Installation Instructions

ManualsBrandsToro ManualsAttachmentsWinter Attachment Joystick Kit, Groundsmaster 360 Multi-Purpose Machine

FormNo.3408-175RevA

WinterAttachmentJoystickKit

Groundsmaster

360Multi-PurposeMachine

ModelNo.31219

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedormissing.

121–5356

1.Joystick

forward—lower

theattachment

4.Joystick

left—actuate

theattachment

intherst

direction

7.Readthe

Operator's

Manual.

2.Joystick

right—actuate

theattachment

inthesecond

direction

5.Lefttoggle

3.Joystick

rearward—raise

theattachment

6.Righttoggle

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3408-175*A

Summary of content (8 pages)

PAGE 1
Form No. 3408-175 Rev A Winter Attachment Joystick Kit Groundsmaster® 360 Multi-Purpose Machine Model No. 31219 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Qty. Use No parts required – Prepare the machine. Joystick wire harness 1 Route the joystick wire harness. Joystick pod mounting bracket Carriage bolt Clip Joystick Clip Joystick pod cover Joystick pod Hex-head screw (1/4 x 5/8 inch) Knob Decal 1 2 1 1 2 1 1 2 1 1 No parts required – Connect the battery. No parts required – Download the software.
PAGE 3
1 2 Preparing the Machine Routing the Joystick Wire Harness No Parts Required Parts needed for this procedure: Procedure 1 Joystick wire harness 1. Park the machine on a level surface, and lower the mower deck and any attachments to the ground. Procedure 2. Shut off the engine, engage the parking brake, and remove the key from the ignition switch. 1. Plug the joystick wire harness into the joystick expansion port connectors on the main kit wire harness, which are located near the controller. 3.
PAGE 4
3 4 Installing the Joystick Pod Mounting Bracket Installing the Joystick Parts needed for this procedure: Parts needed for this procedure: 1 Joystick 1 Joystick pod mounting bracket 2 Clip 2 Carriage bolt 1 Joystick pod cover 1 Clip 1 Joystick pod 2 Hex-head screw (1/4 x 5/8 inch) 1 Knob 1 Decal Procedure 1. Attach the clip to the front hole in the joystick pod mounting bracket (Figure 3). Procedure 2.
PAGE 5
Connecting the Battery No Parts Required Procedure Connect the negative (–) battery cable to the battery. Note: When the kit is properly installed, the power point and fuse block should have power only when the ignition switch is in the ON position. 6 Downloading the Software No Parts Required Procedure Important: This step must be performed by a Toro Commercial Products Distributor Service staff person.
PAGE 6
Operation 1 5 6 2 4 7 3 G017857 Figure 5 1. Joystick forward 5. Toggle left 2. Joystick right 6. Toggle right 3. Joystick back 7. Joystick 4.
PAGE 7
Operating the V-Plow Refer to Figure 5 while reading the table below. Note: To toggle off, remove your thumb from the toggle switch.
PAGE 8