4 inch) g012629 Figure 4 1. CE lock bracket 4. Align the washers with the holes on the inside of the hood. Procedure 5. Rivet the brackets and the washers to the hood (Figure 4). 1. Unhook the hood latch from the hood-latch bracket. 6. Hook the latch onto the hood-latch bracket (Figure 5). 2.
3 3 Installing the Mulching Baffle (Optional) 2 1 No Parts Required G012631 g012631 Figure 6 1. Bolt 2. Nut Procedure 3. Arm of hood-lock bracket 1. Thoroughly clean debris from the mounting holes on the rear wall and left side wall of the chamber. 2. Install the mulching baffle in the rear opening and secure it with 5 flange-head bolts (Figure 8).
Product Overview 4 Controls Preparing the Machine Brake Pedals 2 foot pedals (Figure 9) operate individual wheel brakes for turning assistance and to aid in obtaining better side hill traction. No Parts Required Checking the Tire Pressure Pedal-Locking Latch Check the tire pressure before use; refer to Checking the Tire Pressure (page 23). Important: Maintain pressure in all tires to ensure a good quality-of-cut and proper machine performance. Do not underinflate the tires.
Note: In emergency braking situations, press the service brake pedals in addition to using the reverse pedal as stated above. This is the quickest method to stop the machine. engage the cutting unit blades. Push in the button to disengage the cutting unit blades. Tilt-Steering Pedal To tilt the steering wheel toward you, press the foot pedal (Figure 9) down, and pull the steering tower toward you to the most comfortable position and then release the pedal.
Bag Holder Using the InfoCenter LCD Display Use the bag holder (Figure 11) for storage. The InfoCenter LCD display shows information about your machine, such as the operating status, various diagnostics and other information about the machine (Figure 13). There is a splash screen and main information screen of the InfoCenter. You can switch between the splash screen and main information screen at any time by pressing any of the InfoCenter buttons and then selecting the appropriate directional arrow.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.) Indicates when scheduled service should be performed The status of the engine rpm. The cruise control is on. Info icon Stop the engine. Maximum traction speed setting Engine Fast Key switch Cutting units are lowering. Slow Cutting units are raising. The fan is reversed. PIN code Hydraulic fluid temperature Stationary regeneration is required. CAN bus The air-intake heater is active InfoCenter Raise the left deck.
InfoCenter Icon Description (cont'd.) Service Menu Item Description Hours Lists the total number of hours that the machine, engine and fan have been on, as well as the number of hours the machine has been transported and overheated. Counts Lists the number of starts, deck PTO cycles, and fan reversals the machine has experienced. Symbols are often combined to form sentences. Some examples are shown below Operator should put machine in neutral. Engine start is denied. Diagnostics Engine shutdown.
About Menu Item Description Model Lists the model number of the machine. SN Lists the serial number of the machine. S/W Rev Lists the software revision of the master controller. Protected Menus There are 5 operating configuration settings that are adjustable within the Settings Menu of the InfoCenter: auto idle, maximum mowing ground speed, maximum transport ground speed, Smart Power, and deck counter balance. These settings are in the Protected Menu.
Setting the Counterbalance Viewing and Changing the Protected Menu Settings 1. In the Settings Menu, scroll down to Counter Balance and press the right button. 1. In the Protected Menu, scroll down to Protect Settings. 2. Press the right button to switch between Low, Med, and High. 2. To view and change the settings without entering a passcode, use the right button to change the Protect Settings to OFF.
Specifications Note: Specifications and design are subject to change without notice. 4500-D 4700-D Width of cut 2.8 m (109 inches) 3.8 m (150 inches) Overall width, cutting units down 286 cm (112.8 inches) 391 cm (153.8 inches) Overall width, cutting units up (transport) 224 cm (88.25 inches) 224 cm (88.25 inches) Overall length 370 cm (145.8 inches) 370 cm (145.
Fuel Safety Operation DANGER Note: Determine the left and right sides of the In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills. • Never fill the fuel tank inside an enclosed trailer. • Never smoke when handling fuel, and stay away from an open flame or where fuel fumes may be ignited by a spark.
Fuel Table overfill the fuel tank. Replace the fuel-tank cap and tighten it securely. Diesel fuel specification Location Checking the Engine-Oil Level ASTM D975 Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 47). EN 590 European Union ISO 8217 DMX International JIS K2204 Grade No. 2 Japan KSM-2610 Korea No. 1-D S15 USA No.
