HY13-1525-M1/US TGK Motor Service Procedure Effective: April 2015 Low Speed High Torque Hydraulic Motors
HY13-1525-M1/US Low Speed High Torque, Hydraulic Motors TGK Series WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise.
HY13-1525-M1/US Contents Low Speed High Torque, Hydraulic Motors TGK Series Definitions.............................................................................................................3 Design Features....................................................................................................4 Introduction...........................................................................................................5 Troubleshooting Guide....................................................
Low Speed High Torque, Hydraulic Motors Low Series Speed High Torque, Hydraulic Motors TGK TK Series HY13-1525-M1/US HY13-1518-M1/US Torqmotor Design Features Torqmotor Design Features COUPLING SHAFT HIGH PRESSURE SEAL HOUSING HEAVY DUTY DRIVE LINK TOOTH SPLINE DIRT & WATER SEAL HEAVY DUTY BEARING HIGH SPEED COMMUTATOR MATCHED ROTOR SET TGK Series features include: • The roller vane rotor set design offers low-friction and wear compensation which maximizes the useful performance life of the motor.
HY13-1525-M1/US Introduction Low Speed High Torque, Hydraulic Motors TGK Series Introduction This service manual has one purpose: to guide you in maintaining, troubleshooting and servicing the TGK Torqmotor (low speed, high torque hydraulic motor). A page the with exploded assembly view is provided several places in this manual.
HY13-1525-M1/US Troubleshooting Guide Low Speed High Torque, Hydraulic Motors TGK Series Troubleshooting Guide NOTE Hydraulic Components Before troubleshooting any system problem, check service literature published by the equipment and/or component manufacturers. Follow their instructions, if given, for checking any component other than the Torqmotor unit. If you think the problem is caused by a hydraulic component, start by checking the easy-to-reach items.
Low Speed High Torque, Hydraulic Motors Low TGKSpeed SeriesHigh Torque, Hydraulic Motors TK Series HY13-1525-M1/US HY13-1518-M1/US Troubleshooting Checklist Troubleshooting Checklist Trouble Cause Remedy Oil Leakage 1. Hose fittings loose, worn or damaged. Check & replace damaged fittings or “O” Rings. Torque to manufacturers specifications. 2.Oil seal rings (5) deteriorated by excess heat. Replace oil seal rings by disassembling Torqmotor unit. 3.
HY13-1525-M1/US Tools & Materials Required for Servicing Low Speed High Torque, Hydraulic Motors TGK Series Tools and Materials Required for Servicing • Clean, petroleum-based solvent • Emery paper • Vice with soft jaws CAUTION Mixing greases that have different bases can be detrimental to bearing life.
Low Speed High Torque, Hydraulic Motors TGK SeriesHigh Torque, Hydraulic Motors Low Speed TK Series HY13-1525-M1/US Technical Information HY13-1518-M1/US Technical Information INCHES .020 .021 .029 .030 .111 .119 .152 .160 .296 .304 .460 .470 .500 .585 .595 .660 .675 1.058 CONVERSIONS mm .51 .53 .74 .76 2.81 3.02 3.86 4.06 7.52 7.72 11.68 11.94 12.70 14.86 15.11 16.76 17.15 26.87 INCHES 1.060 1.295 1.297 1.396 1.398 1.620 1.622 1.983 1.985 2.120 2.122 2.233 2.235 2.483 2.485 2.500 2.
Low Speed High Torque, Hydraulic Motors TGK Series HY13-1525-M1/US Exploded View Typical Assembly 28 TORQUE TO 50±5 lbf·ft [68±7 N·m] (7 BOLTS) 9 33 30 31 29a 3 10 11 29b 1 12 22 32 18 17 16 14 15 14 13 2 4 23 3 5 21 20 25 3 19 6 24 3 MATCHED SET 7 3 8 MATCHED SET REAR PORT OPTION COMPONENTS RELIEF VALVE END COVER 27 5 26 4 25 SHUTTLE VALVE END COVER ASSEMBLE COMMUTATOR SEAL WITH WEDGE SIDE DOWN INTO COMMUTATOR FACE Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Des
Low Speed High Torque, Hydraulic Motors TGK Series HY13-1525-M1/US Service Parts List Chart Use Example: TGK0240US080AAAB Torqmotor includes part numbers listed to the right of TGK (SERIES), 0240 (DISP.), U (MOUNTING), S (PORTING), 08 (SHAFT), 0 (ROTATION), and AAAB (OPTION) shown in the left hand column of the chart. Caution: The charted component service information is for the Torqmotors listed only.
