Form No. 3399-482 Rev A Groundsmaster® 5900 and 5910 Rotary Mower Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 31598—Serial No. 315000501 and Up 31598TE—Serial No. 315000501 and Up 31599—Serial No. 315000501 and Up 31599TE—Serial No.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
Contents Lubrication ...............................................................40 Greasing the Bearings and Bushings ..........................40 Engine Maintenance ..................................................43 Engine Safety.........................................................43 Air-Cleaner Maintenance .........................................43 Servicing the Engine Oil..........................................44 Adjusting the Valve Clearance ..................................
Safety Cleaning the Air-Conditioning Assembly ........................................................................64 Storage ........................................................................65 Preparing for Seasonal Storage .................................65 This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. General Safety This product is capable of amputating hands and feet and of throwing objects.
Sound Pressure Level Sound pressure level was determined according to the procedures outlined in EN ISO 5395:2013. CAUTION Vibration Level Long-term exposure to noise while operating the machine may cause some hearing loss. Hand-Arm Wear adequate hearing protection whenever you operate the machine for an extended period of time. Measured vibration level for right hand = 0.63 m/s2 Measured vibration level for left hand = 0.65 m/s2 Model 31598 Uncertainty Value (K) = 0.
106-6754 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 114-0133 106-6755 1. Engine coolant under pressure. 3. Warning—do not touch the hot surface. 2. Explosion hazard—read the Operator's Manual. 4. Warning—read the Operator's Manual. 1. Headlights 7. Traction assist—engage 2. On 8. Traction assist—disengage 3. Off 9. Lower cutting units—left 4. Headlight switch location 5. Cruise control—engage 10.
114-0846 1. Read the Operators Manual; to start the engine, move the traction pedal to Neutral, apply the brake, move the throttle switch to low, turn the ignition key to Preheat. When the Wait to Start Advisory clears on the Info Center, turn the ignition key to Start. 2. Read the Operators Manual; to stop the engine, move the throttle lever to slow, disengage the PTO, set the parking brake, wait 5 minutes, turn the ignition key to Stop, and remove the key; read the Operators Manual. 3.
114-0848 1. High range 6. Low idle 2. Transmission 7. Increase engine speed 3. Low range 8. Engine 4. High idle 5. Mid idle 114-0849 1. Warning—disengage the PTO then raise the deck. 2. No step 3. Traction control pedal 9. Read the Operator’s Manual. 10. Decrease engine speed 4. Forward 5. Reverse 114-0864 1.
114-0865 1. Height-of-cut adjustment 114-4883 1. Belt routing 114-9600 1. Read the Operator's Manual. 114-0922 114-0922 1. Belt routing 115-5459 1. Electric shock hazard—do not remove cover; keep cover in place. 114-0974 1. Belt routing 115-5489 (Model 31599 Only) 1. Warning—when the cab windows are open, wear hearing protection. 2. Close the rear window before attempting to open the hood.
115-5509 (Model 31599 Only) 120-6604 1. Thrown object hazard—keep bystanders away from the machine. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts, keep all guards and shields in place. 117-2718 3. Cutting/dismemberment hazard of foot, mower blade—stay away from moving parts, keep all guards and shields in place. 117-4979 1. Entanglement hazard, belt—stay away from moving parts, keep all guards and shields in place. 121-3883 1. Disengage the PTO 2.
Battery Symbols Some or all of these symbols are on your battery 121-3884 1. Engine—stop 3. Engine—start 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3. Caustic liquid/chemical burn hazard 4. Wear eye protection. 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 2. Engine—preheat 5.
114-0975 1. Height of cut 117-2754 1. Warning—read the Operator's Manual. 2. Warning—do not operate this machine unless you are trained. 3. Warning—wear the seat belt when seated in the operator's position. 4. Warning—wear hearing protection. 5. Thrown object hazard—keep bystanders a safe distance from the machine. 6. Cutting hazard of hand or foot—stay away from moving parts; keep all guards in place. 7.
