Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38273

FormNo.3369-503RevD

Powerlite

Snowthrower

ModelNo.38273—SerialNo.312000001andUp

ModelNo.38283—SerialNo.312000001andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeownersorprofessional,hiredoperators.It

isdesignedprimarilyforremovingsnowfrom

pavedsurfaces,suchasdrivewaysandsidewalks,

andothersurfacesfortrafconresidentialor

commercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow,norisit

designedforclearingoffgravelsurfaces.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourmachineproperlyandtoavoidinjury

andmachinedamage.Youareresponsibleforoperating

themachineproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

machineandaccessoryinformation,helpndinga

dealer,ortoregisteryourmachine.

Wheneveryouneedservice,genuineToroparts,

oradditionalinformation,contactanAuthorized

ServiceDealerorToroCustomerServiceandhave

themodelandserialnumbersofyourmachineready.

Figure1identiesthelocationofthemodelandserial

numbersonthemachine.Writethenumbersinthe

spaceprovided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjury

ordeathifyoudonotfollowtherecommended

precautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

Safety

ThismachinemeetsorexceedstheISOstandard

8437ineffectatthetimeofproduction.

Readandunderstandthecontentsofthismanual

beforeyoustarttheengine.

Thisisthesafetyalertsymbol.Itisusedtoalert

youtopotentialpersonalinjuryhazards.Obeyall

safetymessagesthatfollowthissymboltoavoid

possibleinjuryordeath.

Improperlyusingormaintainingthismachine

couldresultininjuryordeath.Toreducethis

potential,complywiththefollowingsafety

instructions.

Training

•Read,understand,andfollowallinstructionsonthe

machineandinthemanual(s)beforeoperatingthis

machine.Bethoroughlyfamiliarwiththecontrols

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (20 pages)

