Installation Instructions

ManualsBrandsToro ManualsRiding ProductsCE Kit, Groundsmaster 3200 or 3300 Series Traction Unit

FormNo.3446-442RevA

CEKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31953

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal131-3393

131-3393

1.ReadtheOperator'sManual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3446-442*

Summary of content (12 pages)

PAGE 1
Form No. 3446-442 Rev A CE Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31953 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal131-3393 131-3393 1. Read the Operator's Manual. © 2021—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com.
PAGE 2
Installation Note: Determine the left and right sides of the machine from the operating position. 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Lower the attachment. 4. Shut off the engine and remove the key. 2 decal144-3952 144-3952 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal.
PAGE 3
g303095 Figure 1 1. Template 3. Drill 3 holes into the hood as shown in Figure 2. g303415 Figure 3 1. Latch bracket 5. 2. Existing hardware Use 2 rivets (1/2 inch) to secure the latch plates to the hood (Figure 4). g303094 Figure 2 1. Drill hole—0.48 cm (3/16 inch) 4. 2. Drill hole—2.06 cm (13/16 inch) Use the existing hood-strap hardware to secure the latch bracket to the hood strap (Figure 3). g305610 Figure 4 1. Latch plate 3 2. Rivet (1/2 inch) 6.
PAGE 4
3 Installing the Decals Parts needed for this procedure: 1 Slope decal (Part No. 144-3952) 1 CE and sound decal (Part No. 131-3393) g303938 Figure 5 1. Jam nut Procedure 2. Key latch 8. Use the previously-removed jam nut (Figure 5) to secure the key latch to the hood. 9. Lower the hood and use the key to secure the hood in the lowered position. Apply the decals to a clean and dry surface. • Perform the following steps to install the slope decal: 1.
PAGE 5
Slope Decal per Traction Unit and Attachment Configuration Traction Unit Model Number 31900 31901 Attachment Model Number or Name Slope Decal Decal to meet required slope standard* Decal for improved slope performance* 31970 A E 31970 and Sunshade A D 31971 A E 31971 and Sunshade A D 31972 A D 31972 and Sunshade B C 31973 A D 31973 and Sunshade B C 31974 A E 31974 and Sunshade A D 31975 A D 31975 and Sunshade B C 02835 B C 02835 and Sunshade A B 31970 B G 3
PAGE 6
Slope Decal per Traction Unit and Attachment Configuration (cont'd.
PAGE 7
2. Peel the appropriate slope decal from the backing and discard the remaining decals. 3. Install the slope decal (Part No. 144-3952) on the existing warning-decal location as shown in Figure 6.
PAGE 8
g319044 g354041 Figure 8 Figure 7 1. Cable bracket 2. Throttle cable 1. Rivet 3. Jam nuts 5. Adjust the throttle cable in the bracket (Figure 7) to attain a speed of 3,100 rpm. 6. Tighten the throttle-cable jam nuts. 7. Shut off the engine and remove the key. 8. Use 2 rivets (1/8 inch) to install the cable guards around the throttle-cable jam nuts (Figure 8). 2.
PAGE 9
g318787
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12