Low Speed High Torque, Hydraulic Motors TGK Series HY13-1525-M1/US Service Parts List SHAFT CODE EXPLODED VIEW ITEM# 12 28 COUPLING DESCRIPTION SHAFT KEY 01 - Long 6B Spline, Groove 05- 14 Tooth Spline (12/24 P), 5/8 Tap 08- 1.25" Tapered, 1-20 Thread 19 - 1.38" Tapered, 1.125-18 Thread 44 - 14 Tooth Spline (12/24 P), Groove, 12mm Tap 45 - 1.
HY13-1525-M1/US HY13-1518-M1/US Disassembly and Inspection High Torque, Torque, Hydraulic Motors Motors Low Speed High TGKSeries Series TK Preparation Before Disassembly • Before you disassemble the Torqmotor unit or any of its components read this entire manual. It provides important information on parts and procedures you will need to know to service the Torqmotor.
HY13-1525-M1/US Disassembly and Inspection Low Speed High Torque, Hydraulic Motors TGK Series Place Torqmotor in a vise 1. Place the Torqmotor in a soft jawed vise or similar support, with coupling shaft (12) pointed down and the vise jaws clamping firmly on the sides of the housing (19) mounting flange. SEE FIGURE 1. WARNING WARNING IF THE TORQMOTOR IS NOT FIRMLY HELD IN THE VISE, IT COULD BE DISLODGED DURING THE SERVICE PROCEDURES, CAUSING INJURY. Scribe alignment mark Figure 1 2.
HY13-1525-M1/US Disassembly and Inspection Remove end cover Low Speed High Torque, Hydraulic Motors TGK Series 4. Remove end cover (2). SEE FIGURE 5. Figure 5 Wash & inspect end cover 5. Thoroughly wash end cover (2) in proper solvent and blow dry. Be sure the end cover flow areas are free of contamination. Inspect end cover for cracks and the bolt head recesses for damage. Replace end cover as necessary. SEE FIGURE 6.
HY13-1525-M1/US Disassembly and Inspection Low Speed High Torque, Hydraulic Motors TGK Series Remove manifold 7. Remove manifold (6) and inspect for cracks surface scoring, brinelling or spalling. Replace manifold if any of these conditions exist. SEE FIGURE 9. A polished pattern on the ground surface from commutator or rotor rotation is normal. Remove and discard the seal ring (3).
HY13-1525-M1/US Disassembly and Inspection Low Speed High Torque, Hydraulic Motors TGK Series NOTE Series TGK Torqmotor may have a rotor set with two stator halves with a seal ring (3) between them. Discard seal ring only if stator halves become disassembled during the service procedures. NOTE A polished pattern on the wear plate from rotor rotation is normal. Check rotor vane clearance 9.
HY13-1525-M1/US Disassembly and Inspection Remove thrust bearing Low Speed High Torque, Hydraulic Motors TGK Series 12. Remove rear thrust bearing (11) and retaining bearing washer (10) from top of coupling shaft (12). Inspect for wear, brinelling, corrosion and a full complement of retained rollers. SEE FIGURE 16. Figure 16 Check coupling shaft for rust or corrosion Remove & inspect coupling shaft 12.
HY13-1525-M1/US Disassembly and Inspection Remove shaft seal, backup washer and backup ring Low Speed High Torque, Hydraulic Motors TGK Series 15. Remove shaft seal (16), backup washer (17), and backup ring (18) from TGK Series Torqmotor housing. Discard shaft seal and washers. SEE FIGURE 20. Figure 20 Remove dirt & water seal 16. Remove housing (19) from vise, invert it and remove and discard dirt and water seal (21). A blind hole bearing or seal puller is required.
HY13-1525-M1/US Disassembly and Inspection Inspect housing bearings Low Speed High Torque, Hydraulic Motors TGK Series 18. If the housing (19) assembly has passed inspection to this point, inspect the housing bearings (20) and (13) and since they are captured in the housing cavity, the two thrust washers (14) and thrust bearing (15). The bearing rollers must be firmly retained in the bearing cages, but must rotate and orbit freely. All rollers and thrust washers must be free of brinelling and corrosion.
HY13-1525-M1/US Torqmotor Assembly Low Speed High Torque, Hydraulic Motors TGK Series • Replace all seals and seal rings with new ones each time you reassemble the Torqmotor unit. Lubricate seals and seal rings with clean recommended grease, Parker Gear grease specification #045236, E/M Lubricant #K70M or Mobil Mobilith SHC® 460. A packet of grease (P/N 406018) is included in each seal kit. • NOTE: Complete seal kits are available. SEE FIGURE 25.