0-2449 1. Read the Operator’s Manual for information on maintenance.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Remove the side-deck shipping straps and brace. 2 Right deck cover Left deck cover V-Belt 1 1 2 Lower the front deck winglets. No parts required – Level the front, center deck. No parts required – Level the winglet decks to the front, center deck. No parts required – Prepare the machine. 3 4 5 Media and Additional Parts Description Use Qty.
2 Lowering the Front-Deck Winglets Parts needed for this procedure: 1 Right deck cover 1 Left deck cover 2 V-Belt Procedure 1. Remove the nuts securing the front and rear stop bolts to the right winglet-deck mounts (Figure 3). Figure 4 1. Winglet 4. Eccentric 2. Hinge pin 5. Lower hole 3. Bolt 5. Install the nuts securing the stop bolts. Note: Do not tighten the nuts at this time. 6. Repeat this procedure on left winglet. 7. Install the winglet belts as follows: A.
8. Install the winglet-deck cover and secure it with the rubber latch (Figure 6). 4 Note: Ensure that you slide the cover under the front, center deck-cover tabs before inserting it onto the mounting hooks and post. Leveling the Winglet Decks to the Front, Center Deck 9. Repeat this procedure on the other winglet. No Parts Required Procedure 1. Rotate the blade on each winglet so that it points side to side. 2. Loosen the bolts and nuts securing the 2 eccentric spacers to the winglets (Figure 7).
Product Overview Controls Note: Determine the left and right sides of the machine from the normal operating position. Figure 8 1. Eccentric notch 4. Tighten the bolt and nut for this eccentric to 149 N·m (110 ft-lb). 5. Adjust the forward eccentric until it just makes contact with the inner slot surface of the winglet-pivot brackets. 6. Tighten the bolt and nut for this eccentric to 149 N·m (110 ft-lb). Figure 9 7. Repeat the procedure on the opposite winglet. 5 1. Brake pedals 7.
Steering-Lever Tilt Press the lever down to tilt the steering wheel to the desired position. Release the lever to lock the adjustment (Figure 9). Turn-Signal Switch Press the left side of the turn-signal switch to activate the left-turn signal and the right side of the switch to activate the right-turn signal (Figure 9). Note: The center position is off. High-Low Range Speed Switch Figure 10 Press the front of the switch to select HIGH-SPEED RANGE. Press the rear of the switch to select LOW -SPEED RANGE.
Cruise-Control Switch Windshield-Wiper Switch The cruise-control switch sets your desired speed of the machine. Use the windshield-wiper switch to turn the windshield wipers to the ON or OFF position (Figure 11). Press the switch forward to engage the cruise control and rearward to disengage it (Figure 10). Power Outlet Audible Alarm (Console) Use this 15 amp, 12 V DC power outlet to power compatible devices (Figure 11). The alarm is activated when a fault is detected.
Power Point Operator Information The power point, located next to the console on the side of the power center, is used to power optional electrical accessories (Figure 10). There are 2 screens that monitor and display the machine functions that you can use. Screen 1 displays the following: Seat-Adjusting Lever • Top, Left Gauge—Engine-Coolant Temperature Pull out the lever to slide the seat forward or rearward.
H / L (High/Low Range) Speed-Range Indicator Engine-Coolant-Temperature Indicator This display indicates the temperature of the engine coolant (Figure 14). This display indicates the selected speed range (Figure 14). Air-Intake-Heater Indicator This display indicates when the system is pre heating (Figure 14). Traction-Assist Indicator This display indicates when the traction assist is engaged (Figure 14).
Note: After you service the machine, reset the indicator. Resetting the Service-Interval Indicator 1. Press and hold the far, right button on the InfoCenter. Note: The Main Menu screen appears. 2. Select Service using the 2 buttons on the left; press the button below the right arrow to continue. 3. Select Hours and press the button below the right arrow. 4. Press the button below Reset Hours. 5. Select the Hours for the appropriate next service time and press the button below the right arrow.
To Set the Cruise Control 2. Disengage the PTO. Increase the ground speed. 3. Move the traction pedal to NEUTRAL. 4. Insert the jumper in teach plug. To Float the Deck 5. Engine running. Lower the decks. 6. Operator must be seated or set the parking brake. To Lower the Deck 7. Turn the key switch off then on. 1. The operator must be seated. 8. Wait. 2. Select the low range. For Teach (Traction Pedal Calibration) 3. Set the parking brake. Turn the key switch off then on.
