Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38284

FormNo.3405-361RevA

Powerlite

™

Snowthrower

ModelNo.38274—SerialNo.400000000andUp

ModelNo.38284—SerialNo.400000000andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedprimarilyforremoving

snowfrompavedsurfaces,suchasdrivewaysand

sidewalks,andothersurfacesfortrafconresidential

orcommercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow,norisitdesigned

forclearinggravelsurfaces.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

YoumaycontactT orodirectlyatwww.Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation.

g216757

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3405-361*A

Summary of content (20 pages)

PAGE 1
Form No. 3405-361 Rev A Powerlite™ Snowthrower Model No. 38274—Serial No. 400000000 and Up Model No. 38284—Serial No. 400000000 and Up Operator's Manual Introduction Model No. This machine is intended to be used by residential homeowners. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties.
PAGE 2
Before Operation ................................................... 7 Before Operation Safety ..................................... 7 Filling the Fuel Tank ............................................ 8 Checking the Engine-Oil Level............................ 9 During Operation ................................................... 9 During Operation Safety ..................................... 9 Starting the Engine ........................................... 10 Engaging the Rotor Blades ....................
PAGE 3
• Keep clear of any discharge opening. Keep bystanders, especially small children, out of the operating area. • Never allow children to operate the machine. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal120-0149 120-0149 1. Primer 4. Pull the key to switch the engine switch off. 117-6047 2. Push the primer 2 times to prime the engine. 5.
PAGE 4
Setup 1 Installing the Handle No Parts Required Procedure g253607 2 Installing the Discharge Chute No Parts Required Procedure g255436 4
PAGE 5
3 Installing the Recoil-Start Handle No Parts Required Procedure g253609 5
PAGE 6
4 Filling the Engine with Oil No Parts Required Procedure g253610 5 Adjusting the Control Cable No Parts Required Procedure Refer to Checking and Adjusting the Control Cable (page 15).
PAGE 7
Specifications Product Overview Model 38274 38284 Weight Length Width Height 24.5 kg (54 lb) 94 cm 48 cm 114 cm 26.3 kg (37 inches) (19 inches) (45 inches) (58 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
PAGE 8
Important: For best results, purchase only the quantity of fuel that you expect to use in 30 days. Otherwise, you may use fuel stabilizer/conditioner in the machine at all times to keep the fuel fresh longer when used as directed by the fuel-stabilizer manufacturer. beginning operation. Also, tighten any loose fasteners. • Two-stage models only: Adjust the collector housing height to clear a gravel or crushed-rock surface. Fuel Safety Fuel is extremely flammable and explosive.
PAGE 9
Checking the Engine-Oil Level Service Interval: Before each use or daily g253610 Figure 11 During Operation • When not actively clearing snow, disengage power During Operation Safety • Exercise extreme caution when operating the to the auger. machine on or crossing gravel drives (2-stage models only), walks, or roads. Stay alert for hidden hazards or traffic. • Shut off the engine before unclogging the • • • • • • • • machine and always use a stick or the snow-cleanout tool (if provided).
PAGE 10
when making any repairs, adjustments, or inspections. • Never operate the machine at high transport speeds on slippery surfaces. Starting the Engine Electric-Start Model Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole. Important: Do not use the primer or the choke if the engine has been running and is hot. Excessive priming may flood the engine and prevent it from starting.
PAGE 11
Standard Model Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole. Important: Do not use the primer or the choke if the engine has been running and is hot. Excessive priming may flood the engine and prevent it from starting. g253666 Figure 13 Engaging the Rotor Blades Disengaging the Rotor Blades To engage the rotor blades, hold the control bar against the handle (Figure 14). To disengage the rotor blades, release the control bar (Figure 15).
PAGE 12
Adjusting the Discharge Chute and Chute Deflector Shutting Off the Engine To shut off the engine, pull the ignition key outward until it clicks into the OFF position (Figure 16) or move the choke lever fully to the right (B of Figure 13). To adjust the discharge chute, move the chute handle as shown in Figure 17. g011580 Figure 17 1.
PAGE 13
Self-Propelling the Snowthrower inconspicuous location before use. These marks are not permanent. Lift the machine handle until the wheels are just off the ground and the scraper and rotor blades touch the ground. The machine propels forward (Figure 19). g011640 Figure 19 1. Wheels off the ground 2. Scraper and rotor blades in contract with the ground Note: By slightly varying lifting force on the handle, you can control the forward speed of the machine.
PAGE 14
After Operation After Operation Safety • Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing the machine in any enclosure. • When storing the machine for more than 30 days, refer to Storage (page 19) for important information. • Run the machine a few minutes after throwing snow to prevent freeze-up of the collector and impeller.
PAGE 15
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour After the first 2 hours Before each use or daily Yearly Yearly or before storage Maintenance Procedure • Check the control cable and adjust it if necessary. • Check for loose fasteners and tighten them if necessary. • Change the engine oil. • Check the engine-oil level and add oil if necessary. • Check the control cable and adjust it if necessary.
PAGE 16
Adjusting the Control Cable 1. Slide up the spring cover and unhook the spring from the adjuster link (Figure 21). g011544 Figure 22 1. The wear-indicator hole is intact; you do not need to replace the rotor blades. Changing the Engine Oil g006402 Figure 21 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. Service Interval: After the first 2 hours Yearly If possible, run the engine for a few minutes before changing the oil to warm it.
PAGE 17
9. Screw the oil-fill cap into the oil-fill hole, and tighten it securely by hand. 10. Wipe up any spilled oil. 11. Dispose of the used oil properly at a local recycling center. Servicing the Spark Plug Service Interval: Yearly—Service the spark plug and replace it if necessary. Use a Toro spark plug (Part No. 119-1961). g013824 Figure 23 1. The oil level is at its maximum. 3. The oil level is too low—add oil to the crankcase. 1. Shut off the engine and wait for all moving parts to stop. 2.
PAGE 18
Replacing the Drive Belt If drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt. 1. Remove the 4 bolts that hold the drive-belt cover (Figure 26) in place. g011642 Figure 27 1. Belt guide 2. Engine pulley Note: Do not distort or damage the belt guide. 6. To install the new drive belt, reverse the steps above.
PAGE 19
Storage Storing the Machine WARNING Fuel fumes are highly flammable, explosive, and dangerous if inhaled. If you store the product in an area with an open flame, the fuel fumes may ignite and cause an explosion. • Do not store the machine in a house (living area), basement, or any other area where ignition sources may be present, such as hot water and space heaters, clothes dryers, furnaces, and other appliances. g013829 Figure 29 1.
PAGE 20