Installation Instructions

ManualsBrandsToro ManualsAttachmentsLED Work Light Kit, Groundsmaster 3200 or 3300 Series Traction Unit with Cab

FormNo.3435-529RevA

LEDWorkLightKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31993

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Worklight4

Worklightmount4

Hex-headscrew4

Washer8

Lockwasher4

Nut4

Prepareforinstallation.

Worklightwireharness1

Worklightassembly4

Installtheworklights.

PreparingforInstallation

Partsneededforthisprocedure:

4Worklight

4Worklightmount

4Hex-headscrew

8Washer

4Lockwasher

4Nut

Procedure

Important:Thiskitrequirestheinstallationof

acabandeitheraRoadLightKitortheLight

AdapterKitbeforeinstallingtheLEDWorkLight

Kit.ContactyourauthorizedTorodistributorfor

moreinformation.

Note:Retainallremovedpartsforlaterinstallation

unlessotherwisenoted.

1.Parkthemachineonalevelsurface,lowerthe

attachment,shutofftheengine,engagethe

parkingbrake,andremovethekey.

2.Disconnectthenegative(-)batterycable

fromthebattery;refertotheelectricalsystem

maintenancesectionofthetractionunit

Operator’sManual.

3.RemovethecabroofasshowninFigure1.

g302035

Figure1

1.Bolt

3.Cabroof

2.Washer

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3435-529*A

Summary of content (4 pages)

PAGE 1
Form No. 3435-529 Rev A LED Work Light Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31993 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Work light Work light mount Hex-head screw Washer Lock washer Nut Work light wire harness Work light assembly 1 4 4 4 8 4 4 1 4 4 Work light 4 Work light mount 4 Hex-head screw 8 Washer 4 Lock washer 4 Nut Prepare for installation.
PAGE 2
4. Remove the small mounting brackets from the work lights Figure 2. 2 Note: You may discard the small mounting brackets. Installing the Work Lights Parts needed for this procedure: 1 Work light wire harness 4 Work light assembly Procedure 1. On top of the cab, locate the loose 2-pin socket on the cab wire harness and connect the work light harness power connector (Figure 4). g304596 Figure 2 1. Small mounting bracket 5. Assemble the work lights as shown in Figure 3. g303391 Figure 4 1.
PAGE 3
4. Connect the work light assemblies and retainer brackets to the front of the machine as shown in Figure 7 using the screws and retainer brackets removed in step 3. g303416 g303440 Figure 7 1. Screw 2. Work light assembly 5. 3. Install a work light assembly in each retainer bracket location. 4. Retainer bracket Remove the retainer brackets from the top of the rear windshield (Figure 8). g303427 Figure 5 1. Work light harness 3. 2. Route the rear connectors through these holes.
PAGE 4
6. Operation Connect the work light assemblies and retainer brackets to the rear of the machine as shown in Figure 7 using the screws and retainer brackets removed in step 5. Using the Lights To illuminate the work lights, press the light switch on the steering column switch mount; refer to your Road Light Kit or Light Adapter Kit Installation Instructions. g304598 Figure 9 1. Retainer bracket 2. Work light assembly 7. 3. Screw Connect the work light connectors to the work lights (Figure 10).