Specifications Operation Note: Specifications and design are subject to change without notice. Note: Determine the left and right sides of the machine from the normal operating position.
Fuel Safety Checking the Engine-Oil Level Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 44). DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Checking the Cooling System • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills.
Checking the Tire Pressure • Monitor seals, hoses, and gaskets in contact with fuel as they may degrade over time. Service Interval: Before each use or daily • Fuel-filter plugging may be expected for a time after converting to biodiesel blended. The correct air pressure in the front tires is 345 kPa (50 psi ) and the rear tires is 207 kPa (30 psi) as shown in (Figure 20). • Contact your distributor if you wish more information on biodiesel.
Adjusting the Height of Cut You can adjust the height of cut from 25 to 153 mm (1 to 6 inches) in 13 mm (1/2 inch) increments. To adjust the height of cut, position the castor-wheel axles in the upper or lower holes of the castor forks, add or remove an equal number of spacers from the castor forks, and adjust the rear chain (front deck only) to the desired holes. Adjusting the Front Mower Deck 1. Start the engine and raise the mower decks so you can change the height of cut. 2.
Note: When mowing at a height of cut below 51 mm (2-1/2 inches), move the skids, gage wheels, and rollers to the highest holes. Note: To prevent grass buildup between the wheel and the fork, operate the machine at the 64 mm (2-1/2 inch) height of cut or higher and install the axle bolt in the bottom caster-fork hole.
Adjusting the Mower Deck Anti-Scalp Rollers Adjusting the Skids Mount the outer skids in the lower position when operating at heights of cut greater than 64 mm (2-1/2 inches) and in the higher position when operating at heights of cut lower than 64 mm (2-1/2 inches). Mount the mower-deck gage wheels and roller in the lower position when operating at heights of cut greater than 64 mm (2-1/2 inches) and in the higher position when operating at heights of cut lower than 64 mm (2-1/2 inches).
Matching the Height of Cut Between Mower Decks Adjusting the Gage Wheels 1. Remove the bolt and nut securing the gage wheel to the mower-deck brackets (Figure 29). 1. Position the blade side to side on the outside spindle of both side mower decks. 2. Align the roller and spacer with the top holes in the brackets and secure them with the bolt and nut. 2. Measure from the floor to the tip of the cutting edge on both units and compare the measurements.
Adjusting the Mirrors Rear-View Mirror While sitting in the seat, adjust the rear-view mirror to attain the best view out of the rear window. Pull the lever rearward to tilt the mirror to reduce the brightness and glare of light (Figure 33). Figure 32 1. Left, front, outside caster arm 2. Left, front, inside caster arm 3. Right, front, inside caster arm 4. Right, front, outside caster arm Figure 33 1. Side-view mirrors 2. Rear-view mirror 6.
Checking the Safety-Interlock Switches Note: The engine should shut off. If it does not shut off, there is a malfunction in the interlock system that you should correct before resuming operation. 5. Sit on the seat, disengage the PTO, and start the engine. CAUTION 6. With the engine running, engage the PTO and raise each mower deck individually. If safety-interlock switches are disconnected or damaged, the machine could potentially operate unexpectedly, causing personal injury.
Slope Safety • Never raise the mower deck with the blades running. • Stop the machine and inspect the blades after striking an • • • • • • • • • • • • Slow down the machine and use extra care on hillsides. object or if there is an abnormal vibration in the machine. Make all necessary repairs before resuming operation. Stop the blades whenever you are not mowing, especially while crossing loose terrain such as gravel.
Understanding the Operating Characteristics G010392 Practice driving the machine, as it has a hydrostatic transmission, and its characteristics may differ from other turf-maintenance machines. To maintain enough power for the traction unit and implement while operating, regulate the traction pedal to keep the engine speed (rpm) high and constant. Decrease the ground speed as the load on the implement increases, and increase the ground speed as the load decreases.
