Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSecurity Cage Kit, Groundsmaster 5900 Traction Unit with 2 Post ROPS Extension

FormNo.3422-843RevB

SecurityCageKit

Groundsmaster

5900TractionUnitwith2PostROPSExtension

ModelNo.31354

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Thiskitts2PostROPSExtensionKitModel31353only.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethestoragecompartment.

Right,rearpanel1

Left,rearpanel

Flangelocknut(5/16inch)

Carriagebolt(5/16x3/4inch)

Screw(10-24x5/8inch)

Latchcatch2

Flangelocknut(10-24)

Assembletherear,transition,andcenterpanels.

Nopartsrequired

–

Installthestoragecompartment.

Leftsidepanel

Rightsidepanel1

Mountbracket2

Carriagebolt(5/16x3/4inch)

Flangelocknut(5/16inch)

Leftdoormount

Rightdoormount1

Installtheleftandrightsidepanelsanddoormounts.

Rubberlatch2

Rearscreenassembly1

Carriagebolt(10-24x5/8inch)

Flangelocknut(10-24)

Lefthinge

Righthinge1

Carriagebolt(5/16x3/4inch)

Flangelocknut(5/16inch)

Brassspacer2

Hingehalf

Shoulderbolt(5/16x1-1/4inches)

Flangebushing(neoprene—0.31inch)

Backerplate2

Flangebushing(neoprene—0.56inch)

Installtherearscreen.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3422-843*B

Summary of content (12 pages)

PAGE 1
Form No. 3422-843 Rev B Security Cage Kit Groundsmaster® 5900 Traction Unit with 2 Post ROPS Extension Model No. 31354 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. This kit fits 2 Post ROPS Extension Kit Model 31353 only. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the storage compartment.
PAGE 2
Description Use Qty. Spacer (brass) Left door Right door Door dampener bracket Carriage bolts (5/16 x 3/4 inch) Flange locknut (5/16 inch) Door dampener (spring-gas) Ball stud Jam nut Pin guard Latch-pin cam Thrust washer Latch pin 4 1 1 2 16 20 2 2 2 2 2 4 2 No parts required – Adjust the door-latch pins. Dual-tab mount Side-tab mount Top-tab mount Rivet Lower-windshield assembly Upper-windshield assembly Socket-head screw (5/16 x 1-1/2 inches) Backup washer Flange bushing (neoprene—0.
PAGE 3
2. Remove the 2 socket-head screws, 4 washers, and 2 nuts that secure the storage compartment to the side panel (Figure 1). Note: Use a shortened hex key to remove the socket-head screws. 3. Remove the 2 push-in fasteners and 2 washers that secure the storage compartment to the side panel (Figure 2). g253784 Figure 2 1. Push-in fasteners 4. 2. Washers Remove the storage compartment from the machine (Figure 3).
PAGE 4
Assembling the Rear, Transition, and Center Panels g254011 Figure 4 1. Platform of the machine 5. Carriage bolt (5/16 x 3/4 inch) 2. Right, rear panel 6. Right transition panel 3. Left, rear panel 7. Left transition panel 4. Flange locknut (5/16 inch) 8. Screw (10-24 x 5/8 inch) 9. Latch catch 10. Flange locknut (10-24) 1. Assemble the left and right, rear panels to the back of the platform of the machine (Figure 4) with 4 carriage bolts (5/16 x 3/4 inch) and 4 flange locknuts (5/16 inch). 2.
PAGE 5
Installing the Storage Compartment 1. Align the holes in the storage compartment with the holes in the side panel (Figure 5). g253786 Figure 7 1. Nut 2. Washer 4. Socket-head screw 5. Side panel 3. Storage compartment 4. g253989 Figure 5 2. Assemble the storage compartment to the side panel with the 2 push-in fasteners and 2 washers (Figure 6). g253784 Figure 6 1. Push-in fasteners 3. 2.
PAGE 6
Installing the Left and Right Side Panels and Door Mounts g254022 Figure 8 1. ROPS tube 4. Right side panel 7. Mount bracket 2. Upper ROPS bracket mount 5. Carriage bolt (5/16 x 3/4 inch) 8. Left door mount 3. Left side panel 6. Flange locknuts (5/16 inch) 9. Right door mount 1. Assemble the left and right side panels to the upper ROPS bracket mount (Figure 8) with 4 carriage bolts (5/16 x 3/4 inch) and 4 flange locknuts (5/16 inch).
PAGE 7
Installing the Rear Screen g254023 Figure 9 1. Rubber latch 6. Right hinge 11. Shoulder bolt (5/16 x 1-1/4 inches) 2. Rear screen assembly 7. Upper ROPS bracket mount 12. Flange bushing (neoprene—0.31 inch) 3. Screw (10-24 x 5/8 inch) 8. Bolt (5/16 x 3/4 inch) 13. Flange bushing (neoprene—0.56 inch) 4. Nuts (10-24) 9. Nut (5/16 inch) 14. Backer plate 5. Left hinge 1. 2. 3. 10. Hinge half 15.
PAGE 8
Installing the Doors Assembling the Doors to the Machine g254025 Figure 10 1. Left door hinge 3. Right door hinge 2. Spacer (brass) 4. Left door 1. Assemble a brass spacer onto each of the hinge pins of the door mounts (Figure 10). 2. Assemble the door onto the door mount (Figure 10). 3. Repeat steps 1 and 2 for the door at the other side of the machine. 8 5.
PAGE 9
Installing the Door Dampener Brackets Installing the Door Dampeners Installing the Door Dampener Brackets 1. Align the holes in the door dampener bracket with the holes in the upper bracket of the 2 post ROPS (Figure 11). g254038 g254026 Figure 11 1. Door dampener bracket 3. Flange locknut (5/16 inch) 2. Carriage bolts (5/16 x 3/4 inch) 4. Upper bracket (2 post ROPS) 2.
PAGE 10
3. Assemble the cylinder end of the door dampener (spring-gas) onto the ball stud on the upper-hinge bracket of the door (Figure 12). 4. Assemble the rod end of the door dampener onto the ball stud door dampener bracket on the upper bracket of the 2 post ROPS (Figure 12). 5. Repeat steps 1 through 4 for the door at the other side of the machine. Adjusting the Door-Latch Pins 1. Center the latch pin in the latch-pin-mount bracket on the rail (Figure 14). Assembling the Door Latch 1.
PAGE 11
g036321 Figure 15 1. Bubble seal 3. 1.9 to 2.2 cm (3/4 to 7/8 inch) 2. Cab rail 4. Tighten the jam nut once the latch pin reaches 1.9 to 2.2 cm (3/4 to 7/8 inch) as shown in Figure 14.
PAGE 12
Installing the Windshield g036172 Figure 16 1. Dual-tab mount 5. Lower windshield assembly 9. Flange bushing (neoprene—0.31 inch) 2. Side-tab mount 6. Upper windshield assembly 10. Flange bushing (neoprene—0.56 inch) 3. Top-tab mount 7. Socket-head screw (5/16 x 1-1/2 inches) 11. Flange locknut (5/16 inch) 4. Rivet 8. Backup washer 1. Install the dual-tab mount between the upper and lower windshield frame on the ROPS (Figure 16). 2.