Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38710

FormNo.3396-378RevA

SnowMax724ZXRSnowthrower

ModelNo.38710—SerialNo.316000001andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedforremovingsnowfrom

pavedsurfaces,suchasdrivewaysandsidewalks,and

othersurfacesfortrafconresidentialorcommercial

properties.Itisnotdesignedforremovingmaterials

otherthansnow,norisitdesignedforclearingoffgravel

surfaces.

Readthisinformationcarefullytolearnhowtooperateand

maintainyourmachineproperlyandtoavoidinjuryand

machinedamage.Youareresponsibleforoperatingthe

machineproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.comformachine

andaccessoryinformation,helpndingadealer,ortoregister

yourmachine.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourmachineready.Figure1identiesthelocationofthe

modelandserialnumbersonthemachine.Writethenumbers

inthespaceprovided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

Formodelswithstatedpower,thenetpoweroftheenginewas

laboratoryratedbytheenginemanufacturerinaccordance

withSAEJ1940.Asconguredtomeetsafety,emission,and

operatingrequirements,theactualenginehorsepoweronthis

classofsnowthrowerwillbesignicantlylower.

Contents

Introduction..................................................................1

Safety...........................................................................2

SoundPressure.......................................................2

SoundPower..........................................................2

Vibration................................................................2

SafetyandInstructionalDecals.................................3

Setup............................................................................4

1UnfoldingtheHandle............................................4

2InstallingtheDischargeChute................................5

3FillingtheEnginewithOil......................................5

ProductOverview..........................................................6

Operation.....................................................................7

BeforeOperation.......................................................7

Safety.....................................................................7

FillingtheFuelTank................................................7

CheckingtheEngine-OilLevel..................................7

DuringOperation......................................................7

Safety.....................................................................7

StartingtheEngine..................................................8

EngagingtheAuger.................................................9

DisengagingtheAuger.............................................9

Self-PropellingtheMachine......................................9

StoppingtheEngine................................................9

AdjustingtheDischargeChuteandChute

Deector............................................................9

ClearingaCloggedDischargeChute..........................9

OperatingTips......................................................10

AfterOperation........................................................10

Safety....................................................................10

PreventingFreeze-upafterUse.................................10

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3396-378*A

Summary of content (20 pages)

