Installation Instructions

ManualsBrandsToro ManualsAttachmentsBeacon Kit, 2015 and After Groundsmaster Series Traction Unit

FormNo.3389-322RevC

BeaconKit

2015andAfterGroundsmaster

SeriesTractionUnit

ModelNo.31509

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal130-5986

130–5986

1.On3.Off

2.Beacon

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3389-322*C

Summary of content (8 pages)

PAGE 1
Form No. 3389-322 Rev C Beacon Kit 2015 and After Groundsmaster® Series Traction Unit Model No. 31509 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal130-5986 130–5986 1. On 2. Beacon © 2020—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 3. Off Register at www.Toro.com.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description No parts required – Prepare the machine and disconnect the battery. No parts required – Remove the roof. 3 Beacon switch Beacon decal Beacon mount Carriage bolt (3/8 x 7/8 inch) Flange nut (3/8 inch) 1 1 1 2 2 Install the beacon switch and mount. 4 No parts required – Route the wire harness. 5 Beacon socket Beacon Spacer Carriage bolt (3/8 x 1 inch) 1 1 1 2 Install the beacon.
PAGE 3
2 Removing the Roof No Parts Required Procedure g313347 Figure 2 Remove the roof from the cab by removing the 22 screws securing it to the cab (Figure 1). 1. Beacon decal 2. 2. Beacon switch Secure the beacon mount to the machine with 2 carriage bolts (3/8 x 7/8 inch) and 2 flange nuts (7/8 inch) as shown in Figure 3. g032048 Figure 1 1. Bolt 2. Roof 3. Nutz 3 Installing the Beacon Switch and Mount g036669 Figure 3 1.
PAGE 4
Routing the Wire Harness No Parts Required Procedure 1. GM5910 cabs only: Remove the existing bracket and install the beacon mount (Figure 4). Note: Install the existing bracket back onto the cab over the beacon bracket. g028878 Figure 5 1. 10.31 mm (0.406 inch) hole 4. Locate the 2 spade connectors in the roof of the cab and route them through the previously drilled hole (Figure 6). g028879 Figure 4 1. Carriage bolt (3/8 x 1 inch) 4. Nut 2. Washer 3. Existing bracket 5. Beacon mount 2.
PAGE 5
Installing the Beacon Parts needed for this procedure: 1 Beacon socket 1 Beacon 1 Spacer 2 Carriage bolt (3/8 x 1 inch) Procedure 1. 2. 3. Remove the beacon connector from the beacon socket (Figure 7). g036673 Figure 7 Route the wire harness up through the jam nut, washer, beacon socket, and connect it to the beacon connector (Figure 7). Plug the spade connectors on the wire harness into the beacon connector. 1. Beacon light 4. Lock washer 2. Beacon connector 3. Beacon socket 5.
PAGE 6
Operation Controls Beacon Switch Press the beacon switch to the On position to activate the beacon.
PAGE 7
Notes:
PAGE 8