Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSlope Sensor Kit, Groundsmaster 7200 or 7210 Series Traction Unit

FormNo.3435-476RevA

SlopeSensorKit

Groundsmaster

7200or7210SeriesTractionUnit

ModelNo.31251

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal140-2710

140-2710

1.Warning—readtheOperator’sManual;afastashinglight

andalarmsoundingindicatesasteepslope;aslowashing

lightindicatesamoderateslope;nolightindicatesnormal

operatingconditions.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3435-476*A

Summary of content (8 pages)

PAGE 1
Form No. 3435-476 Rev A Slope Sensor Kit Groundsmaster® 7200 or 7210 Series Traction Unit Model No. 31251 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal140-2710 140-2710 1.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine. Sensor module LED light Bolt (1/4 x 1-1/4 inch) Flange nut (1/4 inch) Bolt (1/4 x 3/4 inch) Mounting bracket Wire harness Alarm Decal Cable tie 1 1 2 4 2 1 1 1 1 2 Install the kit. Decal 1 Install the decal. No parts required – Calibrate the sensor.
PAGE 3
g320860 Figure 1 1. 5 cm (2 inches) 2. Mounting bracket 3. Drill 9/32 inch diameter holes. 4. Check here for existing holes. 3 4. Using the mounting bracket as a template, mark the location of the hole to drill (Figure 1). 5. Drill 9/32 inch holes into the machine frame (Figure 1). 6. Install the mounting bracket to the machine frame with 2 bolts (1/4 x 3/4 inch) and 2 flange nuts (1/4 inch).
PAGE 4
g321005 Figure 4 g320859 Figure 2 1. Flange nut (1/4 inch) 1. 90° connector 3. Bolt (1/4 x 3/4 inch) 2. Mounting bracket 9. 10. 7. Mount the sensor to the mounting bracket with 2 bolts (1/4 x 1-1/4 inch) and 2 nuts (1/4 inch). Flip the seat forward. Remove the access panel behind the seat and on the side of the console (Figure 5). g320856 Figure 3 1. Bolt (1/4 x 1-1/4 inch) g320861 Figure 5 3. Sensor 2. Flange nut (1/4 inch) 11. 8.
PAGE 5
Routing the Wire Harness 1. Route the wire harness under the seat pan and along the along the existing wire harness in the cross channel (Figure 8). 2. Install the middle connector to the machine wire harness connector labeled TELEMATICS port or EXPANSION port (Figure 8). 3. Connect the wire harness to the light and the alarm (Figure 8). Route the harness to the controls along the machine’s existing wire harness. g320855 Figure 6 1. Alarm 3. Threaded ring 2.
PAGE 6
Note: Ensure the harnesses are secured away from moving parts and hot surfaces. 5. Connect the battery. Refer to the Operator’s Manual for the procedure. Installing the Decal Install the decal on the machine as shown in Figure 9. g321003 g321004 Figure 10 g320857 Figure 9 1. Calibration connectors 2. Plug 1. Decal 3. Calibrating the Sensor 1. While on a flat surface, remove the plug from the calibration connectors (Figure 10). 2. Plug the calibration connectors together as shown in Figure 10.
PAGE 7
4. Use the following processes depending what LED light your machine has installed. A. Console LED light (Figure 11): i. The LED light (Figure 11) blinks as the sensor calibrates. ii. When the LED light turns off and the sensor beeps once, the sensor is calibrated. iii. Turn the ignition key to the OFF position. g321268 Figure 12 1. InfoCenter LED light 5. Disconnect the calibration connectors and install the plug onto the connectors (Figure 13). g321269 Figure 11 1. LED light B.
PAGE 8
Operation Use the following procedures depending what your machine has installed. WARNING g317558 Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. Figure 15 Advisory 197 Use extreme caution when operating the machine on a slope.