Installation Instructions

ManualsBrandsToro ManualsAttachmentsLED Work Light Kit, 2015 and After Cab and 2 Post ROPS Extension Kit

FormNo.3402-104RevB

LEDWorkLightKit

2015andAfter—Caband2PostROPSExtensionKit

ModelNo.31596

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachinebeforeinstallation.

Lightassembly4

Leftmount(2postROPSextension)

Rightmount(2postROPSextension)

Rearmount(2postROPSextension)

Cabmount

Carriagebolt(5/16x3/4inch)

Flangenut(5/16)

Bolt(1/4x7/8inch)

Flangenut(1/4inch)

Bolt(6mmx20mm)

Wireharnesswithgrommet(cab)

Switch

Switchdecal(2postROPSextension)

Installthelights.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3402-104*B

Summary of content (8 pages)

PAGE 1
Form No. 3402-104 Rev B LED Work Light Kit 2015 and After—Cab and 2 Post ROPS Extension Kit Model No. 31596 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Prepare the machine before installation.
PAGE 2
Installing the Light kit to the Cab 1 1. Remove the bolts and nuts that secure the top of the headliner and set them aside (Figure 1). Preparing to Install the Kit No Parts Required Preparing the Machine 1. Move the machine to a maintenance workspace, shut off the machine and remove the key. 2. Disconnect the negative (-) battery cable from the battery; Refer to the machines Operator’s Manual. g032048 Figure 1 1. Bolt 2. Headliner 2 2. Installing the Lights 3.
PAGE 3
. Insert the grommets on the wire harness into the holes that you drilled. 4. Remove the bracket on the light assembly and install the bracket supplied with the kit (Figure 4). g033552 Figure 5 1. Flange nut 3. Bracket 2. Flat washer 4. Shoulder bolt 6. Connect the wire harnesses together (Figure 6). g033551 Figure 4 1. Nut 2. Bracket 5. 3. Bolt 4. Light assembly Use the existing hardware on the headliner to secure the light bracket to the headliner (Figure 5).
PAGE 4
Installing the Light to a 2 Post ROPS Extension Note: Ensure that your machine is equipped with the optional accessory-wire harness installed. Contact your authorized Toro distributor if your machine requires the accessory-wire harness. 1. g033595 Install the light mount to the bracket. • For a machine with mirrors: Use the 4 bolts (6 mm x 20 mm) to secure the light assembly through the bracket and to the mirror mount (Figure 9). Figure 7 1. Wire-harness connector 8.
PAGE 5
2. Remove the carriage bolt, washer and nut from the light assembly and use them to secure the light to the bracket (Figure 11). g033550 Figure 12 1. Wire harness 4. Use the carriage bolt (5/16 x 3/4 inch) and flange nuts to secure the light assembly to the frame (Figure 13). g033544 Figure 11 1. Carriage bolt 4. Washer 2. Light assembly 5. Nut 3. Bracket g033742 3. Figure 13 Connect the wire harness to the to the light assembly (Figure 12). 1. Nut (5/16) 3.
PAGE 6
g033598 Figure 16 1. Decal 8. Apply the decal to the panel as shown in Figure 16. 9. Connect the accessory-wire harness to the switch assembly. g033547 Figure 14 1. Carriage bolt 4. Washer 2. Bracket 3. Light assembly 5. Nut 6. Connect the wire harness to the to the light assembly and secure it with the wire anchors (Figure 15). 2. Switch assembly 10. Connect the negative (-) battery cable. 11. Turn the lights on. Refer to Operating the Light (page 6). 12.
PAGE 7
Notes:
PAGE 8