Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSecurity Cage Kit, Groundsmaster 4500, 4700, or Reelmaster 7000 Series Traction Unit with 2 Post ROPS Extension

FormNo.3419-943RevB

SecurityCageKit

Groundsmaster

4500,4700,orReelmaster

7000SeriesTraction

Unitwith2PostROPSExtension

ModelNo.31606

InstallationInstructions

Thiskitts2-PostROPSExtensionKitModel31351only.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Note:Haveanassistanthelpyoutoinstallthiskit.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Lowerthecuttingunits.

3.Engagetheparkingbrake.

4.Shutofftheengineandremovethekey.

5.Iftherearelightsontherollbar,removethelightsandmountinghardwarefromtherollbar.

Retainthelightsandthemountinghardware

6.Ifa2PostROPSextensionwasinstalledonthemachine,removethesidepanelsthatareusedto

mounttheROPSpostlights(Figure2).

Note:RetaintheROPSclampsandcorrespondinghardware.

7.Positionthecontrolconsoletothefurthestinwardposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3419-943*B

Summary of content (8 pages)

PAGE 1
Form No. 3419-943 Rev B Security Cage Kit Groundsmaster® 4500, 4700, or Reelmaster® 7000 Series Traction Unit with 2 Post ROPS Extension Model No. 31606 Installation Instructions This kit fits 2-Post ROPS Extension Kit Model 31351 only. Note: Determine the left and right sides of the machine from the normal operating position. Note: Have an assistant help you to install this kit. 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Lower the cutting units.
PAGE 2
Procedure 2 Refer to Figure 2 as you perform the following steps. Note: Ensure that all parts are assembled loose. Assembling the Cage Complete the assembly of the kit; then, tighten all fasteners.
PAGE 3
g205385 Figure 1 Left side shown 1. Drill holes—0.281 inch 3. Left lower-panel assembly 2. Foot platform 9. Secure the left and right door cage assemblies to the corresponding side of the machine. Place the hinge assembly connected to each door onto the previously installed door-mount assemblies with 4 spacers. 10. Use 4 ball studs and 4 flange nuts (5/16 inch) to secure the springs to the door cage assemblies and the spring mounts.
PAGE 4
g211833 Figure 2 1. Flange nut (5/16 inch) 10. Left door mount 19. Flange nut (1/4 inch) 2. Left door support 11. Right door mount 20. Bolt (5/16 x 3/4 inch) 3. Right door support 12. Upper mount bracket 21. Roll bar 4. Rear screen 13. Lower mount bracket 22. Side panels—2 post ROPS extension 5. Left-door-cage assembly 14. Gas spring 23. Top rails—2 post ROPS extension 6. Right-door-cage assembly 15. Spring mount 7. Rear panel 16. Spacer 24. Lower side bracket—2 post ROPS extension 25.
PAGE 5
6. 3 4 Assembling the Door Latch Parts needed for this procedure: 2 Jam nut 2 Pin guard 2 Latch-pin cam 4 Thrust washer 4 Lock washer 2 Latch pin Adjusting the Door-Latch Pins No Parts Required Procedure 1. Procedure 1. 2. Tighten the jam nut onto the latch pin by hand (Figure 3). Center the latch pin in the latch-pin-mount bracket on the rail (Figure 4). Ensure that you adjusted the control console to the furthest inward position.
PAGE 6
Note: If the height measured is more than the zone specification, rotate the latch-pin cam 45° toward the inside of the cab to achieve the specified measurement. If the height measured is less than the zone specification, perform the opposite of the above procedure. 5 Adjusting the Doors Note: The latch pin self centers. No Parts Required Procedure 1. Loosen the door-latch pin. 2. Shut the door and use a ratchet strap to hold the door (Figure 6).
PAGE 7
Procedure 6 Refer to Figure 7 as you perform the following steps. Note: Ensure that the upper windshield is installed so that the seam is positioned on the bottom of the frame. Installing the Windshield Parts needed for this procedure: 1 Dual-tab mount 2 Side-tab mount 1 Top-tab mount 6 Rivet 1 Lower-windshield assembly 1 Upper-windshield assembly 13 Bolt (5/16 x 1-1/2 inches) 13 Backup washer 13 Rubber bushing (0.31 inch long) 13 Rubber bushing (0.
PAGE 8
7 Completing the Installation No Parts Required Procedure 1. Ensure that all fasteners are tightened. 2. Install any attachments that you previously removed, such as lights, onto the left and right panels.