Form No. 3360-104 Rev D Power Max® 826 OE Snowthrower Model No. 38629C—Serial No. 280000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.
Safety Caution: Improper use may result in loss of fingers, hands, or feet. Before Operating ? ? Read and understand the contents of this manual before operating the snowthrower Become familiar with all controls and know how to stop the engine quickly . . There is a high-speed impeller close to the opening. Operator 's Position The low-speed auger has a moving pinch point close to the opening. This snowthrower meets or exceeds the B71.
• • • • – When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle. – Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refueling is complete. Do not use a nozzle lock-open device. – Replace gasoline cap securely and wipe up spilled fuel.
• Always refer to the Operator’s Manual for important details if the snow thrower is to be stored for an extended period. • Perform only those maintenance instructions described in this manual. Before performing any maintenance, service, or adjustment, stop the engine, remove the key, and disconnect the wire from the spark plug. If major repairs are ever needed, contact your Authorized Service Dealer. • Maintain or replace safety and instruction labels, as necessary.
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 107-3040 1. Cutting dismemberment, impeller and cutting dismemberment, auger hazards—keep bystanders a safe distance from the snowthrower. 106-4525 Reorder part no. 112-6631 1. Fast 2. Forward speeds 3. Slow 4. Reverse speeds 112-6625 Reorder part no. 112-6629 1.
Briggs Part No. 273676 3. Fast 1. Stop 2. Slow Briggs Part No. 274681 1. Fuel—On 2. Fuel—Off Briggs Part No. 276923 1. Primer 2. Choke off (Run) 4. Ignition key in (Engine—Run) 5. Ignition key out (Engine—Stop) 3. Choke on (Choke) Briggs Part No. 276925 1. Warning—read the Operator’s Manual. 2. Warning—fire hazard. 3. Warning—toxic gas inhalation hazard. 4. Warning—hot surface/burn hazard. Briggs Part No. 277566 1. When starting a cold engine, close the choke and press the primer two times. 2.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1. 2. 3. 4. 5. 6. 7. Description Use Qty. Handle bolts Curved washers Locknuts 4 4 4 Install the upper handle. No parts required – Install the traction control linkage. Carriage bolts Locknuts 2 2 Install the chute control rod. No parts required – Fill the engine with oil. No parts required – Check the tire pressure. No parts required – Check the skids and scraper.
Figure 6 1. Speed selector lever 2. Trunnion 3. Inner washer 4. Outer washer Figure 4 Note: To make installation easier, leave the flat washer on the trunnion (Figure 6). 2. Installing the Traction Control Linkage 4. Shift the speed selector lever into Position R2. 5. Rotate the lower link arm fully upward (counterclockwise) (Figure 7). Procedure 1.
Note: For easier installation, look down through the opening in the speed selector (Figure 8). 4. Insert the front end of the rod into the opening in the back of the chute gear cover until it slides into the chute gear (Figure 10). Figure 8 1. Speed selector 3. Installing the Chute Control Rod 2 Carriage bolts 2 Locknuts Figure 10 5.
4. Filling the Engine with Oil 6. Checking the Skids and Scraper Procedure Procedure Your snowthrower comes with 20 oz. (0.59 l) of oil in the engine crankcase. Refer to Checking and Adjusting the Skids and Scraper in Maintenance. Note: Before starting the engine, check the oil level and add oil if necessary. 7. Checking the Traction Drive Operation Max. fill: 20 oz. (0.59 l), type: automotive detergent oil with an API service classification of SF, SG, SH, SJ, SL, or higher.
Product Overview 5. Move the speed selector to the Position 1; refer to Operating the Speed Selector. 6. Squeeze the left hand (traction) lever to the hand-grip (Figure 13). The snowthrower should move forward. If the snowthrower does not move or moves rearward, complete the following: A. Release the traction lever and stop the engine. B. Disconnect the trunnion from the speed selector lever (Figure 6). C. Turn the trunnion upward (counterclockwise) on the speed control rod (Figure 6). D.
Figure 16 1. Snow cleanout tool (attached to the handle) Operation Note: Determine the left and right sides of the machine from the normal operating position. Filling the Fuel Tank Figure 17 1. 1-1/2 inch (3.8 cm) Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can burn you and others. Starting the Engine • To prevent a static charge from igniting the gasoline, place the container and/or snowthrower on the ground before filling, not in a vehicle or on an object. 1.
Figure 21 6. Move the throttle to the Fast position (Figure 22). Figure 19 1. Ignition key 4. Firmly push in the primer with your thumb 2 times (15°F or -9°C or above) or 4 times (below 15°F or -9°C), holding the primer in for a second before releasing it each time (Figure 20). Figure 22 7. Start the snowthrower pulling the recoil starter or pressing the electric-starter button (Figure 23). Figure 20 Figure 23 5. Rotate the choke to the Choke position (Figure 21). 1. Electric-starter button 2.
maximum, then wait one minute before trying to start it again). If the engine still does not start, take the snowthrower to an Authorized Service Dealer for service. 8. Disconnect the power cord from the power outlet first and then from the snowthrower (electric start only). 9. Allow the engine to warm up for several minutes, move the choke toward the Run position. Wait for the engine to run smoothly before each choke adjustment. Figure 25 5. Pull the recoil starter 3 or 4 times.
traction lever locks the auger/impeller lever down, freeing your right hand. To release both levers, simply release the left hand (traction) lever. 3. If the auger and impeller continue to rotate when you release the auger/impeller lever, do not operate the snowthrower. Check the auger/impeller cable (refer to Checking and Adjusting the Auger/Impeller Cable) and adjust it if necessary. Otherwise, take the snowthrower to an Authorized Dealer for service. Figure 26 2.
