MODEL NO. ‘\ THRU & UP MODEL NO. THRU & UP FORM NO. 3313-883 Rev. C OPERATOR’S MANUAL CCR 2000~ SNOW THROWER J SAFETY INSTRUCTIONS v ¥ slut in personal injury. To assure maximum safety, best performance, and fo grin knowledge of the product, it ig segment. manual before the motor is aver started. Pay particular attention to the safety alert symbol which means CAUTION, WARNING OR DANGER — “personal safety instruction.” Read and understand the instruction because it has to do with safety.
A\ SAFETY INSTRUCTIONS 18. Never clear snow off steps slopes or across the faces of slopes. Exercise extreme caution when changing direction on slopes. 17. Do not overload the snow thrower by clearing snow at too fast a rate. 18. Use extra ma caution when crossing or operating snow thrower on walks, roads, or gravel ar crushed rock drives. Refer to Operating Instructions, page 7, item 4 for correct operating procedure. 19.
A\ SAFETY SYMBOL GLOSSARY \ Hake H_> o Stop engine to adjust, unclog, or remove debris 110 volt tartar Recoil starter ignition ignition off on o 50:1 ratio unleaded gasoline to 2-cycle olf TABLE OF CONTENTS Assembly Instructions Be fare Operating .5 Operating Instructions 6 Maintenance 8 General Maintenance Adjusting Control Bar , .. 8 Draining Gasoline . 8 Replacing Scraper 8 Replacing Drive Alt g Page Replacing Spark Pius . Adjusting Carburetor . Replacing Rotor Biased . Storing Snow thrower .. .
ASSEMBLY INSTRUCTIONS INSTALL CHUTE CRANK (Fig. 2) 1. Insert flattened end of chute crank through hole in shroud while aligning mounting bracket with holes in lower handle. Slowly rotate crank until flattened end fits into hidden gear opening and chute sing turns with crank. Make sure plastic bushing is tulle inserted into hole in amounting bracket, the secure mounting bracket to handle with (2) cap screws and knockouts. Figure 2 3. Gear 4. Plastic bushing 1. Chute crank 2.
ASSEMBLY INSTRUCTIONS Figure 5 1. Deadbolt 3. Rear hole 2. Control bar bracket BEFORE OPERATING A WANING engine. DANGER: Gasoline is extremely flammable and explosive under certain conditions. Do not smoke when handling fuel and keep fuel tar away from open flames and sparks. Never buy more than a 30 day supply of gasoline. Store it in an approved container. Keep gasoline out of reach of children, Refuel outdoors and only when engine is cold. Do not fill tank full.
BEFORE OPERATING Toto also recommends that Toto Stabilizer/Conditioner be used regularly in alt Toto gasoline powered products during operation and storage seasons. Toto Stabilizer/Gonditionsr cleans the engine during operation and prevents varnish deposits from forming in the engine during periods of storage. IMPORTANT: NEVER USE METHANOL, GASOLINE CONTAINING METHANOL, GASOHOL CONTAINING MORE THAN 10% ETHANOL, PREMIUM GASOLINE, OR WHITE GAS BECAUSE ENGINE FUEL SYSTEM DAMAGE COULD RESULT.
OPERATING INSTRUCTIONS IMPORTANT: Excessive running of the electric starter could damage the starter due to overheating. To prevent possible damage, do not run electric starter more than 10 times at intervals of § seconds ON, § seconds OFF. Then wait more than 40 minutes to allow starter to cool before continuing to run starter. Before repeating engine starting procedure, check that ignition key switch is ON, and make sure there is fresh fuel in fiat tank.
MAINTENANCE GENERAL MAINTENANCE Normally, the only maintenance required is cleaning the unit and tightening nuts, bolts, and screws. Howard, the scraper, drive belt, rotor biased, and spark plug should be checked once a year. ADJUSTING CONTROL BAR (Fig. 8-10) Periodically check control bar for proper adjustment. 1. Turn ignition key to OFF, 2. CHECK ADJUSTMENT (Fig. control bar back toward handle until slack in celeb is removed.
MAINTENANCE 1/18 Figure 11 1. Se raper 4. Remove (3} carriage bolts and lockouts hooding scraper in place (Fig. 12). Remove scraper by sliding it to right and down. 8. Install new scraper 1o housing with carriage bolts and nuts. 2. Remove (3) self tapping screws, (2) cap screws, {1} washer and {2) nuts securing bat cover to snow thrower frame (Fig. 13}, Set belt cover aside. Figure 13 1. Cap screw, nut 3. Long lest tapping 2. Cap screw, nut, screw washer 4. Short self tapping resews 3. REMOVING BELT (Fig.
MAINTENANCE REPLACING SPARK PLUG (Fig. 15-17) Before each snow season, check the spark plug. It electrodes in center of plug are dark or have deteriorated, install a new plug. Use an NGK BPM spark plug and set gap at .032” (.81 mmj. 1. REMOVE CONTROL PANEL {Fig. {3} cap screws securing control panel to housing. Remove ignition key and lift off panel, allowing it to hang on recoil tops. onto spark plug and reinstall control panel with (3} cap screws. c.032” {0813 mm) Figure 15 1. Control panel 2.
MAINTENANCE Figure 19 1. Bolt 4. Lockout 2. Washer §. Thin side 3. Bushing 6. Thick side 2. Slide the blade out from between the steel plates and push the (8) bushings out of the blades holes {Fig. 19). 3. INSTALLING NEW BLADE-The rotor blades are made of laminated rubber. Examine the edge of a blade to see the difference in layer thicknesses {Fig. 19}, (Some blades have a part number on the thick side of the blade.} Both biased must be installed with the thick side facing down.
it is Toto's policy to design and produce high quality products. To ensure customer satisfaction, Toto has extensive warranty coverage on its products. Your TOR GTS Engine powered product has two warranty statements covering it. The Toto Promise is our standard warranty statement and is printed on the last page of this manual.
What Does This Warranty Not Cover? This Warranty does not cover: 1. Any repairs on products used commercially. 2. Normal maintenance including replacement of spark plugs, air filter, fuel filter, and carburetor adjustments. 3. Oil change and lubrication, » Repairs or adjustments due to! a. Failure to follow proper maintenance procedures; b. Rotary rower blade striking an object; ¢. Contaminants in the fuel system; d. improper fuse or fuel mixture (consult your owner’s manual if in doubt); e.
GUARANTEED TO START MAINTENANCE RECORD To keep the starting guarantee in effect, you must perform the following maintenance after every 25 operating hours, more often in dusty and dirty conditions. Folio tha procedures in this Operator's Manual and record information on this chart.
THE TOR TOTAL COVERAGE Products GUARANTEE A Full Warranty (Limited Warranty for Commercial Use) ‘What Is Covered By This Express Warranty? The Toto Company promises to repair any TOR Product used for residential purposes if defective in materials ar workmanship for a period of two years from the date of purchase. The cost of parts and labor are included, but the customer pays the transportation costs.