Installation Instructions

ManualsBrandsToro ManualsRiding ProductsMehanical Suspension Seat Kit, Groundsmaster 3200 or 3300 SeriesTraction Unit

FormNo.3434-642RevA

SeatKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31980—SerialNo.400000000andUp

ModelNo.31981—SerialNo.400000000andUp

ModelNo.31982—SerialNo.400000000andUp

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowerthecuttingunit.

4.Shutofftheengineandremovethekey.

5.Disconnectthebattery;refertotheelectrical

systemmaintenancesectionofyourOperator’s

Manual.

InstallingtheSeattothe

TractionUnit

Partsneededforthisprocedure:

4Bolt

8Nut

1Plate

Seat-switchwireharness

Air-ride-seatwireharness(ModelNo.31982only)

PositioningtheSeatAssembly

1.Removetheconsolefromtheseatbaseand

retainthenuts.

Important:Ensurethatyousupportthe

consoleafterremovingitsothatitdoesnot

crimporhangbythecablesandwires.

2.Installtheendoftheseat-switchwireharness

labeledP2(SeatSwitch)totheseat-switch

connectorundertheseat.

3.Aligntheseatstudswiththeholesintheseat

base(Figure1).

g299316

Figure1

ModelNo.31980shown.

1.Seat2.Seatbase

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3434-642*A

Summary of content (8 pages)

PAGE 1
Form No. 3434-642 Rev A Seat Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31980—Serial No. 400000000 and Up Model No. 31981—Serial No. 400000000 and Up Model No. 31982—Serial No. 400000000 and Up Installation Instructions Installation Important: Ensure that you support the console after removing it so that it does not crimp or hang by the cables and wires. 1 Preparing the Machine 2.
PAGE 2
Routing the Wire Harness Completing the Installation 1. Note: Model No. 31980 and 31981 are equipped with 1 wire harness (i.e., the seat-switch wire harness). Model No. 31982 is equipped with 2 wire harnesses (i.e., the seat-switch wire harness and the air-ride-seat wire harness). Use 4 nuts to secure the seat to the seat base (Figure 3). • Installing the Seat-Switch Wire Harness: 1. Route the seat-switch harness between the seat and seat base and towards the machine wire harness (Figure 2). 2.
PAGE 3
Tighten the carriage bolt and nut, then tighten the existing nuts to the console studs. 4. Secure the plate to the seat bracket with 3 carriage bolts and 3 nuts (B in Figure 4). 3 Connect the Battery No Parts Required Procedure Connect the battery; refer to the electrical system maintenance section of your Operator’s Manual. g299331 Figure 4 1. Carriage bolt 4. Nuts 2. Throttle cable 3. Machine wire harness 5. Plate 3.
PAGE 4
Weight-Adjustment Dial Product Overview Model No. 31981 Only Controls Adjust the dial (Figure 7) to match your weight (kg or lb). Fore/Aft Locking Lever Use the fore/aft adjustment lever to change the forward/rearward position of the seat. • Model No. 31980: Move the lever to the left (Figure 5), move the seat to a comfortable position, and release the locking lever to secure the position of the seat. • Model No.
PAGE 5
Notes:
PAGE 6
Notes:
PAGE 7
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
PAGE 8
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered Parts The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).