HY13-1525-M1/US Torqmotor Assembly Press in outer bearing Low Speed High Torque, Hydraulic Motors TGK Series 2. If the housing (19) bearing components were removed for replacement, thoroughly coat and pack a new outer bearing (20) with clean corrosion resistant grease recommended in the material section. Press the new bearing into the counterbore at the mounting flange end of the housing, using the appropriate sized bearing mandrel such as described in figure 1 which will control the bearing depth to .
HY13-1525-M1/US Torqmotor Assembly Press in dirt & water seal Low Speed High Torque, Hydraulic Motors TGK Series 3. Press a new dirt and water seal (21) into the housing (19) outer bearing counterbore. The dirt and water seal (21) must be pressed in with the lip facing out and until the seal is flush to .020 inches (.51 mm) below the end of housing. SEE FIGURE 28. Figure 28 Place housing assembly into vise 4.
HY13-1525-M1/US Torqmotor Assembly Low Speed High Torque, Hydraulic Motors TGK Series Assemble thrust washers 6. Assemble a thrust washer (14), thrust and thrust bearing bearing (15) and a second thrust washer (14) in that order. SEE FIGURE 33. CAUTION Apply masking tape to shaft Be sure the thrust bearing package is seated in the correct order after assembly of the new shaft seal and new backup washer and backup ring. Figure 33 7.
HY13-1525-M1/US Torqmotor Assembly Install thrust bearing and retaining washer Low Speed High Torque, Hydraulic Motors TGK Series 9. Install thrust bearing (11) and retaining washer (10) onto the end of coupling shaft (12). SEE FIGURE 36. Figure 36 Insert seal ring 10. Install a new seal ring (3) into the housing (19) seal ring groove. SEE FIGURE 37. Figure 37 Assemble wear plate and seal ring 11. Assemble wear plate (8) onto the housing (19). SEE FIGURE 38.
HY13-1525-M1/US Torqmotor Assembly Low Speed High Torque, Hydraulic Motors TGK Series Install drive link 12. Install drive link (9) with the long splined end down into the coupling shaft (12) and engage the drive link splines into mesh with the coupling shaft splines. SEE FIGURE 39. NOTE Use any alignment marks put on the coupling shaft and drive link before disassembly to assemble the drive link splines in their original position in the mating coupling shaft splines.
HY13-1525-M1/US Torqmotor Assembly Low Speed High Torque, Hydraulic Motors TGK Series NOTE The manifold (6) is made up of several plates bonded together permanently to form an integral component. The manifold surface that must contact the rotor set has it’s series of irregular shaped cavities on the largest circumference or circle around the inside diameter. The polished impression left on the manifold by the rotor set is another indication of which surface must contact the rotor set.
HY13-1525-M1/US Torqmotor Assembly Assemble end cover Low Speed High Torque, Hydraulic Motors TGK Series 19. Assemble end cover (2) over the commutator and in line with the alignment marks on the exterior of the motor. SEE FIGURE 46. Figure 46 Assemble cover bolts 20. Insert the bolts through the end cover until threads of each bolt reach the proper threaded hole of the housing. Hand start each bolt.
Low Speed High Torque, Hydraulic Motors TGK Series HY13-1525-M1/US Final Checks Final Checks • Pressurize the Torqmotor with 100 PSI dry air or nitrogen and submerge in solvent to check for external leaks. Make sure to plug the remaining ports prior to submerging. • Check Torqmotor for rotation. Torque required to rotate coupling shaft should not be more than 50 lb/ft (68 N m).
HY13-1525-M1/US Low Speed High Torque, Hydraulic Motors TGK Series System Maintenance Tips • Adjust fluid level in reservoir as necessary. • Encourage all operators to report any malfunction or accident that may have damaged the hydraulic system or component. • Do not attempt to weld any broken Torqmotor component. Replace the component with original equipment only. • Do not cold straighten, hot straighten, or bend any Torqmotor part.
HY13-1525-M1/US Notes Low Speed High Torque, Hydraulic Motors TGK Series 31 Parker Hannifin Corporation Hydraulic Pump/Motor Division Greeneville, Tennessee USA
Parker Hannifin Corporation Hydraulic Pump/Motor Division 2745 Snapps Ferry Road Greeneville, TN 37745 USA Tel. (423) 639-8151 FAX (423) 787-2418 www.parker.