Adding Fuel Checking the Tire Pressure Service Interval: Before each use or daily The correct air pressure in the tires is 138 kPa (20 psi). Important: Maintain the recommended pressure in all tires to ensure a good quality of cut and proper machine performance. Do not under-inflate the tires. Check the air pressure in all the tires before operating the machine.
Adjusting the Height of Cut 7. Install the bolt finger-tight. 8. Repeat steps 4 through 7 for each side adjustment. Important: This cutting deck often cuts approximately 6 mm (1/4 inch) lower than a reel cutting unit with the same bench setting. It may be necessary to have these rotary cutting deck’s bench set 6 mm (1/4 inch) above that of reels cutting in the same area. 9. Torque all 3 bolts to 41 N∙m (30 ft-lb). Always tighten the front bolt first. Note: Adjustments of more than 3.
Note: The InfoCenter displays "traction denied" Attributes: and the machine should not move. If the machine does move, there is a malfunction in the interlock system. Correct this malfunction before operating the machine. • More lift and higher discharge velocity. • Sparse or limp turf is picked up significantly at higher heights of cut. • Wet or sticky clippings are discharged more Checking the Blade-Stopping Time efficiently reducing congestion in the deck. • Requires more horsepower to run.
Choosing Accessories Optional Equipment Configurations Angle Sail Blade High-Lift, Parallel-Sail Blade (Do not use with the mulching baffle) Mulching Baffle Roller Scraper Grass Cutting: 1.9 to 4.4 cm (0.75 to 1.75 inch) height of cut Recommended in most applications May work well in light or sparse turf Grass Cutting: 5 to 6.4 cm (2.00 to 2.50 inch) height of cut Recommended for thick or lush turf Recommended for light or sparse turf Grass Cutting: 7 to 10 cm (2.75 to 4.
During Operation • Turn on the flashing warning lights on the machine During Operation Safety • General Safety • • The owner/user can prevent and is responsible for accidents that may cause injuries to people, or damage to property. • • Wear appropriate clothing, including eye protection; substantial, slip-resistant footwear; and hearing protection. Tie back long hair. Do not wear jewelry.
• Avoid starting, stopping, or turning the machine CAUTION on a slope. If the tires lose traction, disengage the blade(s) and proceed slowly straight down the slope. Checking the machine for oil leaks, loose parts, and other malfunctions while the engine is running may bring you in close contact with hot or moving parts of the machine, causing injury. • Do not turn the machine sharply. Use care when reversing the machine.
Diesel Particulate Filter Regeneration Important: Minimize the amount of time that you idle the engine or operate the engine at low-engine speed to help reduce the accumulation of soot in the soot filter. The diesel particulate filter (DPF) is part of the exhaust system. The diesel-oxidation catalyst of the DPF reduces harmful gasses and the soot filter removes soot from the engine exhaust.
DPF Ash Accumulation • When enough ash accumulates, the engine • The lighter ash is discharged through the exhaust system; the heavier ash collects in the soot filter. • Ash is a residue of the regeneration process. Over • time, the diesel particulate filter accumulates ash that does not discharge with the engine exhaust. • • The computer for the engine calculates the amount of ash accumulated in the DPF.
Types of Diesel Particulate Filter Regeneration Types of diesel particulate filter regeneration that are performed while the machine is operating: Type of Regeneration Conditions for DPF regeneration DPF description of operation Passive Occurs during normal operation of the machine at high-engine speed or high-engine load The InfoCenter does not display an icon indicating passive regeneration.
Types of diesel particulate filter regeneration that require you to park the machine: (cont'd.) Type of Regeneration Conditions for DPF regeneration DPF description of operation Recovery Occurs as a result of ignoring parked regeneration requests and continuing operation, adding more soot when the DPF is already in need of a parked regeneration When the recovery-regeneration icon is displayed in the InfoCenter, a recovery regeneration is requested.
Reset Regeneration Parked Regeneration g214713 g214711 Figure 27 Assist/reset-regeneration icon Figure 28 Parked-regeneration request icon • The assist/reset-regeneration icon displays in the • The parked-regeneration requested icon displays InfoCenter (Figure 27). • • The computer takes control of the intake throttle and changes the fuel injection operation to increase the temperature of the engine exhaust. in the InfoCenter (Figure 28).
