Installation Instructions

ManualsBrandsToro ManualsAttachmentsROPS Beacon Kit, Groundsmaster 4500-D, 4700-D or Reelmaster 7000-D Traction Unit

FormNo.3403-711RevA

ROPSBeaconKit

Groundsmaster

4500-D,4700-DorReelmaster

7000-DTraction

Unit

ModelNo.31577

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Beaconbracket1

U-bolt1

Beaconsocket1

Beaconassembly1

Nut2

Installthebeaconassembly.

Wireharness1

Cabletie

Mountingpad3

Installthewireharness.

Fuse1

Switch

Cabletie

Installthefuseandswitch(formachineswithouttheCE

LightKit).

MediaandAdditionalParts

Description

Qty.

Use

Installationinstructions1

Readinstructionsbeforeinstallingandoperatingthekit

Partscatalog1

Usetoreferencepartnumbers

PreparingtheMachine

1.Parkthemachineonalevelsurface,engagetheparking

brake,andremovethekeyfromtheignition.

2.Openthehood.

3.Disconnectthenegativebatterycablefromthebattery.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3403-711*A

Summary of content (4 pages)

PAGE 1
Form No. 3403-711 Rev A ROPS Beacon Kit Groundsmaster® 4500-D, 4700-D or Reelmaster® 7000-D Traction Unit Model No. 31577 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
Installing the Beacon Assembly Installing the Wire Harness 1. Plug the wire harness into the beacon assembly. 2. Affix the 3 mounting pads to the ROPS post, route the wire harness down the post, and secure the wire harness to the pads with 3 cable ties. 1. Loosely secure the beacon-light bracket to the side of the ROPS post with the U-bolt and nuts as shown in Figure 1. 1 2 G023204 Figure 3 1. Cable tie 2. Mounting pad 3.
PAGE 3
Installing the Fuse and Switch 4. Route the fuse-connector section of the wire harness through the opening of the fuse compartment. For Machines without the CE Light Kit 5. Connect the ring terminal from the wire harness to 1 of the bolts on the ground-block terminal (Figure 6). 1. Secure the wire harness to the hydraulic tube using a cable tie (Figure 4). Figure 6 1. Ring terminal 2. Fuse in connector 6. Install the fuse to the fuse connector (Figure 6). 7.
PAGE 4
Operation Operating the Beacon Switch Press the beacon switch to activate the beacon (Figure 9). Figure 8 1. Knockout 2. Switch 11. Plug the wire harness into the switch. 12. Install the side panel (Figure 7). 13. Install the fuse-compartment clamp and seal to the machine with the bolt that you removed in step 2. 14. Install the negative (-) cable to the battery. 15. Close the hood. Figure 9 Machines with the CE Light Kit 1. Turn signal switch 3. Hazard switch 2. Horn button 4.