Form No. 3416-616 Rev A 2 Post ROPS Extension Kit Groundsmaster® 4500, 4700 or Reelmaster® 7000 Series Traction Unit Model No. 31351—Serial No. 400000000 and Up Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Installation 1 Preparing the Machine No Parts Required g204217 Procedure Figure 2 Foot frame 1. Park the machine on a level surface. 2. Lower the cutting units. 3. Engage the parking brake. 4. Shut off the engine and remove the key. 5. If there are lights on the roll bar, remove the lights and the mounting hardware from the roll bar. Retain the lights and the mounting hardware. 6. Remove the locking pins from both sides of the roll bar (Figure 1). g204504 Figure 3 Left side shown 1.
2 1. Install 2 bolts (3/4 x 4 inches), 4 washers, and 2 locknuts (3/4 inch) to the left and right pivot plates on the roll bar. 2. Install the left and right front mount bases onto the floor panel using 4 bolts (3/8 x 1 inch) and 4 flange nuts (3/8 inch). 3. Install the rear roof mount onto the upper part of the roll bar with 2 roof channel mounts, 8 carriage bolts (5/16 x 3/4 inch), and 8 flange nuts (5/16 inch).
13. Install 3 push rivets into the left brace and 5 push rivets into the right brace. 14. Install the grab handle to the left brace with 2 carriage bolts (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch). 15. Install the lower window seal to the front mounts with 4 carriage bolts (1/4 x 3/4 inch) and 4 flange nuts (1/4 inch). 16. Install the upper left and lower left post covers onto the left brace with 7 plastic rivets. 17.
g219683 Figure 5 1. Roll bar 11. Hex-head-flange bolt (5/16 x 1 inch) 21. Plastic rivet 31. Bolt (3/4 x 4 inches) 2. Left front mount 12. Front roof mount 22. Plastic plug 32. Washer 33. Locknut (3/4 inch) 3. Right front mount 13. Left upper bracket 23. Panel plug 4. Right brace 14. Right upper bracket 24. Upper left post cover 34. Side channel mount 5. Left brace 15. Rear roof mount 25. Lower left post cover 35. Roof channel mount 6. Carriage bolt (5/16 x 3/4 inch) 16.
2. 3 Open the hood (Figure 7). Installing the Wire Harness Groundsmaster 4700 Machine Only Parts needed for this procedure: 1 Wire harness 4 Cable tie Procedure 1. Unlatch and raise the battery box cover (Figure 6). g036674 Figure 7 3. Route the wire harness as shown in Figure 8. Use the cable ties to secure the wire harness to machine; refer to Figure 8 Note: Route the wire harness through the bottom of the battery box and under the machine frame. g009985 Figure 6 1. Battery box cover 2.
g203834 Figure 8 1. Cable ties 4. Close the hood and the battery box cover. Note: Secure the battery box cover closed with the latch.
4 Installing the Control Panel and Sunshade 4. Secure the front panel onto the front roof mount by inserting 12 plastic rivets into their respective holes and pushing the plunger on each plastic rivet until it is secure (Figure 9). 5. Install the sunshade onto the frame with 4 hex-head flange bolts (1/4 x 1 inch), 4 sealing washers, and 4 clips (Figure 10).
Notes:
Notes:
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