Transporting the Machine After Operation Use the transport latches when transporting the machine over long distances or rough terrain or when trailering. After Operation Safety General Safety • Clean grass and debris from the cutting units, drives, mufflers, and engine to help prevent fires. Clean up oil or fuel spills. • Shut off the fuel while storing or transporting the machine. • Disengage the drive to the attachment whenever you are transporting or not using the machine.
Identifying the Tie-Down Points Front of the machine—under the front of the operator's platform (Figure 38) Figure 40 1. Bypass valve Figure 38 2. Rotate each valve 3 turns counter-clockwise to open and allow oil to bypass internally. 1. Front tie downs Important: Do not open the valves more than 3 turns. Rear of the machine—on the bumper (Figure 39) Note: Because fluid is bypassed, you can slowly move the machine without damaging the transmission. 3.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Important: Refer to your Engine Operator's Manual for additional maintenance procedures. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • • • • After the first 250 hours • Adjust the valve clearance. • Change the planetary-drive gear/brake oil. Before each use or daily • • • • • • Torque the wheel-lug nuts.
Maintenance Service Interval Every 2,000 hours Every 2 years Maintenance Procedure • Adjust the valve clearance. • Flush the cooling system and replace fluid. • Replace moving hoses. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance. Service Interval Chart Figure 42 Premaintenance Procedures 6. Move the throttle switch to the LOW -IDLE position. 7.
• Carefully release pressure from components with stored energy. • If your machine requires major repairs or if you desire assistance, contact an Authorized Toro Distributor. • Use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty. Preparing the Machine for Maintenance Figure 44 1. Ensure that the PTO is disengaged. 1. Rear jacking point 2.
Lubrication Greasing the Bearings and Bushings Service Interval: Before each use or daily—Lubricate the caster-arm bushings. Every 50 hours—Lubricate all grease fittings. The machine has grease fittings that you must lubricate regularly with No. 2 lithium grease. Also, lubricate the machine immediately after every washing. Figure 46 1. Slide the cover inward approximately 2.5 cm (1 inch). 2. Disengage these cover edges. Note: Lubricate the caster-fork-shaft bushings before each use or daily. 6.
Figure 48 Figure 49 Figure 51 Figure 50 41
Front Mower Deck Side Mower Decks (Each Side) • 2 caster-fork-shaft bushings (Figure 52) • 4 caster-fork-shaft bushings (Figure 54) • 5 spindle-shaft bearings (located on the spindle housing) • 3 spindle-shaft bearings (located on the spindle housing) as shown in Figure 52 as shown in Figure 54 • 3 idler-arm-pivot bushings (located on the idler-pivot • 2 idler-arm-pivot bushings (located on the idler-pivot shaft) as shown in Figure 52 shaft) as shown in Figure 54 Figure 52 Figure 54 Front Lift
Engine Maintenance cleaning process prevents debris from migrating into the intake when you remove the primary filter. 2. Remove the primary filter (Figure 57). Engine Safety Note: Do not clean a used element due to the possibility of damage to the filter media. Shut off the engine before checking the oil or adding oil to the crankcase. Air-Cleaner Maintenance Check the air-cleaner body for damage that could cause an air leak and replace it if it is damaged.
6. Clean the dirt-ejection port located in the removable cover. 7. Remove the rubber outlet valve from the cover, clean the cavity, and replace the outlet valve. 8. Install the cover orienting the rubber outlet valve in a downward position - between approximately 5:00 to 7:00 when viewed from the end (Figure 57). 9. Secure the latch. Servicing the Engine Oil Checking the Engine-Oil Level Service Interval: Before each use or daily—Check the engine-oil level. Figure 59 1.
Changing the Engine Oil Fuel System Maintenance Service Interval: Every 250 hours—Change the engine oil and filter. 1. Remove the drain plug and let the oil flow into a drain pan (Figure 61). Servicing the Fuel System Draining the Fuel Tank Service Interval: Every 1,000 hours—Drain and clean the fuel tank. Drain and clean the tank if fuel system becomes contaminated or if you are storing the machine for an extended period of time. Use clean fuel to flush out the tank.
