Installation Instructions

ManualsBrandsToro ManualsRiding ProductsWindshield Wiper Kit, Groundsmaster or Reelmaster Series Traction Unit with 2 Post ROPS Extension Kit

FormNo.3406-253RevA

WindshieldWiperKit

Groundsmaster

orReelmaster

SeriesTractionUnitwith2Post

ROPSExtensionKit

ModelNo.31311

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Wipermotor1

Wiperarm1

Wiperblade1

Installthewipermotor.

Wiperarm1

Wiperblade1

Installthewiperarm.

Reservoir1

Bracket1

Bolt(5/16x3/4inch)

Flangenut(5/16inch)

Hose1

Hosebarb1

Cabletie

Installthereservoir.

Switch

1Installtheswitch.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-253*A

Summary of content (8 pages)

PAGE 1
Form No. 3406-253 Rev A Windshield Wiper Kit Groundsmaster® or Reelmaster® Series Traction Unit with 2 Post ROPS Extension Kit Model No. 31311 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 1 Installing the Wiper Motor 7 8 Parts needed for this procedure: 1 Wiper motor 1 Wiper arm 1 Wiper blade g035739 6 Procedure 5 4 3 2 Figure 2 1. Park the machine on a level surface, shut off the engine, engage the parking brake, and remove the key from the ignition switch. 1. Motor 2. Gasket 5. Bolt 6. Plastic cap 3. Shaft assembly 7. Jam nut 2. Remove the bolt and lock washer from the shaft assembly (Figure 2). 4. Lock washer 8. Washer 3.
PAGE 3
1 2 1 g03551 1 2 Figure 3 1. Large locknut 2. Wiper arm g035513 Figure 5 1. Screws 2. Wiper blade 5. Install the hose onto the wiper arm barb. 6. Adjust the washer-spray tips toward the front glass for proper washer spray. 3 Installing the Reservoir 1 g035512 Parts needed for this procedure: Figure 4 1. 76 mm (3 inches) 4. Install the wiper blade as shown in Figure 5.
PAGE 4
1 2 1 3 g035758 Figure 6 1. Bolt (5/16 x 3/4 inch) 3. Flange nut (5/16 inch) Figure 8 2. Bracket 3. Hose 1. Cover 2. Harness connector 2. Install the tank to the bracket with 4 bolts (5/16 x 3/4 inch) and 4 flange nuts (5/16 inch) as shown in Figure 7. 1 Figure 7 1. Bracket installed 2. Flange nut (5/16 inch) g035633 Figure 9 3. Reservoir 4. Bolt (5/16 x 3/4 inch) 1. Reservoir installed 3. Remove the cover from the post (Figure 8). 6. Trim the hose to length. 4.
PAGE 5
4 Installing the Switch Parts needed for this procedure: 1 Procedure Figure 10 1. Cable tie 2. Hose Switch 1. Remove the existing plug in the control panel. 3. Hose barb 2. Locate the plug in the existing wire harness and connect the switch to the plug (Figure 12). 1 g035509 Figure 12 1. Switch Figure 11 1. Cable tie 2. Hose 3. Hose barb 8. Secure the hose to the wire harness with the cable ties as shown in Figure 11. 9. Install the cover to the post (Figure 8).
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8