Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38273

FormNo.3365-594RevB

Powerlite

Snowthrower

ModelNo.38273—SerialNo.311000001andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeownersorprofessional,hiredoperators.It

isdesignedprimarilyforremovingsnowfrom

pavedsurfaces,suchasdrivewaysandsidewalks,

andothersurfacesfortrafconresidentialor

commercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow,norisit

designedforclearingoffgravelsurfaces.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourmachineproperlyandtoavoidinjury

andmachinedamage.Youareresponsibleforoperating

themachineproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

machineandaccessoryinformation,helpndinga

dealer,ortoregisteryourmachine.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourmachineready.

Figure1

identiesthelocationofthemodelandserialnumbers

onthemachine.Writethenumbersinthespace

provided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafetyalertsymbol

(Figure2),whichsignalsahazardthatmaycauseserious

injuryordeathifyoudonotfollowtherecommended

precautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

Safety

ThismachinemeetsorexceedstheISOstandard

8437ineffectatthetimeofproduction.

Readandunderstandthecontentsofthismanual

beforeyoustarttheengine.

Thisisthesafetyalertsymbol.Itisusedtoalert

youtopotentialpersonalinjuryhazards.Obeyall

safetymessagesthatfollowthissymboltoavoid

possibleinjuryordeath.

Improperlyusingormaintainingthismachine

couldresultininjuryordeath.Toreducethis

potential,complywiththefollowingsafety

instructions.

Training

•Read,understand,andfollowallinstructionsonthe

machineandinthemanual(s)beforeoperatingthis

machine.Bethoroughlyfamiliarwiththecontrols

andtheproperuseofthemachine.Knowhowto

stopthemachineanddisengagethecontrolsquickly.

•Neverallowchildrentooperatethemachine.Never

allowadultstooperatethemachinewithoutproper

instruction.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (20 pages)

