Installation Instructions

ManualsBrandsToro ManualsRiding ProductsLED Beacon Kit, Groundsmaster 3200 or 3300 Series Traction Unit

FormNo.3436-176RevB

LEDBeaconKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.31996

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Prepareforinstallation.

Beaconwireharness1

Beaconmount1

Beaconsocket1

Beaconlight1

Bolt(5/16x1inch)

Nut(5/16inch)—formachineswithout

acab

Lightswitch1

Installthebeacon.

PreparingforInstallation

NoPartsRequired

Procedure

Important:ThiskitrequirestheinstallationofaRoadLightKit,anAccessoryControlKit,oraROPS

WorkLightkitbeforetheBeaconKitcanbeinstalled.ContactyourauthorizedTorodistributorfor

moreinformation.

Note:Retainallremovedpartsforlaterinstallationunlessotherwisenoted.

1.Parkthemachineonalevelsurface,lowertheattachment,shutofftheengine,engagetheparking

brake,andremovethekey.

2.Disconnectthenegative(-)batterycablefromthebattery;refertotheelectricalsystemmaintenance

sectionofthetractionunitOperator’sManual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-176*

Summary of content (8 pages)

PAGE 1
Form No. 3436-176 Rev B LED Beacon Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 31996 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – 2 Beacon wire harness Beacon mount Beacon socket Beacon light Bolt (5/16 x 1 inch) Nut (5/16 inch)— for machines without a cab Light switch 1 1 1 1 2 Prepare for installation. Install the beacon.
PAGE 2
Installing the Beacon Parts needed for this procedure: 1 Beacon wire harness 1 Beacon mount 1 Beacon socket 1 Beacon light 2 Bolt (5/16 x 1 inch) 1 Nut (5/16 inch)— for machines without a cab 1 Light switch g306876 For Machines with a Cab 1. Figure 2 Remove the cab roof as shown in Figure 1. 1. 2-pin socket 3. 2. Beacon harness power connector Route the beacon harness and connectors as shown in Figure 3. g302035 Figure 1 1. Bolt 2. Washer 2. 3.
PAGE 3
4. Remove the 2 screws behind the left door of the cab as shown in Figure 4. 8. Note: You may discard these screws. Assemble the beacon to the bracket as shown in Figure 6. Note: Ensure that the assembly is secure by tightening the wing nut on the beacon and the jam nuts on the socket once assembled. g306903 Figure 4 1. Remove these screws. 5. Install the beacon bracket to the cab (Figure 6). 6. Pull the beacon harness up through the bottom of the hole in the beacon mount. 7.
PAGE 4
For Machines with a ROPS 1. Remove the rear nuts and bolts from the work light bracket as shown in Figure 9. g307013 Figure 9 1. Nut g306946 2. Figure 7 1. Control cover 2. Bolt Assemble the beacon to the bracket and install the beacon assembly as shown in Figure 10. 2. Hex-socket head screw 10. Remove the hole plug and install the beacon switch with the raised end facing up (Figure 8). 11. Connect the beacon connector to the switch (Figure 8).
PAGE 5
4. Connect the loose work light harness connectors to the spades in the beacon socket (Figure 11). Note: The beacon connector can be threaded out of the beacon socket for connection (Figure 12). • Connect the red wire to the center beacon spade. • Connect the black wire to the outer beacon spade. g306902 g307744 Figure 11 1. Beacon socket Figure 12 3. Work light harness connectors 2. Beacon spade (2) 5. Assemble the beacon to the bracket as shown in Figure 12. 1. Beacon light 5.
PAGE 6
Operation Controls Beacon Switch Press the beacon switch to the ON position to activate the beacon.
PAGE 7
Notes:
PAGE 8
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 31996 Serial No.