PAGE 1
Form No. 3369-503 Rev D Powerlite® Snowthrower Model No. 38273—Serial No. 312000001 and Up Model No. 38283—Serial No. 312000001 and Up Operator's Manual Introduction Model No. This machine is intended to be used by residential homeowners or professional, hired operators. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties.
PAGE 2
and the proper use of the machine. Know how to stop the machine and disengage the controls quickly. • Never attempt to make any adjustments while the engine is running (except when specifically recommended by manufacturer). • Never allow children to operate the machine. Never allow adults to operate the machine without proper instruction.
PAGE 3
chute, stop the engine, remove the key, and wait for all moving parts to stop. • Never operate the machine without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. • Never touch a hot engine or muffler. • Before leaving the operating position, stop the engine, remove the ignition key, and wait for all moving parts to stop.
PAGE 4
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 120-0149 1. Primer 2. Push the primer two times to prime the engine. 117-6047 Order part no. 117-7742 3. Push key in to switch engine On. 1. Cutting dismemberment, impeller and cutting dismemberment, auger hazards—do not place your hand in the chute; remove the ignition key and read the instructions before servicing or performing maintenance. 4.
PAGE 5
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 Oval-head bolts Curved washers Handle knobs 2 2 2 Install the handle. 2 No parts required – Install the recoil starter handle. 3 Discharge chute assembly Screws Washers Locknuts Knob 1 2 2 2 1 Install the discharge chute assembly. Bottle of engine oil 1 Fill the engine with oil. No parts required – Adjust the control cable.
PAGE 6
2 Installing the Recoil Starter Handle No Parts Required Figure 5 Procedure 1. Knob Install the recoil starter handle in the rope guide as shown in Figure 4. 2. Bolt (2), washer (2), and locknut (2) Note: Install the bolts from the inside of discharge chute assembly so that the washers and locknuts are on the outside of the chute. Important: Do not overtighten the locknuts. 4 Figure 4 Filling the Engine with Oil 1.
PAGE 7
oil, remove the excess oil as directed in Changing the Engine Oil. Note: You may tip the machine forward (handle up) a little to make adding oil easier. Remember to return the machine to the operating position before checking the oil level. Important: Do not tip the machine all the way forward onto its nose, or fuel may leak out of the machine. 5. Screw the oil fill cap into the oil fill hole and hand tighten it securely. Figure 6 5 1. Move the machine to a level surface. Adjusting the Control Cable 2.
PAGE 8
Product Overview Note: Ensure that a gap of 1/16 to 1/8 inch (2 to 3 mm) exists between the control bar and the handle (Figure 8). Important: The control cable must contain some slack when you disengage the control bar for the rotor blades to stop properly. Adjusting the Control Cable 1. Slide up the spring cover and unhook the spring from the adjuster link (Figure 9). Figure 10 Figure 9 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. 1. Control bar 6.
PAGE 9
Operation you may add fuel stabilizer to newly purchased gasoline to keep it fresh for up to 6 months. Note: Determine the left and right sides of the machine from the normal operating position. Checking the Engine Oil Level Service Interval: Before each use or daily—Check the engine oil level and add oil if necessary. 1. Ensure that the fuel tank is not overfilled (refer to Figure 12) and that the fuel cap is securely in place. 2. Move the machine to a level surface. 3.
PAGE 10
Starting the Engine Important: Do not tip the machine all the way forward onto its nose, or fuel may leak out of the machine. 1. Push the ignition key fully inward to the On position (Figure 15). Max fill: 12 oz. (0.35 l), type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 14 to select the best oil viscosity for the outdoor temperature range expected: Figure 15 2. Move the choke lever fully to the right (Figure 16).
PAGE 11
WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it to start the machine. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance (model 38283 only). Figure 17 Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole.
PAGE 12
Engaging the Rotor Blades To engage the rotor blades, hold the control bar against the handle (Figure 20). Figure 22 Adjusting the Discharge Chute and Chute Deflector Figure 20 1. Control bar To adjust the discharge chute, move the chute handle as shown in Figure 23. Disengaging the Rotor Blades Figure 23 1. Chute handle To disengage the rotor blades, release the control bar (Figure 21).
PAGE 13
To clear the chute: • Shut the engine off ! • Wait 10 seconds to be sure the rotor blades have stopped rotating. • Always use a clean-out tool, not your hands. when trying to operate frozen controls. If you have difficulty operating any control or part, start the engine and let it run for a few minutes. Operating Tips WARNING Self-propelling the Machine The rotor blades can throw stones, toys, and other foreign objects and cause serious personal injury to the operator or to bystanders.
PAGE 14
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour After the first 2 hours Before each use or daily Yearly Yearly or before storage Maintenance Procedure • Check the control cable and adjust it if necessary. • Check for loose fasteners and tighten them if necessary. • Change the engine oil. • Check the engine oil level and add oil if necessary.
PAGE 15
3. Place an oil drain pan under the oil drain plug (Figure 11), remove the oil drain plug, and tip the machine backward (handle down) halfway to the ground to drain the used oil into the oil drain pan. Max fill: 12 oz. (0.35 l), type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 28 to select the best oil viscosity for the outdoor temperature range expected: Important: Do not tip the machine all the way back to the ground, or fuel may leak out of the machine.
PAGE 16
until the fuel begins to drain from the carburetor. Drain the fuel into an approved fuel container. Important: Do not remove the carburetor bowl bolt on the bottom of the carburetor. Figure 29 1. Center electrode insulator 3. Air gap (not to scale) 2. Side electrode 6. Install the spark plug and torque it to 20–22 ft-lb (27–30 N-m). 7. Connect the wire to the spark plug. Storage Figure 30 Storing the Machine 1. Carburetur bowl bolt—do not remove 2. Small screw on carburetor WARNING B.
PAGE 17
Notes: 17
PAGE 18
Notes: 18
PAGE 19
International Distributor List Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip. B-Ray Corporation Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Equiver Femco S.A. G.Y.K. Company Ltd. Geomechaniki of Athens Guandong Golden Star Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Ibea S.P.A. Irriamc Irrigation Products Int'l Pvt Ltd. Jean Heybroek b.v. Lely (U.K.
PAGE 20
The Toro Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if used for residential purposes* if defective in materials or workmanship. Instructions for Obtaining Warranty Service If you think that your Toro Product contains a defect in materials or workmanship, follow this procedure: 1. Contact your seller to arrange service of the product.