6. Engage the parking brake. 7. Set the throttle to the low IDLE position. Performing a Parked Regeneration Note: For instructions on unlocking protected menus, refer to Accessing Protected Menus (page 18). 1. Access the protected menu and unlock the protected settings submenu (Figure 30); refer to Accessing Protected Menus (page 18). g212138 Figure 32 4. When the “Initiate DPF Regen. Are you sure?” message displays, press the center button (Figure 33). g028523 Figure 30 2.
g211986 g212405 Figure 34 Figure 36 6. Move the throttle control to LOW IDLE and press the center button (Figure 35). B. The “Waiting on (Figure 37). ” message displays g212372 g212406 Figure 35 Figure 37 7. The following messages display as the parked regeneration process begins: C. The computer determines whether the regeneration runs. One of the following messages displays in the InfoCenter: A. The “Initiating DPF Regen.” message displays (Figure 36).
The engine is cold—wait. The engine is warm—wait. The engine hot—regeneration in progress (percent complete). 9. The parked regeneration is complete when the “Regen Complete” message displays in the InfoCenter. Press the left button to exit to the home screen (Figure 40). g213424 Figure 38 • If the regeneration process is not allowed by the engine computer, the “DPF Regen Not Allowed” message displays in the InfoCenter (Figure 39).
Operating the Engine-Cooling Fan • Perform a recovery-regeneration whenever there is a loss of engine power and a parked regeneration cannot effectively clean the DPF of soot. The engine-cooling-fan switch has 2 positions for controlling the operation of the fan. The 2 positions are R and AUTO. The fan has the ability to reverse to blow debris off the rear screen. Under normal operating conditions, the switch should be in the AUTO position.
Changing Mowing Patterns Change mowing patterns often to minimize after-cut appearance issues induced by repetitive operation in only 1 direction. Adjusting the Counterbalance The counterbalance system maintains hydraulic back pressure on the deck lift cylinders. This counterbalance pressure transfers cutting deck weight to the mower's drive wheels to improve traction.
After Operation displacement hydraulic pump and pushing or towing the machine. After Operation Safety Important: Do not push or tow the machine faster than 3 to 4.8 km/h (2 to 3 mph) because internal transmission damage may occur. The bypass valve must be open whenever you push or tow the machine. General Safety • Clean grass and debris from the cutting units, • • • • drives, mufflers, and engine to help prevent fires. Clean up oil or fuel spills.
Hauling the Machine • Use care when loading or unloading the machine into a trailer or a truck. • Use full-width ramps for loading the machine into a trailer or a truck. • Tie the machine down securely using straps, chains, cable, or ropes. Both front and rear straps should be directed down and outward from the machine.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Note: Download a free copy of the electrical or hydraulic schematic by visiting www.Toro.com and searching for your machine from the Manuals link on the home page. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Torque the wheel nuts. After the first 200 hours Before each use or daily • Change the planetary gear drive oil.
Maintenance Service Interval Maintenance Procedure • • • • • Before storage Drain and clean the fuel tank. Check the tire pressure. Check all fasteners. Grease or oil all grease fittings and pivot points. Paint chipped surfaces. • Inspect the fuel lines and connections. Yearly Important: Refer to your Engine Operator's Manual and Cutting Unit Operator's Manual for additional maintenance procedures. Daily Maintenance Checklist Duplicate this page for routine use.
Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Sat. Sun. Lubricate all grease fittings.2 Check the height-of-cut adjustment. Touch-up damaged paint. 1. Check the glow plug and injector nozzles if hard starting, excess smoke, or rough running is noted. 2. Immediately after every washing, regardless of the interval listed.
Lubrication Pre-Maintenance Procedures Greasing the Bearings and Bushings Removing the Hood Service Interval: Every 50 hours (or after every washing). 1. Release the hood latches (Figure 45) and pivot open the hood. The machine has grease fittings that must be lubricated regularly with No. 2 lithium grease. The grease fitting locations and quantities are as follows: • Brake-shaft pivot bearings (5) (Figure 46) g009984 g009704 Figure 45 Figure 46 1.
• Steering cylinder ball joints (2) (Figure 48) • Cutting unit spindle-shaft bearings (2 per cutting unit) (Figure 50) Note: You can use either fitting, whichever is more accessible. Pump grease into the fitting until a small amount appears at bottom of the spindle housing (under the deck). g009708 g009706 Figure 50 Figure 48 1.