Servicing the Water Separator 8. Apply a coating of clean fuel or engine oil to the new O-ring and element seal. Service Interval: Before each use or daily—Drain the water separator. 9. Spin the bowl onto the new element, then spin them both onto the filter head by hand only. Every 500 hours—Replace the fuel/water separator element. Note: Do not use tools. 10. Close the drain plug. Draining the Water Separator 11. Connect the water sensor (electrical connector) from the bottom of the water separator.
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Battery acid is poisonous and can cause burns. Avoid contact with your skin, eyes, and clothing. Protect your face, eyes, and clothing when working with a battery. • Battery gases can explode. Keep cigarettes, sparks, and Figure 64 1. Fuel filter 3. Water Separator 2.
The cab fuses (Figure 68) are located in the fuse box on the cab headliner (Figure 69). Figure 68 Figure 66 1. Power-center console 2. Knob G021 159 1 2 Figure 69 3 1. Cab fuse box 2. Fuses Figure 67 1. Fuse—60 A 3. Alternate positive post for charging or jump starting Checking the Battery Condition 2. Fuse block Service Interval: Every 50 hours—Check the condition of the battery.
Charging the Battery Battery-charger Table WARNING Charging the battery produces gasses that can explode. Charger setting Charging time 4 to 6 amperes 30 minutes 25 to 30 amperes 10 to 15 minutes 7. When the battery is fully charged, unplug the charger from the electrical source, then disconnect the charger leads from the battery posts (Figure 70). Do not smoke near the battery, and keep sparks and flames away from the battery. Important: Keep the battery fully charged.
Drive System Maintenance Adjusting the Traction-Pedal Angle You can adjust the operating angle of the traction pedal for your comfort. g019500 Figure 72 1. Loosen the 2 nuts and bolts securing the left side of the traction pedal to the bracket (Figure 71). 1. Check/drain plug (3 o'clock position) 2. Remove the plug at the 3 o’clock position (Figure 72). Note: The oil level should be within 6 mm (1/4 inch) of the check-plug hole. 3.
Checking the Rear-Wheel Toe-in Service Interval: Every 1,000 hours—Check the rear-wheel toe-in. 1. Measure the center-to-center distance (at axle height) at the front and rear of the steering tires (Figure 76). Note: The front measurement cannot be more than 3 mm (0.12 inch) less than the rear measurement. g021 156 Figure 74 1. Drain plug 2. Brake housing 4. When all of the oil has drained from both locations, install the plug in the brake housing. 5.
Cooling System Maintenance The rotating fans and drive belts can cause personal injury. Cooling System Safety • Do not operate the machine without the covers in place. DANGER • Keep fingers, hands, and clothing clear of the rotating fan and drive belt. CAUTION Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. • Shut off the engine and remove the ignition key before performing maintenance.
Brake Maintenance Servicing the Engine-Cooling System Adjusting the Service Brakes Service Interval: Every 100 hours—Inspect the cooling-system hoses. Adjust the service brakes when there is more than 50 mm (2 inches) of “free travel” of the brake pedal or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before you feel braking resistance. Every 2 years—Flush the cooling system and replace fluid.
Belt Maintenance Replacing the Blade-Drive Belts Servicing the Alternator Belt Service Interval: Every 50 hours—Inspect the blade-drive belts. Service Interval: After the first 10 hours—Check the alternator-belt tension. Every 1,000 hours—Replace the blade-drive belts. The blade-drive belt, tensioned by the spring-loaded idler pulley, is very durable. However, after many hours of use, the belt will show signs of wear.
Figure 82 1. Hydraulic motor 2. Mounting bolts 6. Lift the motor off the mower deck and lay it on top of the mower deck. Figure 84 1. Idler pulleys 7. Remove the old belt from around the spindle pulleys and idler pulley. 6. Remove the old belt from around the spindle pulleys and idler pulley. 8. Route the new belt around the spindle pulleys and idler-pulley assembly (Figure 83). 7. Route the new belt around the spindle pulleys and idler-pulley assembly (Figure 85 and Figure 86).
Hydraulic System Maintenance High Viscosity Index/Low Pour Point Anti-wear Hydraulic Fluid, ISO VG 46 (cont'd.) Hydraulic System Safety WARNING 140 to 160 Pour Point, ASTM D97 -34° F to -49° F FZG, Fail stage Hydraulic fluid escaping under pressure can penetrate skin and cause injury.