PAGE 1
Form No. 3365-594 Rev B Powerlite® Snowthrower Model No. 38273—Serial No. 311000001 and Up Operator's Manual Introduction This machine is intended to be used by residential homeowners or professional, hired operators. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties. It is not designed for removing materials other than snow, nor is it designed for clearing off gravel surfaces.
PAGE 2
• Keep the area of operation clear of all persons, particularly small children. repair to protect eyes from foreign objects that may be thrown from the machine. • Exercise caution to avoid slipping or falling. • Let the engine and machine adjust to outdoor temperatures before starting to clear the snow. Preparation Operation • Thoroughly inspect the area where the machine is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.
PAGE 3
Clearing a Clogged Discharge Chute • If a shield, safety device, or decal is damaged, illegible, or lost, repair or replace it before beginning operation. Also, tighten any loose fasteners. Hand contact with the rotating rotor blades inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. • Do not smoke while handling gasoline. • Do not use the machine on a roof.
PAGE 4
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 117-6047 Order part no. 117-7742 1. Cutting dismemberment, impeller and cutting dismemberment, auger hazards—do not place your hand in the chute; remove the ignition key and read the instructions before servicing or performing maintenance. 117-7713 1. Warning—read the Operator’s Manual. 2.
PAGE 5
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 Oval-head bolts Curved washers Handle knobs 2 2 2 Install the handle. 2 No parts required – Install the recoil starter handle. 3 Discharge chute assembly Screws Washers Locknuts Knob 1 2 2 2 1 Install the discharge chute assembly. Bottle of engine oil 1 Fill the engine with oil. No parts required – Adjust the control cable.
PAGE 6
2 Installing the Recoil Starter Handle No Parts Required Figure 5 Procedure 1. Knob Install the recoil starter handle in the rope guide as shown in Figure 4. 2. Bolt (2), washer (2), and locknut (2) Note: Install the bolts from the inside of discharge chute assembly so that the washers and locknuts are on the outside of the chute. Important: Do not overtighten the locknuts. 4 Figure 4 Filling the Engine with Oil 1.
PAGE 7
oil, remove the excess oil as directed in Changing the Engine Oil. Note: You may tip the machine forward (handle up) a little to make adding oil easier. Remember to return the machine to the operating position before checking the oil level. Important: Do not tip the machine all the way forward onto its nose, or fuel may leak out of the machine. 5. Screw the oil fill cap into the oil fill hole and hand tighten it securely. Figure 6 5 1. Move the machine to a level surface. Adjusting the Control Cable 2.
PAGE 8
Product Overview Note: Ensure that a gap of 1/16 to 1/8 inch (2 to 3 mm) exists between the control bar and the handle (Figure 8). Important: The control cable must contain some slack when you disengage the control bar for the rotor blades to stop properly. Adjusting the Control Cable 1. Slide up the spring cover and unhook the spring from the adjuster link (Figure 9). Figure 10 1. 2. 3. 4. 5. Figure 9 1. Adjuster link 2. Z-fitting 3. Spring cover 4. Unhook the spring here.
PAGE 9
Operation you may add fuel stabilizer to newly purchased gasoline to keep it fresh for up to 6 months. Note: Determine the left and right sides of the machine from the normal operating position. Checking the Engine Oil Level Service Interval: Before each use or daily—Check the engine oil level and add oil if necessary. DANGER Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can burn you and others.
PAGE 10
Starting the Engine Important: Do not tip the machine all the way forward onto its nose, or fuel may leak out of the machine. 1. Push the ignition key fully inward to the On position (Figure 15). Max fill: 12 oz. (0.35 l), type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 14 to select the best oil viscosity for the outdoor temperature range expected: Figure 15 2. Move the choke lever fully to the right (Figure 16).
PAGE 11
WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it to start the machine. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance. Figure 17 Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole. Important: Do not use the primer or the choke if the engine has been running and is hot.
PAGE 12
Engaging the Rotor Blades To engage the rotor blades, hold the control bar against the handle (Figure 20). Figure 22 Adjusting the Discharge Chute and Chute Deflector Figure 20 1. Control bar To adjust the discharge chute, move the chute handle as shown in Figure 23. Disengaging the Rotor Blades To disengage the rotor blades, release the control bar (Figure 21). Figure 23 1.
PAGE 13
Clearing a Clogged Discharge Chute • Rotate the discharge chute left and right to free it from any ice buildup. Important: Hand contact with the rotating rotor blades inside the discharge chute is the most common cause of injury associated with machine. Never use your hand to clean out the discharge chute.
PAGE 14
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour After the first 2 hours Before each use or daily Yearly Yearly or before storage Maintenance Procedure • Check the control cable and adjust it if necessary. • Check for loose fasteners and tighten them if necessary. • Change the engine oil. • Check the engine oil level and add oil if necessary.
PAGE 15
3. Place an oil drain pan under the oil drain plug (Figure 11), remove the oil drain plug, and tip the machine backward (handle down) halfway to the ground to drain the used oil into the oil drain pan. 4. 5. 6. 7. 8. Use Figure 28 to select the best oil viscosity for the outdoor temperature range expected: Important: Do not tip the machine all the way back to the ground, or fuel may leak out of the machine. After draining the used oil, return the machine to the operating position.
PAGE 16
B. Unscrew, but do not remove, the small screw on the side of the carburetor fuel bowl (Figure 30) until the fuel begins to drain from the carburetor. Drain the fuel into an approved fuel container. Important: Do not remove the carburetor bowl bolt on the bottom of the carburetor. Figure 29 1. Center electrode insulator 2. Side electrode 3. Air gap (not to scale) 6. Install the spark plug and torque it to 20–22 ft-lb (27–30 N-m). 7. Connect the wire to the spark plug.
PAGE 17
Notes: 17
PAGE 18
Notes: 18
PAGE 19
International Distributor List Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip. B-Ray Corporation Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Equiver Femco S.A. G.Y.K. Company Ltd. Geomechaniki of Athens Guandong Golden Star Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Ibea S.P.A. Irriamc Irrigation Products Int’l Pvt Ltd. Jean Heybroek b.v. Lely (U.K.
PAGE 20
The Toro Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if used for residential purposes* if defective in materials or workmanship. Instructions for Obtaining Warranty Service If you think that your Toro Product contains a defect in materials or workmanship, follow this procedure: 1. Contact your seller to arrange service of the product.