Installation Instructions

ManualsBrandsToro ManualsRiding ProductsAuxiliary Hydraulic Kit, Groundsmaster 3200 or 3300 Series Traction Unit

FormNo.3439-353RevA

AuxiliaryHydraulicKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31966

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Manifold

Switch

Carriagebolt(5/16x1inch)

Locknut(5/16inch)

Malecoupler1

Femalecoupler1

Bolt(5/16x3/4inch)

12Vport1

Hydraulictube1

Installthemanifold.

Wireharness1

Magneticclip8

Cabletie

Routethewireharness.

PreparingtheMachine

NoPartsRequired

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.ShifttotheNEUTRALposition.

3.Lowerallattachments(ifequipped).

4.Engagetheparkingbrake.

5.Shutofftheengineandremovethekey.

6.Disconnectthebattery;refertoyourmachine

Operator’sManual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3439-353*

Summary of content (8 pages)

PAGE 1
Form No. 3439-353 Rev A Auxiliary Hydraulic Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31966 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty.
PAGE 2
Installing the Manifold Parts needed for this procedure: 1 Manifold 2 Switch 2 Carriage bolt (5/16 x 1 inch) 2 Locknut (5/16 inch) 1 Male coupler 1 Female coupler 3 Bolt (5/16 x 3/4 inch) 1 12V port 1 Hydraulic tube g309211 Figure 2 1. Carriage bolt (5/16 x 1 inch) 3. Locknut (5/16 inch) 2. Bracket with manifold Procedure 1. Install the male and female hydraulic connectors to the manifold (Figure 1). 2.
PAGE 3
6. Install the hydraulic tube to the steering valve where the hose was removed (Figure 4). 7. Connect the hydraulic tube to the manifold as shown in Figure 4. 8. Connect the hydraulic hose to the manifold as shown in Figure 4. g309183 Figure 4 Bottom of the machine 1. Existing hose 4. Front of the machine 2. Correct location for the hose and tube in the manifold 3. Manifold 5.
PAGE 4
3 Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 8 Magnetic clip 2 Cable tie Procedure 1. Loosen the bolts around the steering-column base (Figure 5) 2. Raise the base up and drill a 22 mm (7/8 inch) hole as shown in Figure 5. g304291 Figure 6 1. Screw 2. Control cover 6. Install the connectors for the switches into the switch mount on the steering column (Figure 7). 7. Install the switches into the connectors and switch mount (Figure 7). g304296 Figure 5 1.
PAGE 5
8. Connect the wire harness to the 12V port (Figure 8). 11. Connect the wire-harness power connector to the main machine-harness cab-power connector, which is located near the right roll-bar post and adjacent to the pump pulley (Figure 8). 12. Connect the harness and the battery cables to the battery; refer to your machine Operator’s Manual. • Connect the blue wire to the negative (-) terminal. • Connect the white wire to the positive (+) terminal. 9. 10.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8