Changing the Hydraulic Fluid and Filters Service Interval: Every 1,000 hours—Change the hydraulic fluid and filters. If the fluid becomes contaminated, contact your local Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. Use Toro replacement filters (Part No. 86–6110 for the left side of the machine and 75-1310 for the right side of the machine). Important: Use of any other filter may void the warranty on some components. 1.
Mower Maintenance 10. Start the engine and use all of the hydraulic controls to distribute hydraulic fluid throughout the system. Check for leaks, then shut off the engine. Pivoting (Tilting) the Front Mower Deck Upright 11. Check the fluid level and add enough to raise level the level to the Full mark on the dipstick. Important: Do not overfill. Note: Although not needed for normal maintenance procedures, you can pivot (tilt) the front mower deck upright. Checking the Hydraulic Lines and Hoses 1.
Adjusting the Mower-Deck Pitch Measuring the Mower-Deck Pitch The mower-deck pitch is the difference between the height-of-cut from the front of the blade plane to that of the back of the blade plane. Set a blade pitch of 7.5 mm (0.3 inch); i.e., the back of the blade plane should be 7.5 mm (0.3 inch) higher than the front of the blade plane. 1. Position the machine on a level surface on the floor. 2. Set the mower deck to the desired height of cut. 3.
2. Position the shims, as required, to raise or lower the castor wheel until the mower deck has the correct pitch. 3. Install the tensioning cap. Servicing the Castor-Arm Bushings The caster arms have bushings pressed into the top and bottom of the tube, and after many hours of operation, the bushings wear. To check the bushings, move the caster fork back and forth and from side to side. If the caster spindle is loose inside the bushings, the bushings are worn and must be replaced. 1.
Blade Maintenance Servicing the Caster Wheels and Bearings Blade Safety Service Interval: Every 500 hours—Inspect the mower-deck caster-wheel assemblies. DANGER 1. Remove the locknut from the bolt holding the caster-wheel assembly between the caster fork or the caster-pivot arm (Figure 97). A worn or damaged blade can break, and a piece of the blade could be thrown at you or bystanders, resulting in serious personal injury or death.
Inspecting and Sharpening the Cutter Blade(s) blade is bent and must be replaced; refer to Removing and Installing a Blade (page 62). Removing and Installing a Blade Service Interval: After the first 10 hours Every 50 hours Before each use or daily Replace the blade if it hits a solid object, if it is out of balance, or if it is bent. Always use genuine Toro replacement blades to be sure of safety and optimum performance.
Miscellaneous Maintenance Servicing the Spark-Arrestor Muffler Figure 101 1. Sharpen at the original angle. Service Interval: Every 250 hours—Service the spark arrestor. Note: Sharpen only the top of the cutting edge and maintain the original cutting angle to ensure the sharpness. 1. Remove the pipe plug from the clean-out port at the lower side of the muffler. CAUTION Note: The blade will remain balanced if the same amount of metal is removed from both cutting edges.
Cleaning the Cab Air Filters 3. Install the filters and the grate with the thumb screws. Service Interval: Every 250 hours Cleaning the Air-Conditioning Assembly 1. Remove the screws and grates from both the in-cab and rear cab air filters (Figure 102 and Figure 103). 1 Service Interval: Every 250 hours (more frequently in extremely dusty or dirty conditions). 2 1. Perform the premaintenance procedure; refer to Preparing the Machine for Maintenance (page 39). 2. Disconnect the wire for each fan.
Storage Preparing for Seasonal Storage Traction Unit 1. Thoroughly clean the traction unit, mower decks, and the engine. Important: Do not use high-pressure water near Info Center 2. Check the tire pressure; refer to Checking the Tire Pressure (page 26). 3. Check all fasteners for looseness; tighten as necessary. 4. Grease or oil all grease fittings and pivot points. Wipe up any excess lubricant. 5. Lightly sand and use touch-up paint on painted areas that are scratched, chipped, or rusted.
Notes: 66
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