PAGE 1
Form No. 3396-378 Rev A SnowMax 724 ZXR Snowthrower Model No. 38710—Serial No. 316000001 and Up Operator's Manual Introduction This machine is intended to be used by residential homeowners. It is designed for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties. It is not designed for removing materials other than snow, nor is it designed for clearing off gravel surfaces.
PAGE 2
Safety Maintenance .................................................................11 Recommended Maintenance Schedule(s) ......................11 Maintenance Safety.................................................11 Checking the Engine Oil Level .................................11 Checking and Adjusting the Skids .............................12 Inspecting the Throwing Edges ................................12 Changing the Engine Oil .........................................12 Replacing the Spark Plug ....
PAGE 3
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 1 2 x3 3 4 5 120-9805 120-9805 131–5914 Order part no. 131–5916 1. Insert the key. 2. Prime the engine 3 times. 3. Engage the choke. 1. Cutting/dismemberment hazard of hand or foot, auger—do not place your hand in the chute; remove the ignition key and read the instructions before servicing or performing maintenance. 4. Pull the starter cord. 5.
PAGE 4
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Qty. Use No parts required – Unfold the handle. Bolt (1/4–20 X 1–1/2 inch) Locknut (1/4–20 inch) 1 1 Install the discharge chute. 1 Unfolding the Handle No Parts Required Procedure Important: Ensure that the cables are not pinched when unfolding the handle.
PAGE 5
2 Model Max fill 38710 0.5 L (16.9 oz) Installing the Discharge Chute Oil type: automotive detergent oil with an API service classification of SJ, SL, or higher. Parts needed for this procedure: Use Figure 5 below to select the best oil viscosity for the outdoor temperature range expected: 1 Bolt (1/4–20 X 1–1/2 inch) 1 Locknut (1/4–20 inch) Procedure Insert the chute post through the bracket into the base of the machine and secure it using a bolt and a lock nut (Figure 4). Figure 5 1.
PAGE 6
Product Overview Figure 7 1. Auger lever 7. Discharge chute 2. Fuel tank cap 8. Chute deflector 3. Dipstick 9. Chute deflector control 4. Skid 10. Discharge chute control 5. Auger 11. Upper handle 6. Scraper Figure 8 Figure 6 1. Low oil level—add oil 2. Correct oil level 6 1. Fuel tank cap 4. Choke 2. Primer 3. Ignition key 5.
PAGE 7
Operation Before Operation • • Safety • Use extension cords and receptacles as specified by • • • • the manufacturer for all machines with electric starting motors. Do not operate the machine without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear slip resistant footwear that will improve footing on slippery surfaces.
PAGE 8
• Exercise extreme caution when operating on slopes. Starting the Engine • Never operate the machine without good visibility or Note: Fully insert the key to start the engine. The middle position will not start the engine. light. • Look behind and use care when backing up with the machine. • When not actively clearing snow, disengage power to the rotor blades. • Use extension cords and receptacles as specified by the manufacturer for all machines with electric starting motors.
PAGE 9
Engaging the Auger Adjusting the Discharge Chute and Chute Deflector To raise or lower the angle of the chute deflector, press the trigger on the chute deflector and move the chute deflector up or down. To adjust the discharge chute, move the chute handle Note: Disengage the auger before adjusting the chute or chute deflector. Figure 11 Disengaging the Auger To disengage the auger, release the auger lever.
PAGE 10
• Do not use the chute control to attempt to move a frozen cause the skids to move. Adjust the skids and tighten the skid bolts securely; refer to Checking and Adjusting the Skids (page 12). discharge chute. Hold down the blue knob and use your hands to rotate the chute. • Transporting the machine in an open trailer or vehicle can Operating Tips cause the controls or discharge chute to freeze.
PAGE 11
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first hour • Check for loose fasteners and tighten them if necessary. After the first 2 hours • Change the engine oil. • Inspect the auger cable and adjust it if necessary. • Inspect the transmission cable and adjust it if necessary.
PAGE 12
Checking and Adjusting the Skids Inspecting the Throwing Edges Service Interval: Yearly Service Interval: Yearly—Inspect the throwing edges and have an Authorized Service Dealer replace the throwing edges and scraper if necessary. Check the skids to ensure that the auger does not contact the paved surface. Adjust the skids as needed to compensate for wear (Figure 15). Before each session, inspect the throwing edges for wear.
PAGE 13
Figure 17 1. Oil-drain plug 3. After draining the used oil, return the machine to the operating position. 4. Install the oil drain plug and tighten it securely. 5. Clean around the oil fill cap. 6. Use Figure 18 below to select the best oil viscosity for the outdoor temperature range expected: Model Max fill 38710 0.5 L (16.9 oz) Oil type: automotive detergent oil with an API service classification of SJ, SL, or higher. Figure 18 Figure 19 1. Low oil level—add oil 13 2.
PAGE 14
Replacing the Spark Plug 1. Loosen the nut on the lower cable clamp, but do not remove it (Figure 22). Service Interval: Every 100 hours—Replace the spark plug. WARNING Replacing the spark plug while the engine is hot can result in burns. Wait until the engine is cool to replace the spark plug. Use a Toro spark plug or equivalent (Champion® RN9YC or NGK BPR6ES). 1. Remove the boot (Figure 20). Figure 22 1. Nut 2. Cable 3. Connector 4. Spring 2. Pull the cable up to remove some slack (Figure 22).
PAGE 15
Storage Storing the Snowthrower WARNING • Gasoline fumes are highly flammable, explosive, and dangerous if inhaled. If you store the machine in an area with an open flame, the gasoline fumes may ignite and cause an explosion. • Do not store the machine in a house (living area), basement, or any other area where ignition sources may be present, such as hot water and space heaters, clothes dryers, furnaces, and other like appliances.
PAGE 16
. Cover the machine and store it in a clean, dry place out of the reach of children. Allow the engine to cool before storing it in any enclosure.
PAGE 17
Notes: 17
PAGE 18
Notes: 18
PAGE 19
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
PAGE 20
Residential Snow Products The Toro Warranty and The Toro GTS Starting Guarantee Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair for the original purchaser1 the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual have been perform