Installation Instructions

ManualsBrandsToro ManualsRiding ProductsHomologation Kit, Groundsmaster 1200 Series Pull Behind Rotary Mower

FormNo.3429-633RevA

HomologationKit

Groundsmaster

1200SeriesPullBehindRotaryMower

ModelNo.31950

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Lefttaillightsupport

Righttaillightsupport1

Reectortriangle

Screw(#10-24x3/4inch)

Locknut(#10-24)

Assemblethetaillights.

Capscrew(5/16x4inches)

Washer(5/16inch)

Flangelocknut(5/16inch)

Assemblethetaillightstothemachine.

Wireharnessbracket2Installthewireharnessbrackets.

Cableties

4Routeandconnectthewireharness.

Nopartsrequired

–

Connectthewireharnesstothetow

vehicle.

PreparingtheMachine

NoPartsRequired

Procedure

1.Connectthemachinetothetowvehicle;referto

theOperator'sManualforthemachine.

2.Lowerthemowerdecks;refertotheOperator’s

Manualforyourmachine.

3.Engagetheparkingbrakeforthetowvehicle,

shutofftheengine,removethekey,andwait

forallmovingpartstostopbeforeleavingthe

operator’sseat.

4.Lowerthejackanddisconnectthemachinefrom

thetowvehicle;refertotheOperator'sManual

forthemachine.

5.Chockthetiresofthemachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3429-633*A

Summary of content (8 pages)

PAGE 1
Form No. 3429-633 Rev A Homologation Kit Groundsmaster® 1200 Series Pull Behind Rotary Mower Model No. 31950 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Qty.
PAGE 2
3. 2 Assembling the Taillights to the Taillight Support Assembling the Tail Lights 1. Parts needed for this procedure: 1 Left taillight support 1 Right taillight support 2 Reflector triangle 4 Screw (#10-24 x 3/4 inch) 4 Locknut (#10-24) Repeat steps 1 and 2 for the other reflector and taillight support. Remove the 4 nuts from the 2 tail light assemblies. Assembling the Reflectors to the Light Support 1.
PAGE 3
g280310 g280317 Figure 3 1. Taillight harness 3. Push-in fastener (harness) 2. Taillight-support tube 3 Assembling the Taillights to the Machine g280311 Figure 4 Parts needed for this procedure: 4 Capscrew (5/16 x 4 inches) 4 Washer (5/16 inch) 4 Flange locknut (5/16 inch) 1. Left taillight assembly 5. Flange locknut (5/16 inch) 2. Right taillight assembly 6. Capscrew (5/16 x 4 inches) 3. Taillight-support tube 7. Washer (5/16 inch) 4. Axle-frame tube 2.
PAGE 4
g280318 Figure 5 1. Left taillight assembly 3. Left, upper gusset plate (axle-frame tube) 2. Push-in fastener (harness) 4 Installing the Wire Harness Brackets g280308 Figure 6 Parts needed for this procedure: 2 4. Capscrew (1/2 x 4-1/2 inches) 2. Clevis 3. Washer (1/2 inch) 5. Harness bracket Wire harness bracket Installing the Forward Wire Harness Bracket 1. 1.
PAGE 5
Installing the Rear Wire Harness Bracket 1. Remove the 2 flange locknuts (1/2 inch), 2 capscrews (1/2 x 4-1/2 inches), and 2 washers (1/2 inch) that secure the hitch tube to the receiver (Figure 7). g280309 Figure 8 g280312 Figure 7 1. Capscrew (1/2 x 4-1/2 inches) 4. Flange locknut (1/2 inch) 2. Washer (1/2 inch) 5. Harness bracket 3. Receiver tube 2. Align the holes in the harness bracket with the holes in the receiver as shown in Figure 7. 3.
PAGE 6
5 Routing and Connecting the Wire Harness Parts needed for this procedure: 4 Cable ties Routing and Connecting the Harness at the Axle-Frame Tube 1. Route the 7-contact connector of the wire harness along the right frame tube as shown in Figure 9. g280316 Figure 10 1. Holes—axle-frame tube 6 mm (1/4 inch) 5. Push-in fastener (harness) 2. Wire harness 6. 4-socket connector—wire harness TAIL LIGHT (LEFT) 3. 4-pin connector (right taillight harness) 7. 4-pin connector (left taillight harness) 4.
PAGE 7
Routing the Harness at the Frame 1. Route the wire harness along the right frame tube as shown in Figure 11. g280319 Figure 13 1. Hydraulic tubes 4. Right frame tube 2. Push-in fastener (harness) 5. Cable ties 3. Magnetic fastener (harness) g280323 Figure 11 1. Push-in fastener (harness) 3. Right taillight harness 2. Right, upper gusset plate (axle-frame tube) 5. 4. Wire harness 2.
PAGE 8
g280326 Figure 15 1. Forward harness bracket 2. Harness push-in fastener 6 Connecting the Wire Harness to the Tow Vehicle g280315 Figure 16 1. Trailer connector (4 socket 3. Harness bracket (forward and 3 pin contacts) position) No Parts Required 2. 7-contact connector (wire harness) 4. Cable tie Procedure Your tow vehicle needs a trailer 7-contact connector with 4 sockets and 3 pins; refer to your authorized Toro distributor for parts. 1.