Engine Maintenance Engine Safety Shut off the engine before checking the oil or adding oil to the crankcase. g031879 Servicing the Air Cleaner Service Interval: Every 400 hours Check the air-cleaner body for damage that could cause an air leak. Replace it if it is damaged. Check the whole intake system for leaks, damage, or loose hose clamps. Service the air-cleaner filter only when the service indicator (Figure 52) requires it.
Servicing the Engine Oil Oil Specification Use high-quality, low-ash engine oil that meets or exceeds the following specifications: • API service category CJ-4 or higher • ACEA service category E6 g031871 • JASO service category DH-2 Important: Using engine oil other than API CJ-4 or higher, ACEA E6, or JASO DH-2 may cause the diesel particulate filter to plug or cause engine damage.
Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter Service Interval: Every 6,000 hours or clean the soot filter if engine faults SPN 3720 FMI 16, SPN 3720 FMI 0, or SPN 3720 FMI 16 display in the InfoCenter. • If advisory message ADVISORY 179 displays in the InfoCenter, the DPF is nearing the recommended point for servicing the diesel-oxidation catalyst and the soot filter.
Servicing the Water Separator Fuel System Maintenance Service Interval: Before each use or daily—Drain water or other contaminants from the fuel filter/water separator. DANGER Under certain conditions, diesel fuel and fuel vapors are highly flammable and explosive. A fire or explosion from fuel can burn you and others and can cause property damage. Every 400 hours—Replace the fuel-filter canister. • Use a funnel to fill the fuel tank outdoors, in an open area, when the engine is off and is cold.
Servicing the Fuel Filter Electrical System Maintenance Service Interval: Every 400 hours 1. Clean the area around the fuel filter head (Figure 59). Charging and Connecting the Battery WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. g028799 1. Unlatch and raise the operator's console panel (Figure 60). Figure 59 1.
DANGER Battery electrolyte contains sulfuric acid which is a deadly poison and causes severe burns. • Do not drink electrolyte and avoid contact with skin, eyes, or clothing. Wear safety glasses to shield your eyes and rubber gloves to protect your hands. • Fill the battery where clean water is always available for flushing the skin. 2. Connect a 3 to 4 A battery charger to the battery posts. Charge the battery at a rate of 3 to 4 A for 4 to 8 hours. g009986 Figure 61 3.
WARNING Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Always connect the positive (red) battery cable before connecting the negative (black) cable. Servicing the Battery Service Interval: Every 50 hours—Check the battery condition. g009985 Figure 63 1.
Checking the Planetary Gear Drive Oil Drive System Maintenance Service Interval: Every 400 hours Checking for End-Play in the Planetary Drives Use high quality SAE 85W-140 wt. gear lube as a replacement. 1. With machine on level surface, position the wheel so one check plug (Figure 66) is at the 12 o'clock position and the other is at 3 o'clock position. Service Interval: Every 400 hours There should be no end-play in the planetary drives/drive wheels (i.e.
Checking the Rear Axle Lubricant Service Interval: Every 400 hours The rear axle is shipped from the factory filled with SAE 85W-140 wt. gear lube. The capacity is 2.4 L (80 oz). Visually inspect for leaks daily. 1. Position the machine on a level surface. 2. Remove a check plug from 1 end of the axle (Figure 69) and make sure that the lubricant is up to the bottom of the hole. 3.
3. Remove the 3 oil-level check plugs and main axle vent cap to ease in draining of the oil. The front measurement must be 3 mm (1/8 inch) less than the rear measurement (Figure 72). 4. Remove the drain plugs and allow the oil to drain into the pans. 5. Install the plugs. 6. Remove a check plug and fill axle with approximately 2.4 L (80 oz) of 85W-140 gear lube or until lubricant is up to bottom of hole. 7. Install the check plug. Checking the Rear Axle Gear Box Lubricant g009169 Figure 72 1.
Cooling System Maintenance Cooling System Safety CAUTION Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. • Do not remove the radiator cap when the engine is hot. Always allow the engine to cool at least 15 minutes or until the radiator cap is cool enough to touch without burning your hand before removing the radiator cap. g009702 Figure 74 • Do not touch the radiator and surrounding parts that are hot. 1. Expansion tank 2.
