Installation Instructions

ManualsBrandsToro ManualsRiding ProductsTurn Signal Kit, Groundsmaster 360, 3200, 3300, 4000, 5900, 7200 Series Rotary Mower or Reelmaster 3000, 5000 Series Traction Unit with ROPS

FormNo.3447-731RevA

TurnSignalKit

Groundsmaster

360,3200,3300,4000,5900,7200SeriesRotary

MowerorReelmaster

3000,5000SeriesTractionUnitwithROPS

ModelNo.31672

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.DisengagethePTOandlowertheattachment(s).

4.Shutofftheengineandremovethekey.

InstallingtheLightswitha

SunShade

Partsneededforthisprocedure:

2Lightbracket

8Largespeed-nut

Smallspeed-nut

Screw(#10x1-1/4inches)

2Frontlight

2Rearlight

Carriagebolt(5/16x1inch)

Flangenuts(5/16inch)

Carriagebolt(3/8x5inches)

Carriagebolt(3/8x4inches)

Carriagebolt(3/8x3inches)

Flangelocknuts(3/8inch)

2Mountingbracket

Procedure

Note:Thelocationofthesunshadesupport

determinesthelocationofthelightontherollbar.

1.Installthelargespeednutstothetopandbottom

ofthelightbracket(Figure1).

2.Installthesmallspeednutstothesidesofthe

lightbracket(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3447-731*

Summary of content (12 pages)

PAGE 1
Form No. 3447-731 Rev A Turn Signal Kit Groundsmaster® 360, 3200, 3300, 4000, 5900, 7200 Series Rotary Mower or Reelmaster® 3000, 5000 Series Traction Unit with ROPS Model No. 31672 Installation Instructions 2 Installation 1 Preparing the Machine Installing the Lights with a Sun Shade Parts needed for this procedure: No Parts Required Procedure 2 Light bracket 8 Large speed-nut 8 Small speed-nut 1. Park the machine on a level surface. 8 Screw (#10 x 1-1/4 inches) 2.
PAGE 2
g372853 Figure 1 1. Large speed nuts 3. Small speed nuts 2. Light bracket 3. 4. Determine which holes to use for installing the mounting bracket to the light bracket. Refer to the table below and Figure 3. g372741 Figure 3 Mounting Bracket Position in the Light Bracket Install the mounting bracket to the light bracket as shown in Figure 2. Note: Ensure the mounting-bracket tab is pointing backwards (Figure 2). Note: There are 2 positions for B and 2 in Figure 3.
PAGE 3
g372433 Figure 4 1. Sun shade 2. Bracket 6. Make note of which holes the existing U-bolts use when removing it. 7. Remove the U-bolt from the bracket attached to the sun-shade support. Discard the U-bolt. 8. Before installing the light assembly to the roll bar, you need to determine the length of bolts to use. Use the 3/8 inch carriage bolts that are 3, 4, or 5 inches long. 9. g372958 Figure 5 1. Rollbar 4. Existing sunshade bracket 2. Bolt (3/8 x 3, 4 or 5 inches) 5.
PAGE 4
2. Install the small speed nuts to the sides of the light bracket (Figure 7). g372930 Figure 6 1. Yellow lens 4. 2. Light bracket 5. Red lens 3. Rear light 6. Front light Screw (#10 x 1-1/4 inches) g372853 Figure 7 1. Large speed nuts 3. Small speed nuts 2.
PAGE 5
g372360 Figure 10 ReelMaster 3000 Series g372741 Figure 9 Positions for Mounting Bracket 1. 15.2 to 17.8 cm (6 to 7 inches) 2. Use these holes in the brackets. Note: There are 2 positions for B and 2 in Figure 9. The correct holes are determined if you are installing the lights on the left or right side of the ROPS. Ensure the lights point straight back.
PAGE 6
g372745 Figure 12 GroundsMaster 4000 and 4100 Series 1. 14.3 to 16.8 cm (5-5/8 to 6-5/8 inches) 2. Use these holes in the brackets. g372749 Figure 11 ReelMaster 5000 Series 1. 16.8 to 19.4 cm (6-5/8 to 7-5/8 inches) 3. Use these holes in the housing. 2. Use these holes in the brackets. 6 3. Use these holes in the housing.
PAGE 7
g372746 Figure 13 GroundsMaster 4500 Series 1. 19.0 to 21.6 cm (7-1/2 to 8-1/2 inches) g372743 Figure 14 GroundsMaster 3280 Series 3. Use these holes in the housing. 1. 15.9 to 18.4 cm (6-1/4 to 7-1/4 inches) 2. Use these holes in the brackets. 2. Use these holes in the brackets. 7 3. Use these holes in the housing.
PAGE 8
g372748 Figure 15 GroundsMaster 7200 Series 1. 15.9 to 18.4 cm (6-1/4 to 7-1/4 inches) g372744 Figure 16 GroundsMaster 360 Series 3. Use these holes in the housing. 1. 15.9 to 18.4 cm (6-1/4 to 7-1/4 inches) 2. Use these holes in the brackets. 2. Use these holes in the brackets. 8 3. Use these holes in the housing.
PAGE 9
g372747 Figure 17 GroundsMaster 5900 Series 1. 19.0 to 21.6 cm (7-1/2 to 8-1/2 inches) g372742 Figure 18 GroundsMaster 3200 and 3300 Series 3. Use these holes in the housing. 1. 15.9 to 18.4 cm (6-1/4 to 7-1/4 inches) 2. Use these holes in the brackets. 2. Use these holes in the brackets. 9 3. Use these holes in the housing.
PAGE 10
5. Before installing the light assembly to the roll bar, you need to determine the length of bolts to use. Use the 3/8 inch carriage bolts that are 3, 4, or 5 inches long. 6. Assemble the light assembly to the roll bar with rollbar bracket, 4 carriage bolts (3/8 x 3, 4 or 5 inches), and 4 flange locknuts (3/8 inch); refer to Figure 10 through Figure 18 and Figure 19. Note: The length of the carriage bolts is determined by the size of the rollbar on your machine.
PAGE 11
5 Connecting the Battery No Parts Required Connecting the Battery Groundsmaster 4100 Series Machines 1. Assemble the terminal of the negative battery cable to the negative post of the battery, and tighten the nut of the terminal by hand (Figure 23). g372875 Figure 21 1. Light connectors 3. 12-pin connector 2. Harness connectors 5. Install the cover onto the light brackets with 8 bolts (1/4 x 3/4 inch); refer to . g205861 Figure 23 1. Terminal (negative battery cable) 2.
PAGE 12
g210584 Figure 24 1. Battery disconnect switch 2. Test the lights of the kit. 3. Close the hood and latch it.