Unclogging the Discharge Chute If the auger/impeller is running but there is no snow coming out of the discharge chute, the discharge chute may be clogged. • To unclog the discharge chute, stay in the operating position and release the left hand (traction) lever. While running the auger/impeller, push down on the handles to raise the front of the snowthrower a few inches (centimeters) off the pavement. Then lift the handles quickly to bump the front of the snowthrower on the pavement.
Operating Tips When the snowthrower is in operation, the auger and impeller can rotate and cut off or injure hands and feet. • Before adjusting, cleaning, inspecting, troubleshooting, or repairing the snowthrower, stop the engine and wait for all moving parts to stop. Disconnect the wire from the spark plug and keep it away from the plug to prevent someone from accidentally starting the engine. • Remove an obstruction from the discharge chute; refer to Unclogging the Discharge Chute.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 2 hours • Inspect the traction cable and adjust it if necessary. • Inspect the auger/impeller cable and adjust it if necessary. After the first 5 hours • Change the engine oil. Before each use or daily • Check the engine oil level and add oil if necessary.
Checking and Adjusting the Skids and Scraper Checking and Adjusting the Traction Cable Service Interval: Yearly—Check the skids and the scraper and adjust them if necessary. Service Interval: After the first 2 hours—Inspect the traction cable and adjust it if necessary. Check the skids and the scraper to ensure that the auger does not contact the paved or gravel surface. Adjust the skids and the scraper as needed to compensate for wear.
Figure 35 1. Jam nut Figure 37 2. Turnbuckle 1. Tab 2. 1/16 inch (1.5 mm) Checking and Adjusting the Auger/Impeller Cable 4. If the auger/impeller cable is not properly adjusted, do the following steps: 5. Loosen the jam nut (Figure 38). Service Interval: After the first 2 hours—Inspect the auger/impeller cable and adjust it if necessary. Yearly—Inspect the auger/impeller cable and adjust or replace it if necessary. 1. Remove the 2 screws from the right side of the belt cover as shown. 2.
Checking the Auger Gearbox Oil Level Service Interval: Yearly—Check the auger gearbox oil and add oil if necessary. Figure 40 1. Move the snowthrower to a level surface. 1. Oil drain cap 2. Clean the area around the pipe plug (Figure 39). 2. Slide an oil drain pan under the drain extension and remove the oil drain cap. 3. Drain the oil. Note: Dispose of the used oil properly at a local recycling center. 4. Install the oil drain cap. 5. Fill the crankcase with oil.
4. Remove the bracket thumb screw and the bracket (Figure 44). Figure 42 1. Back cover 4. Move the speed selector lever to Position R2. 5. Dip your finger in automotive engine oil and lightly lubricate hex shaft. 6. Move the speed selector lever to Position 6. 7. Lubricate the other end of the hex shaft. 8. Move the speed selector lever forward and rearward a few times. 9. Install the back cover and return the snowthrower to the operating position. Figure 44 Replacing the Spark Plug 3. Thumb screw 1.
12. Align the tab on the choke control knob with the slot on the upper snow hood. 13. Connect the choke control knob to the choke shaft on the carburetor. Adjusting the Discharge Chute Latch If the discharge chute does not lock into the desired position or does not unlock so that you can move it to another position, adjust the discharge chute latch. Figure 48 1. Discharge chute latch 1.
Storage 16. Touch up chipped surfaces with paint available from an Authorized Service Dealer. Sand affected areas before painting, and use a rust preventative to prevent the metal parts from rusting. 17. Tighten all loose screws, bolts, and locknuts. Repair or replace any damaged parts. • Gasoline vapors can explode. • Do not store gasoline more than 30 days. 18. Cover the snowthrower and store it in a clean, dry place out of the reach of children.
Troubleshooting Problem Possible Cause Electric starter does not turn (electric-start models only) 1. The power cord is disconnected at the outlet or the snowthrower. 1. Connect the power cord to the outlet and/or the snowthrower. 2. The power cord is worn, corroded, or damaged. 3. The power outlet is not energized. 2. Replace the power cord. 1. The key is not in the ignition or is in the Stop position. 1. Insert the key into the ignition and turn it to the On position. 2.
Problem Possible Cause Corrective Action 7. The auger/impeller drive belt is worn or broken. 7. Replace the auger/impeller drive belt; refer to www.Toro.com for servicing information or take the snowthrower to an Authorized Service Dealer. Discharge chute either does not lock into place or does not move 1. The discharge chute latch is not properly adjusted. 1. Adjust the discharge chute latch. Snowthrower does not properly clear the snow off the surface 1.
Notes: 27
Gas Powered Snow Products The Toro Total Coverage Guarantee A Two-Year Full Warranty (Limited Warranty for Commercial Use) Conditions and Products Covered Owner Responsibilities The Toro Company and its afliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship.