Operator's Manual

ManualsBrandsToro ManualsGas Snow BlowersPower Max 826 OXE 26 in. 252cc Two-Stage Electric Start Gas Snow Blower

FormNo.3423-315RevB

PowerMax

824OEand826OXESnowthrower

ModelNo.37798—SerialNo.400000000andUp

ModelNo.37799—SerialNo.400000000andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedprimarilyforremoving

snowfrompavedsurfaces,suchasdrivewaysand

sidewalks,andothersurfacesfortrafconresidential

orcommercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

YoumaycontactT orodirectlyatwww.Toro.com

forproductsafetyandoperationtrainingmaterials,

accessoryinformation,helpndingadealer,orto

registeryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyoursmartphoneortablet,scan

theQRcodeontheserialnumberdecaltoaccess

warranty,parts,andotherproductinformation.

g219962

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

Important:Ifyouareusingthismachineabove

1500m(5,000ft)foracontinuousperiod,ensure

thattheHighAltitudeKithasbeeninstalled

sothattheenginemeetsCARB/EPAemission

regulations.TheHighAltitudeKitincreases

engineperformancewhilepreventingspark-plug

fouling,hardstarting,andincreasedemissions.

Onceyouhaveinstalledthekit,attachthe

high-altitudelabelnexttotheserialdecalonthe

machine.ContactanyAuthorizedToroService

DealertoobtaintheproperHighAltitudeKitand

high-altitudelabelforyourmachine.Tolocate

adealerconvenienttoyou,accessourwebsite

atwww.Toro.comorcontactourToroCustomer

CareDepartmentatthenumber(s)listedinyour

EmissionControlWarrantyStatement.Remove

thekitfromtheengineandrestoretheengineto

itsoriginalfactorycongurationwhenrunningthe

engineunder1500m(5,000ft).Donotoperatean

enginethathasbeenconvertedforhigh-altitude

useatloweraltitudes;otherwise,youcould

overheatanddamagetheengine.

Ifyouareunsurewhetherornotyourmachinehas

beenconvertedforhigh-altitudeuse,lookforthe

followinglabel(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3423-315*B

Summary of content (28 pages)

