Installation Instructions

ManualsBrandsToro ManualsRiding ProductsTurn Signal Kit, Groundsmaster 4010, 4110, 5910, or 360 Series Rotary Mower with Cab

FormNo.3447-728RevA

TurnSignalKit

Groundsmaster

4010,4110,5910,or360SeriesRotaryMower

withCab

ModelNo.31671

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

CAUTION

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystarttheengine

andseriouslyinjureyouorbystanders.

Removethekeyfromtheignitionswitch

beforeyoudoanymaintenance.

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

DisconnectingtheBattery

NoPartsRequired

WARNING

Electricalsparkscancausethebatterygasses

toexplode,resultinginpersonalinjury.

Incorrectbatterycableroutingcoulddamage

themachineandcables,causingsparks.

•Alwaysdisconnectthenegative(black)

batterycablebeforedisconnectingthe

positive(red)cable.

•Alwaysconnectthepositive(red)battery

cablebeforeconnectingthenegative

(black)cable.

WARNING

Batteryterminalsormetaltoolscouldshort

againstmetalcomponents,causingsparks.

•Whenremovingorinstallingthebattery,

donotallowthebatteryterminalstotouch

anymetalpartsofthemachine.

•Donotallowmetaltoolstoshortbetween

thebatteryterminalsandmetalpartsofthe

machine.

•Alwayskeepthebatterystrapinplaceto

protectandsecurethebattery.

DisconnectingtheBattery

Groundsmaster4010SeriesorGroundsmaster

4110SeriesMachines

1.Openthebatterycompartmentdoor(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3447-728*

Summary of content (8 pages)

PAGE 1
Form No. 3447-728 Rev A Turn Signal Kit Groundsmaster® 4010, 4110, 5910, or 360 Series Rotary Mower with Cab Model No. 31671 Installation Instructions 2 Installation 1 Disconnecting the Battery Preparing the Machine No Parts Required WARNING No Parts Required Electrical sparks can cause the battery gasses to explode, resulting in personal injury. Procedure Incorrect battery cable routing could damage the machine and cables, causing sparks.
PAGE 2
g205862 Figure 1 2. Disconnect the negative (-) battery cable from the battery (Figure 2). g210583 Figure 3 2. Open the hood (Figure 3). 3. Rotate the battery disconnect switch to the OFF position (Figure 4). g205863 Figure 2 1. Negative battery post g210582 Figure 4 2. Terminal (negative battery cable) 1. Battery disconnect switch Disconnecting the Battery Groundsmaster 5900 Series Machines 1. Unlatch the hood latches at both sides of the hood (Figure 3).
PAGE 3
Disconnecting the Battery Groundsmaster 360 Series Machines Disconnect the negative (-) battery cable from the battery (Figure 5). g028770 Figure 6 g361658 Figure 5 1. Negative (-) battery cable 2.
PAGE 4
Installing the Front Lights 1. Remove the front light covers. 2. Apply the front light gasket to the front warning light (Figure 7). g361614 Figure 7 1. Front light gasket 3. 2. Front warning light Install the front warning lights to the headliner using 4 bolts, 4 washers, and 4 flange nuts (#10) as shown in Figure 8. g361771 Figure 9 1. Light connector g361615 Figure 8 1. Flange nut (#10) 3. Warning light 2. Washer 4. Bolt 4. Connect the front warning lights to the wire harness (Figure 9).
PAGE 5
Installing the Rear Warning Lights 1. Remove the rear warning light covers. 2. Apply the rear light gasket to the rear warning light (Figure 10). 4 Connecting the Battery No Parts Required Connecting the Battery Groundsmaster 4100 Series Machines 1. g361617 Figure 10 1. Rear light gasket 2. Rear warning light 3. Install the rear warning lights to the headliner using 4 bolts, 4 washers, and 4 flange nuts (#10) as shown in Figure 8. 4.
PAGE 6
2. Perform the following operational checks of the installed lights: Models Headlights *GM 4010 and 4110 Series X GM 5910 Models X GM 360 Models X Hazard Signal X X g210584 Figure 13 1. Battery disconnect switch 2. Test the lights of the kit. 3. Close the hood and latch it.
PAGE 7
Notes:
PAGE 8