Operator's Manual

ManualsBrandsToro ManualsOutdoorsPower Clear 518 ZR 18 in. Single-Stage Gas Snow Blower

FormNo.3415-616RevB

PowerClear®518Snowthrower

ModelNo.38472—SerialNo.402082000andUp

ModelNo.38473—SerialNo.402082000andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedprimarilyforremoving

snowfrompavedsurfaces,suchasdrivewaysand

sidewalks,andothersurfacesfortrafconresidential

orcommercialproperties.Itisnotdesignedfor

removingmaterialsotherthansnow,norisitdesigned

forclearinggravelsurfaces.

Note:Themachinemayleaverubbermarkson

newbrushedorlight-coloredconcrete.Testonan

inconspicuouslocationbeforeuse.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

YoumaycontactT orodirectlyatwww.Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyoursmartphoneortablet,scan

theQRcodeontheserialnumberdecaltoaccess

warranty,parts,andotherproductinformation.

g216757

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedinMexico

AllRightsReserved

*3415-616*B

Summary of content (16 pages)

PAGE 1
Form No. 3415-616 Rev B Power Clear® 518 Snowthrower Model No. 38472—Serial No. 402082000 and Up Model No. 38473—Serial No. 402082000 and Up Operator's Manual Introduction Model No. This machine is intended to be used by residential homeowners. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties.
PAGE 2
Contents WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Introduction ............................................................... 1 Safety ....................................................................... 3 General Safety ..
PAGE 3
Safety • Do not operate the machine without all guards General Safety • Keep clear of any discharge opening. Keep and other safety protective devices in place and working on the machine. bystanders a safe distance away from the machine. This machine complies with ANSI B71.3 specifications. • Read and understand the contents of this • Keep children out of the operating area. Never Operator’s Manual before you start the engine.
PAGE 4
Installing the Recoil-Start Handle Setup Installing the Handle g218390 Filling the Engine with Oil g218388 Installing the Discharge Chute g218389 g216207 Adjusting the Control Cable Refer to Checking and Adjusting the Control Cable (page 12).
PAGE 5
Product Overview Operation Note: Determine the left and right sides of the machine from the normal operating position. Before Operation Before Operation Safety • For electric-start models only: Use extension cords and receptacles as specified in the manual. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it. Replace the damaged cord. Unplug the power cord whenever you are not starting the machine.
PAGE 6
Filling the Fuel Tank Checking the Engine-Oil Level • For best results, use only clean, fresh (less than 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). Service Interval: Before each use or daily • Oxygenated fuel with up to 10% ethanol or 15% MTBE by volume is acceptable. • Do not use ethanol blends of gasoline (such as E15 or E85) with more than 10% ethanol by volume.
PAGE 7
Starting the Engine During Operation 1. During Operation Safety Push the ignition key fully inward to the ON position (Figure 12). • Shut off the engine before unclogging the machine and always use a stick or the snow-cleanout tool (if provided). • A rotating auger can injure hands or feet. Stay behind the handles and away from the discharge opening while operating the machine. Keep your face, hands, feet, and any other part of your body or clothing away from moving or rotating parts.
PAGE 8
WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance. g013826 Figure 14 Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole. Important: Do not use the primer or the choke if the engine has been running and is hot.
PAGE 9
Engaging the Rotor Blades Shutting Off the Engine To engage the rotor blades, hold the control bar against the handle (Figure 17). To shut off the engine, pull the ignition key outward until it clicks into the OFF position (Figure 19) or move the choke lever fully to the right (Figure 13). g011577 Figure 17 g013828 Figure 19 1. Ignition key Disengaging the Rotor Blades To disengage the rotor blades, release the control bar (Figure 18).
PAGE 10
Adjusting the Discharge Chute and Chute Deflector Self-Propelling the Snowthrower To adjust the discharge chute, move the chute handle as shown in Figure 20. Lift the machine handle until the wheels are just off the ground and the scraper and rotor blades touch the ground. The machine propels forward (Figure 22). g011580 Figure 20 1.
PAGE 11
After Operation After Operation Safety • Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure. • When storing the machine for more than 30 days, refer to Storing the Machine (page 16) for important details. Preventing Freeze-up after Use • Let the engine run for a few minutes to prevent moving parts from freezing.
PAGE 12
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour After the first 2 hours Before each use or daily Yearly Yearly or before storage Maintenance Procedure • Check the control cable and adjust it if necessary. • Check for loose fasteners and tighten them if necessary. • Change the engine oil. • Check the engine-oil level and add oil if necessary. • Check the control cable and adjust it if necessary.
PAGE 13
Adjusting the Control Cable 1. Slide up the spring cover and unhook the spring from the adjuster link (Figure 24). g011544 Figure 25 1. The wear-indicator hole is intact; you do not need to replace the rotor blades. Changing the Engine Oil g006402 Figure 24 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. Service Interval: After the first 2 hours Yearly If possible, run the engine for a few minutes before changing the oil to warm it.
PAGE 14
9. Screw the oil-fill cap into the oil-fill hole, and tighten it securely by hand. 10. Wipe up any spilled oil. 11. Dispose of the used oil properly at a local recycling center. Servicing the Spark Plug Service Interval: Yearly—Service the spark plug and replace it if necessary. Use a Toro spark plug (Part No. 119-1961). g013824 Figure 26 1. The oil level is at its maximum. 3. The oil level is too low—add oil to the crankcase. 1. Shut off the engine and wait for all moving parts to stop. 2.
PAGE 15
Replacing the Drive Belt If drive belt becomes worn, oil-soaked, excessively cracked, frayed, or otherwise damaged, replace the belt. 1. Remove the 4 bolts that hold the drive-belt cover (Figure 29) in place. g011642 Figure 30 1. Belt guide 2. Engine pulley Note: Do not distort or damage the belt guide. 6. To install the new drive belt, reverse the steps above.
PAGE 16
Storage Storing the Machine WARNING Fuel fumes are highly flammable, explosive, and dangerous if inhaled. If you store the product in an area with an open flame, the fuel fumes may ignite and cause an explosion. • Do not store the machine in a house (living area), basement, or any other area where ignition sources may be present, such as hot water and space heaters, clothes dryers, furnaces, and other appliances. g013829 Figure 32 1.