PAGE 1
Form No. 3423-315 Rev B Power Max® 824 OE and 826 OXE Snowthrower Model No. 37798—Serial No. 400000000 and Up Model No. 37799—Serial No. 400000000 and Up Operator's Manual Introduction This machine is intended to be used by residential homeowners. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties. It is not designed for removing materials other than snow.
PAGE 2
Operating the Auger/Impeller Drive................... 15 Operating the Quick Stick®............................... 15 Clearing a Clogged Discharge Chute ................ 16 Operating Tips ................................................. 17 After Operation .................................................... 17 After Operation Safety ...................................... 17 Preventing Freeze-up after Use ........................ 17 Maintenance ...........................................................
PAGE 3
• Keep clear of any discharge opening. Keep bystanders, especially small children, out of the operating area. • Never allow children to operate the machine. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. 1 2 x3 3 4 5 120-9805 decal120-9805 120-9805 1. Insert the key. 2. Prime the engine 3 times. 3. Engage the choke. 4. Pull the starter cord. 5.
PAGE 4
decal133-8061 133-8061 decal137-6198 137-6198 1. Cutting/dismemberment hazard of the fingers or hand, impeller—do not place your hand in the chute. 2. Warning—shut off the engine before using the tool to clear the chute. decal121-1240 121-1240 Order Part No. 138-8487 1. Traction drive—squeeze the lever to engage; release the lever to disengage. 4.
PAGE 5
Setup 1 Installing the Upper Handle No Parts Required Procedure g252379 2 Installing the Chute No Parts Required Procedure g252568 5
PAGE 6
3 Installing the Traction-Control Linkage No Parts Required Procedure g252391 6
PAGE 7
4 Installing the Chute-Control Rod No Parts Required Procedure g257848 7
PAGE 8
5 Installing the Snow-Cleanout Tool No Parts Required Procedure g252394 6 Checking the Engine-Oil Level No Parts Required Procedure Note: Your machine comes with oil in the engine crankcase. Before starting the engine, check the oil level and add oil if necessary. Refer to Checking the Engine-Oil Level (page 19).
PAGE 9
7 Checking the Tire Pressure No Parts Required Procedure g252396 8 9 Checking the Skids and Scraper Checking the Operation of the Traction Drive No Parts Required No Parts Required Procedure Procedure Refer to Checking and Adjusting the Skids and Scraper (page 19). CAUTION If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage.
PAGE 10
Product Overview g001011 Figure 10 The machine should move rearward. If the machine does not move or moves forward, complete the following: A. Release the traction lever and shut off the engine. B. Disconnect the trunnion from the speed-selector lever. C. Turn the trunnion downward (clockwise) on the speed-control rod. D. Connect the trunnion to the speed-selector lever. 4. Release the traction lever. 5. Move the speed selector to Position 1; refer to Operating the Speed Selector (page 15).
PAGE 11
Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety g016500 Figure 12 General Safety 1. Primer 2. Ignition switch 5. Throttle 6. Oil-drain plug 3. Choke 4. Fuel-shutoff valve 7. Recoil-start handle • For electric-start models only: Use extension cords and receptacles as specified in the manual. Inspect the electrical cord before plugging it into a power source. If the cord is damaged, replace it.
PAGE 12
Filling the Fuel Tank During Operation • For best results, use only clean, fresh (less than 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). During Operation Safety • Shut off the engine before unclogging the • Oxygenated fuel with up to 10% ethanol or 15% MTBE by volume is acceptable. • Do not use ethanol blends of gasoline (such • as E15 or E85) with more than 10% ethanol by volume.
PAGE 13
when making any repairs, adjustments, or inspections. • Never operate the machine at high transport speeds on slippery surfaces. Starting the Engine Electric-Start Model Note: To use the electric starter (electric-start models only), connect a power cord to the plug-in first and then to a power outlet. Use only a UL-listed, 16-gauge extension cord recommended for outdoor use that is not longer than 50 ft (15 m). WARNING The electrical cord can become damaged, causing a shock or fire.
PAGE 14
Standard Model g254928 Figure 16 Shutting Off the Engine g252411 Figure 17 Operating the Traction Drive 1. To engage the traction drive, squeeze the left (traction) lever to the handgrip (Figure 18). CAUTION If the traction drive is not properly adjusted, the machine may move in the direction opposite of what you intended, causing injury and/or property damage.
PAGE 15
Operating the Speed Selector WARNING If the auger and impeller continue to rotate when you release the auger/impeller lever, you could seriously injure yourself or others. The speed selector has 6 forward and 2 reverse gears. To change speeds, release the traction lever and shift the speed-selector lever to the desired position (Figure 19). The lever locks in a notch at each speed selection. Do not operate the machine. Take it to an Authorized Service Dealer for service.
PAGE 16
