A WARNING: 1Y The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
1. Chute crank 3. Gear 2. Mounting bracket 4. Plastic bushing {Unit shown on right side) 1. Short spacer 3. Push nut 2. Long spacer 1. Chute ring 2.
1. Add ofl to small amount of 3. Add remaining amour it of gasoline gasoline 2. install cap and shake can o mix 1. Lower handier 3. Handle bolt 2. Upper handier 4. Eye bolt 1. Key switch 5. Alec. start button® 2. Primer 6. Cord connection™ 3. Re coll start * ELEV. START MODEL 4. Choke 625 1. Deadbolt 3. Rear hole 2.
1. Wear indicator hot 1. Rotor blade (2) 2. Rotor naif (2) 3. Cork screw {3) 4. Lockout {13} 5. Hex-head cap screw (4) 6. Spacer {4) 7. Auger shaft assembly 8.
Contents Introduction Safety .. Before Operating ‘While Operating . . . Maintaining Snow thrower . Safety and Instruction Decals Assembly .. .. Install Wheels . . . Install Hate Crank . .. Install Discharge Chute Install Handle . . .. Install Control Cable Before Starting . .. Mix Gasoline And Ol Operation . i, Starting/Stopping Engine Operating TIPS <. ..o vnninrinenon,s Maintenance ..
WARNING signals a hazard that may cause serious 3. injury or death if the recommended precautions are not followed, CAUTION signals a hazard that may cause minor or moderate injury if the recommended precautions are not followed. Two other words are also used to highlight information. “Important” calls attention to special mechanical information and “Note” emphasizes general information worthy of special attention. The left and right side of the machine is determined 6.
water or when hands are wet. Do not use cord if gasoline has been spilled. If extension cord is damaged, replace immediately (Part No. 28-9170). Never direct discharge toward or operate snow thrower near bystanders, glass enclosures, automobiles and trucks, window wells or a drop-off. Never allow anyone in front of snow thrower. Keep people and pets a safe distance away from the snow thrower and area of operation. Operate the snow thrower only when there is good visibility or light.
Safety and instruction Decals Safety decals and instinct ions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 'DANGER ON INSIDE OF BELT COVER {Part No. 60-9480) ENGAGE DISENGAGE o ROTOR DRIVE |§ SE-sero HANDLE ON CHUTE {Part No. 66~6870) {Part No. 94-2900) Using a hammer, strike the push nut to seat the y nut FIRMLY in place.
chute ring turns with crank. Make sure plastic bushing is fully inserted into hole in mounting bracket, then secure mounting bracket to handle with (2) cap screws and lockouts. Install Discharge Chute (Fig. 4) 1. Set discharge chute onto chute ring. Align hole in back of chute with center hole in ring and install a carriage bolt and mess lockout. Position nut on outside of chute. Note: Chute ring may be rotated to case assembly of discharge chute. 2.
with two gallons of fresh, unleaded regular gasoline, You can also use Toto “Easy Mix” Two—Cycle Oil (3.2 ounce bottle mixed one per gallon of gasoline; 40:1 ratio) in this Tore two-cycle engine. Leaded regular gasoline may be used if unleaded regular is not available. Toto Two~Cycle Oil is specially formulated to provide superior lubrication, make starting easy, and prolong engine life. If Toto Two-Cycle Oil is not available, mix two gallons of gasoline and 5.
4, 6. ELECTRIC STARTING—Connect extension cord to snow thrower and standard household power outlet. Push starter button. IMPORTANT: Excessive running of the electric starter could damage the starter due to overheating. To prevent possible damage, do not run electric starter more than 10 times at intervals of 5 seconds ON, 5 seconds OFF, Then wait more than 40 inmates to allow starter to cool before continuing to run starter.
IMPORTANT: STORE SNOW THROWER IN OPERATING POSITION OBITS WHEELS, TIPPING OR STORING UNIT FORWARD ONTO FRONT HOUSING MAY CAUSE HARD STARTING. Maintenance General Maintenance Normally, the only maintenance required is cleaning the unit and tightening nuts, bolts, and screws. However, the scraper, drive belt, rotor blades, and spark plug should be checked once a year. Adjusting Control Bar Periodically check control bar for proper adjustment. Lo Turk ignition key 10 OFF. 2. CHECK ADJUSTMENT (Fig.
5. Install new scraper to housing using carriage bolts and nuts. Replacing Drive Belt (Fig. 13-14) Inspect drive belt before each season. If ribs on inside of belt are damaged or belt is worn, replacement is necessary. 1. Turn ignition key to OFF. 2. Remove (3) self tapping screws, (2) cap screws, (1) washer and (2) nuts securing belt cover to snow thrower frame (Fig. 13). Set belt cover aside. 3. REMOVING BELT {Fig.
Loosen the hex-head screw securing the rotor halves to the auger shaft assembly (Fig. 19). Slide the blade out from between the rotor halves (Fig. 19). Installing New Blade L 10 The rotor blades are made of laminated rubber. Examine the edge of a blade to see the difference in layer thicknesses (Fig. 20). (Some blades have a part number on the thick side of the blade.) Both blades must be installed with the thick layer on the inside of the curve.
It is Toto's policy to design and produce high In addition to The Toto Total Coverage Quality products. To ensure customer satisfactions, we are so confident that the TOR GTS son, Toto has extensive warranty coverage on Engine will provide a high level of perform its products. Your TOR GTS Engine powered acne and durability that we are providing & product has two warranty statements covering Starting Guarantee! Please read the details of it.
What Does This Warranty Not Cover? This Warranty does not cover: 1. Any repairs on products used commercially. 2. Normal maintenance including replacement of spark plugs, air filter, fuel fitter, and carburetor adjustments. 3. Ol change and lubrication. 4. Repairs or adjustments due to: 8. Failure to follow proper maintenance procedures; b. Rotary mower blade or snow thrower auger/paddies striking an object; c. Contaminants in the fuse system; d.
GUARANTEED TO START MAINTENANCE RECORD To keep the starting guarantee in effect, you must perform the following maintenance after every 25 operating hours, more often in dusty and dirty conditions.
Gas Powered G Consumer Products Except WPM THE TOR TOTAL COVERAGE GUARANTEE A Full Two~Year Warranty (Limited Warranty for Commercial Use) What |s Covered By This Express Warranty? The Toto Company promises to repair any TOR Product used for normal residential purposes™ if defective in materials or workmanship for & period of two years from the date of purchase. The cost of parts and labor is included, but the customer pays the transportation costs.