FORM NO, 3320-548 MODEL NO, & UP MODEL NO, & UP OPERATOR'S MANUAL | CCR 2000" SNOW THROWER | SAFETY INSTRUCTIONS This safety alert symbol means CAUTION — PERSONAL SAFETY INSTRUCTION. Read the instruction because it has to do with safety, Failure to comply with the instruction may resit in personal injury, The Snow thrower is designed and tested to offer safe and effective service, provided it is operated in strict accordance with the following Safety instructions.
SAFETY INSTRUCTIONS clearing snow thrower, stop engine by turning key to OFF, Always wait for all heartstrings stop, Do not make adjustments while engine is running. 19. After clearing snow, let engine run for a few minutes so moving parts do not freeze, MAINTENANCE AND STORAGE 20. REMOVE KEY FROM SWITCH when storing snow thrower. Store key in memorable place. 21. Never store snow thrower with fuel in the fuel tank inside a building whets open flame or sparks are present, Allow engine to col before storing.
ASSEMBLY INSTRUCTIONS INSTALL WHEELS (Fig. 1) 1. Slide a short spacer and a wheel onto right hand end of ate. Side of whee! with six spokes must face center of axis. Figure 1 1. Short Spacer 3. Push Nut 2 Long Spacer 2. Place 2 push nut onto end of axle and drive on using a hammer, Place 2 wood block under opposite end of axle when mounting push nut. 3. Slide a long spacer and wheel onto opposite end of axis. Side of wheel with six spokes must race center of axle, 4.
ASSEMBLY INSTRUCTIONS INSTALL CONTROL CABLE (Fig. 5} 1. Route control cable thru eye bolt and hook upper end in rear hole {hole with arrow} in control bas bracket, 2. Move control bar back toward handle until stack in cable is removed. Gap between control bar bracket and handle should be approximately if an adjustment is required, refer to Adjusting Control Bar, page 7, step 3. Figure § 1. Eye bolt 3. Rear Hole 2.
BEFORE OPERATING of reach of children, DANGER: Gasoline is extremely flammable and explosive under certain conditions. Do not smoke when handling fuel and keep fuel far away from open flames and sparks, Never buy more than a 30 day supply of gasoline and store it in an approved container. Keep gasoline out Re furl outdoors, only when engine is cold. Fill tank to within from top of filler neck, not into filler neck.
OPERATING INSTRUCTIONS STARTING/STOPPING ENGINE (Fig. 7} 1. CONTROLS~ Key switch, primer, electric start button and recoil start are located on control panel. Choke is just below control panel. Figure 7 & Alec. start button 1. Key Switch 2. Primer 8. Cord connection* 3. Recoil Start » ELEV STAT MOREL 4. Choke 2. Turn key to ON and pull choke out. 3. Cover hole in center of primer with thumb and push once. An additional prime may be necessary in extremely cold temperatures.
MAINTENANCE GENERAL MAINTENANCE Normally, the only maintenance required is cleaning the unit and tightening nuts, bolts, and screws, However, the scraper, drive belt, rotor blades and spark plug should be checked once a year, ADJUSTING CONTROL BAR {Fig. 9 & 10) Periodically check control bar for proper adjustment. 1. Turn ignition key to OFF. 2. CHECK 9) — Move control bar back toward handle until slack in cable js removed.
MAINTENANCE {1.6 mm), (See Figure 11), replace scraper, 1, Turn ignition key to OFF, 2. Drain gasoline from fuel tank: refer to Draining Gasoline, page 7. 3, Tip snow thrower up onto its nose. Remove carriage bolts and lockouts holding scraper in place (Fig. 12). Remove scraper by sliding o right and down. Figure 12 1. Scraper 2. Carriage Bolts & Lack nuts 4, install new scraper to housing with carriage obits and nuts. REPLACING DRIVE BELT {Fig. 13 & 14} Inspect drive bat before each season.
MAINTENANCE 2. REMOVE SPARK PLUG (Fig. 16) — Phil wire off spark plug and remove plug. Examine the plug and replace if cracked, fouled, or Note: Whenever rotor blades are replaced, scraper should also be replaced to assure groper snow thrower operation and performance. Figure 16 1. Spark Pius Wire dirty. DO NOT SANDBLAST, SCRAPE OR CLEAN SPARK PLUG BECAUSE DIRT MAY RELEASE AND FALL INTO CYLINDER CAUSING ENGINE DAMAGE. 3. INSTALL SPARK PLUG — Set air gap {Fig. 17} between electrodes at 032" {8.1 mm}.
MAINTENANCE facing down. If one blade is installed with the thicker layer facing up and the other blade installed with the thicker layer facing down, the blades wilt be unbalanced, causing the snow thrower to “hop* or “bounce.” 4, Press the (8) bushings into the holes in the new bide. 5. Insert the new blade between the steel plates. Secure it to the steel pistes with {4) 7/16" bolts snd {4} lockouts. Position bolt heads on thick {bottom) side of blade.