4. Close the rear screen and secure it with the latch. g009988 Figure 75 1. Rear-screen latch 3. Thoroughly clean both sides of the oil cooler and the radiator (Figure 76) with compressed air. Start from the front and blow the debris out toward the back. Then clean from the back side and blow toward the front. Repeat procedure several times until you remove all chaff and debris. g020509 Figure 76 1.
Brake Maintenance Belt Maintenance Adjusting the Service Brakes Servicing the Alternator Belt Adjust the service brakes when there is more than 25 mm (1 inch) of free travel of the brake pedal or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before braking resistance is felt. Service Interval: Every 100 hours 1. Check the tension of the alternator belt by depressing it midway between the alternator and the crankshaft pulleys with 4.5 kg (10 lb) of force.
Hydraulic System Maintenance High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 Material Properties: Viscosity, ASTM D445 Hydraulic System Safety Viscosity Index ASTM D2270 Pour Point, ASTM D97 WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury. Industry Specifications: • Ensure that all hydraulic-fluid hoses and lines are in good condition and all hydraulic connections and fittings are tight before applying pressure to the hydraulic system.
2. Disconnect the case return line from the bottom of the reservoir and let the hydraulic fluid flow into a large drain pan. 3. Install the hose when the hydraulic fluid stops draining. 4. Fill the reservoir with approximately 28.4 L (7.50 US gallons) of hydraulic fluid; refer to Checking the Hydraulic-Fluid Level (page 59). g031878 Important: Use only the hydraulic fluids specified. Other fluids could cause system damage. 5. Install the reservoir cap. 6.
Replacing the Hydraulic Filters Checking the Hydraulic Lines and Hoses Service Interval: After the first 200 hours Service Interval: Before each use or daily Every 800 hours Inspect the hydraulic lines and hoses for leaks, kinked lines, loose mounting supports, wear, loose fittings, weather deterioration, and chemical deterioration. Make all necessary repairs before operating the machine. Use Toro replacement filters Part No. 94-2621 for the rear (cutting unit) of the machine and Part No.
Mounting the Cutting Decks to the Traction Unit Cutting Deck Maintenance 1. Position the machine on a level surface and turn the key in the ignition switch to the OFF position. 2. Move cutting deck into position in front of traction unit. 3. Slide deck carrier frame onto lift-arm pivot pin. Secure with lynch pin or retaining nut (Groundsmaster 4700 only) (Figure 82). 4. Install the hydraulic motor to the deck (Figure 81). Make sure that the O-ring is in position and not damaged. 5. Grease the spindle.
5. Rotate the marked end of the blade to the 3 and 9 o’clock positions (Figure 83) and measure the heights. 6. Compare the 12 o’clock measured height to the height-of-cut setting. It should be within 0.7 mm (0.030 inch). The 3 and 9 o’clock heights should be 3.8 ± 2.2 mm (0.150 ± 0.090 inch) higher than the 12 o’clock setting and within 2.2 mm (0.090 inch) of each other. height then no adjustment is needed for that side. Adjust the other side to within ± 2.2 mm (0.090 inch) of the correct side. 7.
Inspecting and Sharpening the Blade DANGER A worn or damaged blade can break, and a piece of the blade could be thrown into the operator’s or bystander’s area, resulting in serious personal injury or death 1. Raise the cutting deck to the highest position, turn the key in the ignition switch to the OFF position, and engage the parking brake. 2. Block the cutting deck to prevent it from falling accidentally. • Inspect the blade periodically for wear or damage. 3.
Note: This blade will produce good quality of cut and require minimal power from the engine. By contrast, a blade that is higher at the ends than the center, or if cutting edge is higher than the heel, the blade is bent or warped and must be replaced. outer race until the inner race comes in contact with the spacer. 4. Install the roller assembly into the deck frame. 5. Verify that there is no more than a 1.5 mm (0.060 inch) gap between roller assembly and the roller mount brackets of the deck frame.
Storage anti-freeze as needed for the expected minimum temperature in your area. Preparing the Traction Unit Cutting Deck 1. Thoroughly clean the traction unit, cutting units, and the engine. If the cutting deck is separated from the traction unit for any length of time, install a spindle plug in the top of the spindle to protect the spindle from dust and water. 2. Check the tire pressure; refer to Checking the Tire Pressure (page 23). 3.
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
