Installation Instructions

ManualsBrandsToro ManualsRiding ProductsAuxiliary Braking System, Serial Number 400000000 and After Groundsmaster 5900 Rotary Mower

Table Of Contents

FormNo.3417-645RevA

AuxiliaryBrakingSystem

SerialNumber400000000andAfterGroundsmaster

5900Rotary

Mower

ModelNo.31701

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal136-0007

136-0007

1.Brakes

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Disconnectthebattery.

Switch

Auxiliary-brakedecal1

Installtheswitchanddecal.

Wireharness1Routethewireharness.

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Enablethebrakesystem.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3417-645*A

Summary of content (8 pages)

PAGE 1
Form No. 3417-645 Rev A Auxiliary Braking System Serial Number 400000000 and After Groundsmaster® 5900 Rotary Mower Model No. 31701 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. g038719 Figure 1 2 Disconnecting the Battery No Parts Required Procedure Turn the battery-disconnect switch to the OFF position (Figure 2).
PAGE 3
Installing the Switch and Decal Parts needed for this procedure: 1 Switch 1 Auxiliary-brake decal g186717 Figure 4 3. Plug 1. Switch 2. Auxiliary-brake decal Procedure 1. 4. Remove the 6 bolts from the side panel and remove the side panel from the console (Figure 3). Adhere the auxiliary-brake decal above the switch (Figure 4). 4 Note: Retain and set aside the bolts. Routing the Wire Harness Parts needed for this procedure: 1 Wire harness Procedure 1.
PAGE 4
2. Connect the wire harness to the EU light power connector inside the console (Figure 5). 3. Use the previously removed bolts to install the back and side panels to the console (Figure 3). 4. Following the existing wire harness, route the section of the wire harness with the ring-terminal connector through the hole in the electrical cover plate, behind the seat. No Parts Required Secure the ring-terminal connector to an empty terminal on the ground block (Figure 6). Procedure 5.
PAGE 5
Operation Using the Auxiliary-Brake Switch Press and hold the auxiliary-brake switch to decrease the engine speed (Figure 8); release the switch to stop the deceleration and remain at the current engine speed. Note: You may use the switch intermittently to gradually slow the machine. If you press the switch when the engine speed is below 1,200 rpm or if the engine decelerates to 1,200 rpm, the engine shuts off and the machine stops. To start the machine again: 1. Turn the key switch to the STOP position.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8