Form No 3322-818 Rev A CCR POWERLITEr Snowthrower Model No. 38170—200000001 and Up Model No. 38172—200000001 and Up Model No. 38182—200000001 and Up Operator’s Manual Pour obtenir gratuitement une version en français de ce manuel, écrivez à l’adresse ci-dessous. N’oubliez pas d’indiquer les numéros de modèle et de série de votre produit. The Toro Company, Attn: Parts Dept.
Contents damage. Although Toro designs and produces safe products, you are responsible for operating the product properly and safely. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Snowthrower Safety . . . . . . . . . . . . . . . . . 3 Toro Snowthrower Safety . . . . . . . . . . . . . . . . . . . 4 Safety and Instruction Decals . . . . . . . . . . . . . . . . . 5 Assembly . . . .
• Use only the power cord supplied with the snowthrower and a receptacle appropriate for use with the cord for electric starting motors. understand the contents of this manual before the motor is ever started. Pay particular attention to the safety alert symbol which means CAUTION, WARNING, OR DANGER — “personal safety instruction.” Read and understand the instruction because it has to do with safety. Failure to comply with instruction may result in personal injury.
• Never operate the snowthrower near glass enclosures, automobiles, window wells, drop-offs, etc. without proper adjustment of the snow discharge angle. Keep children and pets away. operating the snowthrower. Keep your face hands, feet, and any other part of your body or clothing away from concealed, moving, or rotating parts.
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. On Control Panel (Model 38182) (Part No. 84-5430) On Control Panel (Models 38170 and 38172) (Part No. 84-5420) On Right Side of Near Muffler (Part No. 95-1904) On Back of Chute (Model 38182) (Part No. 61-4790) Replace Discharge Chute (Part No.
Assembly Note: Determine the left and right sides of the snowthrower by standing in the normal operating position. Loose Parts DESCRIPTION QTY. Hex bolts 2 Locknuts 2 Washers 2 Discharge chute 1 Upper handle 1 Knobs 2 Oval head bolts 2 Curved washers 2 USE Installing the discharge chute Installing the handle Installing the Discharge Chute 3. Position the knobs and curved washers on the inside of the handle and tighten the knobs securely. 1.
gasoline/oil mix. Include the following emission control system(s): EM, TWC (if so equipped). Do not include any user adjustable features; no further adjustments are needed. DANGER POTENTIAL HAZARD • When fueling, under certain circumstances, a static charge can develop, igniting the gasoline. IMPORTANT: Do not use methanol, gasoline containing methanol, gasohol containing more than 10% ethanol, premium gasoline, or white gas. Using these fuels can damage the engine’s fuel system.
2 1 2 1 3 3 5 111 Figure 4 1. Add oil to small amount of gasoline 2. Install cap and shake can to mix 6 3. Add remaining amount of gasoline 4 919 Figure 5 1. 2. 3. 4. We recommend using a fuel stabilizer/conditioner for all Toro gasoline-powered products during operation and storage. A fuel stabilizer/conditioner cleans the engine during operation and prevents gum-like varnish deposits from forming in the engine during storage.
C. When the engine starts, disconnect the power cord from the snowthrower and the outlet. strike the ground. The wheels do not need to touch the ground to self-propel. The more you tilt the handle forward, the faster the snowthrower self-propels. 5. After warming up the engine, move the choke lever to the Off position. • Always overlap each swath and discharge the snow downwind whenever possible.
3 2 Note: When you unfold the handle the discharge chute, tighten all the knobs securely. 1 Figure 7 1. Discharge chute 2. Discharge chute handle 3. Handle Maintenance Recommended Maintenance Schedule Service Item Service Operation Initial At Storage Fuel tank Drain the fuel and run the engine until the fuel tank and the carburetor are dry. X Scraper Check the scraper. Replace if necessary. X Drive belt Inspect the drive belt. Replace if necessary.
Replacing the Scraper 5. Pull the idler pulley up slightly while pulling out the drive belt. Allow the pulley to gradually release when it can move past the belt (Fig. 10). Before each season, inspect the scraper for wear. If the thickness of the scraper’s bottom is less than 1/16 in. (1.6 mm), replace the scraper (Fig. 8). 6. Rotate the rotor and work the drive belt off the rotor pulley. The belt should slide easily off the drive pulley (Fig. 10). 1. Stop the engine and remove the key from the switch.
9. Install the drive belt cover and tighten the fasteners securely, but do not overtighten. .030 in. (.76 mm) Replacing the Spark Plug m-3215 Before each season, check the spark plug. If the electrodes in the center of the plug are dark or have deteriorated, install a new NGK BPMR4A spark plug. 1. Remove the two screws that secure the control panel to the housing (Fig. 12). 6. Push the wire onto the spark plug. 7. Install the control panel with the screws.
Install the rotor blades with the thick layer on the inside of the curve. (Fig. 15). If you do not install the blades properly, the blades may be out of balance and cause the snowthrower to “hop” or “bounce.” 5. Curve the blade and secure it with the remaining four torx screws and locknuts, positioning the screw heads on the thick layer side of the blade (Fig. 15). 6. Tighten all screws and nuts securely. 2. Insert the new blade between the blade supports. 7.
Tightening the Fasteners and Cleaning the Snowthrower 1. Tighten all loose screws, bolts, and locknuts. Repair or replace damaged parts. 2. Clean the snowthrower thoroughly. Covering and Storing the Snowthrower Cover the snowthrower and store it in a clean, dry place out of the reach of children. WARNING POTENTIAL HAZARD • Gasoline is highly flammable, explosive, and dangerous if inhaled. WHAT CAN HAPPEN • If gasoline contacts a flame or is inhaled, serious personal injury can occur.
Gas Powered Snow Products The Toro Total Coverage Guarantee A Full Two-Year Warranty (Limited Warranty for Commercial Use) What Is Covered By This Express Warranty? What Does This Warranty Not Cover? and How Does Your State Law Relate To This Warranty? The Toro Company promises to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship for a period of two years from the date of purchase.
