Installation Instructions

ManualsBrandsToro ManualsRiding ProductsLED Light Kit, Groundsmaster 3500 Series Rotary Mower or Reelmaster 3100-D Series Traction Unit

FormNo.3449-380RevB

LEDLightKit

Groundsmaster

3500SeriesRotaryMowerorReelmaster

3100-D

SeriesTractionUnit

ModelNo.31692

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Drilltheholefortheswitch.

Lightbracket2

Bolt(5/16x1/2inches)

Nut(5/16inch)

Lightassembly2

Hex-headangebolt(5/16x3/4inches)

Installthelightassemblies.

Wireharness(blackandbluelight

connectors)

Wireharness15.2cm(6inch)

Switchassembly

Installthewireharnesses.

Note:Retainallremovedpartsforlaterinstallationunlessotherwisenoted.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.DisengagethePTOandengagetheparking

brake.

3.Lowerthecuttingunit.

4.Shutofftheengineandremovethekey.

5.Waitforallmovingpartstostop.

6.Allowtheenginetocoolcompletely.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3449-380*

Summary of content (8 pages)

PAGE 1
Form No. 3449-380 Rev B LED Light Kit Groundsmaster® 3500 Series Rotary Mower or Reelmaster® 3100-D Series Traction Unit Model No. 31692 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. No parts required – Prepare the machine. No parts required – Drill the hole for the switch.
PAGE 2
WARNING 2 Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Drilling the Hole for the Switch • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. No Parts Required Procedure 1. • Always connect the positive (red) battery cable before connecting the negative (black) cable. Remove the cover from the battery box (Figure 1). 2.
PAGE 3
5. Using the dimensions shown in Figure 3, locate, mark, and drill a 13 mm (1/2 inch) diameter hole in the control panel. 3 Installing the Light Assemblies Parts needed for this procedure: 2 Light bracket 2 Bolt (5/16 x 1/2 inches) 6 Nut (5/16 inch) 2 Light assembly 4 Hex-head flange bolt (5/16 x 3/4 inches) g312592 Figure 3 1. 13 mm (1/2 inch) hole Procedure 3. 25 mm (1 inch) 2. 11.7 cm (4-5/8 inches) Note: Install the control panel after you install the harness to the switch.
PAGE 4
Installing the Wire Harnesses Parts needed for this procedure: 1 Wire harness (black and blue light connectors) 1 Wire harness 15.2 cm (6 inch) 1 Switch assembly Procedure Use this procedure for traction units with the following serial number ranges. • Reelmaster 3100 with serial numbers 240000001 to present • Groundsmaster 3500 with serial numbers 240000001 to present • Groundsmaster 3505 with serial numbers 250000001 to present 1.
PAGE 5
. Mount the switch to control panel with the hex nuts and lock washer (Figure 5). Note: The key way slot in the switch mounting threads indicates the OFF position. g312595 Figure 5 1. Switch 6. Connect the 15.2 cm (6 inch) long harness with the blue and white terminals to the light switch as follows: • Connect the blue wired ring terminal to the center bottom terminal of the switch with the washer and screw (Figure 6).
PAGE 6
g369746 Figure 6 1. Switch 2. Washer 7. Blue wired male terminal 8. Battery clamp/ground stud 3. White-wired ring terminal 9. Cable tie 4. Blue-wired ring terminal 10. Black and blue wired connectors (2) 5. Screw 6. White wired male terminal 11. Blue wire with female terminal 7. Connect the white wired male terminal on the harness to the white wired female terminal below the control panel on the main wire harness. 8.
PAGE 7
9. Install the 10 amp fuse into the open receptacle in the fuse block (Figure 7). g312759 Figure 7 1. Fuse 10. Install the control panel shroud. 11. Remove and discard the existing negative (-) battery cable clamp bolt (Figure 8). g312760 Figure 8 1. Negative (-) battery cable 12. Loosely install the new battery clamp bolt/ground stud (Figure 9). g312758 Figure 9 1. Battery clamp/ground stud 13. Connect the black wired ring terminal to the ground stud. 7 14.
PAGE 8