Clearing a Clogged Discharge Chute • If the chute does not move, refer to Adjusting the Discharge-Chute Latch (page 24). • If the chute does not turn as far to the left as it does to the right, ensure that the cable is routed to the inside of the handles. Refer to 1 Installing the Upper Handle (page 5). WARNING If the auger/impeller is running but there is no snow coming out of the discharge chute, the discharge chute may be clogged.
PAGE 17
Operating Tips After Operation DANGER After Operation Safety When the machine is in operation, the impeller and auger rotate and can injure or amputate hands or feet. • Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing the machine in any enclosure.
PAGE 18
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Inspect the traction cable and adjust it if necessary. • Inspect the auger/impeller cable and adjust it if necessary. After the first 5 hours • Change the engine oil. Before each use or daily Every 100 hours Yearly Yearly or before storage • Check the engine-oil level and add oil if necessary. • Replace the spark plug.
PAGE 19
Checking the Engine-Oil Level Service Interval: Before each use or daily—Check the engine-oil level and add oil if necessary. g252395 Checking and Adjusting the Skids and Scraper Important: The auger blades must be supported above the ground by the skids. 3. Service Interval: Yearly—Check the skids and the scraper and adjust them if necessary. Ensure that the scraper is 3 mm (1/8 inch) above and parallel to a level surface.
PAGE 20
Checking and Adjusting the Traction Cable Service Interval: After the first 2 hours—Inspect the traction cable and adjust it if necessary. Yearly—Inspect the traction cable and adjust or replace it if necessary. If the machine does not drive in the forward or reverse speeds or it drives when you release the traction lever, adjust the traction cable. If the left (traction) cable is not properly adjusted, do the following steps: 1. Loosen the jam nut. 2.
PAGE 21
Checking and Adjusting the Checking the Auger-Gearbox-Oil Level Auger/Impeller Cable Service Interval: Yearly—Check the auger-gearbox oil and add oil if necessary. Service Interval: After the first 2 hours—Inspect the auger/impeller cable and adjust it if necessary. Yearly—Inspect the auger/impeller cable and adjust or replace it if necessary. 1. Loosen the jam nut. 2. Engage the auger/impeller lever and hold it in place (Figure 28). 1. Move the machine to a level surface. 2.
PAGE 22
Changing the Engine Oil Lubricating the Hex Shaft Service Interval: After the first 5 hours—Change the engine oil. Service Interval: Yearly—Lubricate the hex shaft. Lightly lubricate the hex shaft yearly with automotive engine oil (Figure 33). Yearly—Change the engine oil. If possible, run the engine for a few minutes before changing the oil because warm oil flows better and carries more contaminants. Engine oil capacity 0.70 L (24 fl oz) Oil viscosity Refer to Figure 31.
PAGE 23
9. Install the back cover and return the machine to the operating position. 4. Set the gap between the electrodes on a new spark plug at 0.76 mm (0.030 inch) as shown in Figure 37. Replacing the Spark Plug Service Interval: Every 100 hours—Replace the spark plug. WARNING Replacing the spark plug while the engine is hot can result in burns. g001029 Figure 37 1. 0.76 mm (0.030 inch) Wait until the engine is cool to replace the spark plug. 5.
PAGE 24
Adjusting the Discharge-Chute Latch If the discharge chute does not lock into the desired position or does not unlock so that you can move it to another position, adjust the discharge-chute latch. 1. Loosen the clamp fastener on the chute-support plate until the cable is free. g019021 Figure 38 1. Cable conduit 3. Clamp fastener 2. Cable clamp 2. Remove any slack in the cable by pulling the cable conduit rearward. 3. Tighten the clamp fastener while holding the cable in place.
PAGE 25
Replacing the Headlight Model 37799 only Replace the headlight assembly (Toro part number 138-0670) when needed. 1. Remove the headlight wire from the back of the headlight (A of Figure 39). 2. Remove the bolt and nut holding the headlight assembly onto the headlight bracket and then remove the old headlight assembly (B of Figure 39). 3. Secure the new headlight assembly onto the headlight bracket with the previously removed nut and bolt (C of Figure 39). 4.
PAGE 26
Troubleshooting Problem The electric starter does not turn (electric-start models only). The engine does not start or starts hard. Possible Cause 1. The power cord is disconnected at the outlet or the machine. 1. Connect the power cord to the outlet and/or the machine. 2. The power cord is worn, corroded, or damaged. 3. The power outlet is not energized. 2. Replace the power cord. 3. Have a qualified electrician energize the outlet. 1. The key is not in the ignition or is in the STOP position. 1.
PAGE 27
Problem The engine runs, but the machine discharges snow poorly or not at all. Possible Cause Corrective Action 1. The throttle is not in the FAST position when throwing snow. 1. Move the throttle to the FAST position. 2. The machine is moving too fast to clear the snow. 3. You are trying to remove too much snow per swath. 4. You are trying to remove extremely heavy or wet snow. 5. The discharge chute is plugged. 6. The auger/impeller drive belt is loose or is off the pulley. 2.
PAGE 28
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.